Q6600 Overclock and Temperature
|
|
 Jul 24 2007, 09:57 PM, updated 17y ago
Show posts by this member only | Post
#1
|
 
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land   
|
I am getting a Q6600 next week, but depend on the temperature and overclockability of current B3 stepping, I may wait until end of August to go for G0 stepping.
So, I need to know, what is the temperature and voltage required to push the current B3 Q6600 to 3.4GHz? sincerly need help, please post your comment. |
|
|
|
|
|
Jul 24 2007, 09:59 PM
Show posts by this member only | Post
#2
|
Senior Member
3,658 posts Joined: Jan 2003 
|
me 2.......wah u open so many q6600 question thread must eveyday dream bout q6600
same here |
|
|
Jul 24 2007, 10:06 PM
Show posts by this member only | Post
#3
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
haha, not because dream about it, because some friend want to buy my current E6600 next week, so i have to decide should i let go my E6600 and go for B3 Q6600, or should I wait for G0 Q6600.....
Added on July 24, 2007, 10:07 pmk8118k, since you are using Q6600, why dont you tell me your result?  This post has been edited by TaiZi@CCF: Jul 24 2007, 10:07 PM |
|
|
Jul 24 2007, 10:19 PM
Show posts by this member only | Post
#4
|
Senior Member
676 posts Joined: Jul 2007 From: Soviet Union
|
errr what is G0 ????= = n B3???
Added on July 24, 2007, 10:37 pmnwm i know wat is b3 n G0.....rdy....BS use 105 w G0 use 90 w....n bah bah!!!good for hardcore OC ~.~......is release mabye AUG mid.... This post has been edited by commanderz: Jul 24 2007, 10:37 PM |
|
|
Jul 24 2007, 11:02 PM
Show posts by this member only | Post
#5
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL 
|
Wait until some reviewer like irenic that might got G0 stepping on his hands later.
|
|
|
Jul 25 2007, 01:18 AM
Show posts by this member only | Post
#6
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(§layerXT @ Jul 24 2007, 11:02 PM) Wait until some reviewer like irenic that might got G0 stepping on his hands later. haha yeah myb need wait sum forumer to tested it like irenic our QS   |
|
|
|
|
|
Jul 25 2007, 02:18 AM
Show posts by this member only | Post
#7
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
wah u guys wish i become lab mouse ar ?
heheerm actually, i already grabbed myself a q6600 B3 stepping .. i know i should wait with G0 but since i have no processor to use, i've no choice but to buy this.. maybe if it's so sux, i'll buy a G0 once it becomes available in the store.. and the real reason i bought this quad core over the E6850 is bcoz i got few video editting works to be finished by next month.. so hopefully it worth to use this q6600 over the super overclocked E6850..  i'll share some info soon  Default Q6600 Idle temp..  Default Q6600 Load temp (15mins stress test)  This post has been edited by irenic: Jul 25 2007, 02:58 AM |
|
|
Jul 25 2007, 03:06 AM
Show posts by this member only | Post
#8
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(irenic @ Jul 25 2007, 02:18 AM) wah u guys wish i become lab mouse ar ? haha richest lab mouse..haha famous than STUART heheerm actually, i already grabbed myself a q6600 B3 stepping .. i know i should wait with G0 but since i have no processor to use, i've no choice but to buy this.. maybe if it's so sux, i'll buy a G0 once it becomes available in the store.. and the real reason i bought this quad core over the E6850 is bcoz i got few video editting works to be finished by next month.. so hopefully it worth to use this q6600 over the super overclocked E6850.. i'll share some info soon later still getting q66?y not take x6850  |
|
|
Jul 25 2007, 03:09 AM
Show posts by this member only | Post
#9
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
QUOTE(mfcm @ Jul 25 2007, 03:06 AM) haha richest lab mouse..haha famous than STUART enuff bout mouse..i hate mouse.. haha but stuart little is ok later still getting q66?y not take x6850 erm yeah QX6850 is tempting.. but i wont spend so much bcoz better processor in penryn will be released later on.. |
|
|
Jul 25 2007, 05:22 AM
|
Senior Member
835 posts Joined: Sep 2004 From: LYP@Bintang Walk
|
My Q6600 B3 temp
Attached thumbnail(s) 
|
|
|
Jul 25 2007, 11:15 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
so far i can boot at 4ghz, but then BSOD when i was login the password at vista..
and max bootable into windows is 3.85ghz.. aquamark and cinebench stable.. PI havent chance to do it coz it's located in an external drive n my friend borrow the external case.. 3.85ghz:  3.85ghz cinebench: 
3.85ghz aquamark (2900XT @ default): 
3.80Ghz 3dmark06, xt @ 850/1100:  |
|
|
Jul 25 2007, 12:08 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
irenic, what is your vcore and temperature?
|
|
|
Jul 25 2007, 12:14 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
now the next quest is to find sweet spot for daily use.. i dun want to use more than 1.4v for 24/7 so let see whether this q6600 is like most c2d where 3.2ghz @ default vcore is just piece of cake..
 Added on July 25, 2007, 12:16 pm QUOTE(TaiZi@CCF @ Jul 25 2007, 12:08 PM) irenic, what is your vcore and temperature? my vcore @ 3.8ghz is 1.55v while 3.85 is 1.6v.. temp idle is around 52c max, load is around 65c maxThis post has been edited by irenic: Jul 25 2007, 12:16 PM |
|
|
|
|
|
Jul 25 2007, 12:18 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
QUOTE(irenic @ Jul 25 2007, 12:14 PM) now the next quest is to find sweet spot for daily use.. i dun want to use more than 1.4v for 24/7 so let see whether this q6600 is like most c2d where 3.2ghz @ default vcore is just piece of cake.. So, this is a pretty good result, what cooling you using?Added on July 25, 2007, 12:16 pm my vcore @ 3.8ghz is 1.55v while 3.85 is 1.6v.. temp idle is around 52c max, load is around 65c max I am going to get a B3 stepping next week, no need to wait for G0 since i am on water cooling, should be good enough to keep it cool. |
|
|
Jul 25 2007, 12:44 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
QUOTE(TaiZi@CCF @ Jul 25 2007, 12:18 PM) So, this is a pretty good result, what cooling you using? watercooling.. erm well if u browse around here :I am going to get a B3 stepping next week, no need to wait for G0 since i am on water cooling, should be good enough to keep it cool. http://www.xtremesystems.org/forums/showth...t=152603&page=5 u'll found out that so far the retail G0 oc potential is same like B3, just that it runs cooler.. but not much i can say..  This post has been edited by irenic: Jul 25 2007, 01:05 PM |
|
|
Jul 25 2007, 07:30 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
 oc potential may not differ that much, but maybe G0 runs cooler mean better life span when oc such as high as 3.8GHz. |
|
|
Jul 26 2007, 12:20 AM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
I need all the guru to help me.....
I dont know why, I got my Q6600 today, tested all stable, duo orthos full 4 core prime stable for more than 1 hours, I overclocked to only 3.2GHz with 1.375v. but why the hell my Q6600 running so hot??? I cant believe it how come irenic can get 65c full load at 1.55v.... please tell me why... getting mad.  
This post has been edited by TaiZi@CCF: Jul 26 2007, 12:27 AM |
|
|
Jul 26 2007, 12:37 AM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(TaiZi@CCF @ Jul 26 2007, 12:20 AM) I need all the guru to help me..... huhu izzit coz wat ppl said bout the quality of WC will give u better performance I dont know why, I got my Q6600 today, tested all stable, duo orthos full 4 core prime stable for more than 1 hours, I overclocked to only 3.2GHz with 1.375v. but why the hell my Q6600 running so hot??? I cant believe it how come irenic can get 65c full load at 1.55v.... please tell me why... getting mad.
  |
|
|
Jul 26 2007, 12:58 AM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
QUOTE(mfcm @ Jul 26 2007, 12:37 AM) huhu izzit coz wat ppl said bout the quality of WC will give u better performance will that be so much of different?... this same cooling kit was keeping my old setup E6600@3.4G 1.5v below 65C full load and 40C idle... but now it is 55C full load! i dont need water heater in my bed room anymore!  |
|
|
Jul 26 2007, 01:23 AM
|
Junior Member
302 posts Joined: Jun 2007 From: Johor 
|
i'll rather wait for the G0....cooler means higher overclockability (generally). Quad on cascade at -70c 4.5Ghz region would be rather nice i would say. Don't ya all agree. But then again i hope there isn't any hole in my pocket....
|
|
|
Jul 26 2007, 01:46 AM
|
Junior Member
151 posts Joined: Dec 2005
|
@taizi
wow...what a temp.what type wts u use? |
|
|
Jul 26 2007, 01:53 AM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
TT BigWater SE + CM AquaTrident CPU Block + additional radiator with fan(12CM TT Big Radiator with fan)
and something strange is, by touching the waterblock connector, i can feel that the water is not too hot because the copper connector is much cooler than my 8800GTS HSF(which reported only 63C), i believe the waterblock is perfectly seated and i dont know what make the heat not transfer to the waterblock, or perhaps it is just reporting error? siao liao la............... This post has been edited by TaiZi@CCF: Jul 26 2007, 01:54 AM |
|
|
Jul 26 2007, 03:54 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
wah ur temp damn hot.. 82c.. last time with my qx6700 and geminiII also wont reach above 70c :-s
erm maybe it's time for u to invest on better watercooling kit or high end aircooling.. and yes, G0 should run lots cooler than B3, but if u already own good wc kit, n manage to get good full load temp, so G0 or B3 wont make any difference.. |
|
|
Jul 26 2007, 08:16 AM
|
Senior Member
1,995 posts Joined: May 2005
|
q6600 seems to be quite capable too.........wander how it do on passive cooling hehe
make wanna change my e6600 to q6600 also lar |
|
|
Jul 26 2007, 08:41 AM
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(mfcm @ Jul 25 2007, 01:18 AM) haha yeah myb need wait sum forumer to tested it like irenic our QS w0ot bro, long time didnt c u online any latest updates ka?? |
|
|
Jul 26 2007, 09:11 AM
|
Senior Member
925 posts Joined: Jan 2005 From: depan lcd...dalam bilik..sekitar cyberjaya...
|
QUOTE(gengstapo @ Jul 26 2007, 08:41 AM) w0ot bro, long time didnt c u online he want Q66 lor...hehheheany latest updates ka?? info: B3 running used 105watt....G0 running used 95watt....10watt less... |
|
|
Jul 26 2007, 09:22 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(flatfinger @ Jul 26 2007, 09:11 AM) he want Q66 lor...hehhehe hehee.. q66 ehh? cant wait to see more result from this chipinfo: B3 running used 105watt....G0 running used 95watt....10watt less... when would the G0 will available in the store? |
|
|
Jul 26 2007, 10:10 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
some info regarding the G0 stepping...
http://www.xtremesystems.org/forums/showth...=152603&page=10 http://www.xtremesystems.org/forums/showthread.php?t=152722 ... looks so far only got 2-3 results.. 1 guy with aircooled manage to reach 3.6ghz stable on air, and max at 3.8ghz while the other guy stable at 3.4ghz @ 1.4vcore and 3.5ghz failed prime.. so far as predicted, G0 result is just on par as B3.. some are good n some are not.. |
|
|
Jul 26 2007, 10:42 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
It looks it still depends on ur luck too. But technically G0 have better characteristic when refer to Intel website. But maybe ppl wont see much differrent.
|
|
|
Jul 26 2007, 12:06 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(§layerXT @ Jul 26 2007, 10:42 AM) It looks it still depends on ur luck too. But technically G0 have better characteristic when refer to Intel website. But maybe ppl wont see much differrent. yess, only those extremist/ enthusiast pc hardware know & feel the different between both stepping   |
|
|
Jul 26 2007, 02:03 PM
|
Senior Member
8,753 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Jul 26 2007, 12:06 PM) yess, only those extremist/ enthusiast pc hardware know & feel the different between both stepping like what? less wattage.. less vcore? performance wise? or just 'feel' only.. |
|
|
Jul 26 2007, 02:26 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(8tvt @ Jul 26 2007, 02:03 PM) like what? less heat less wattage.. less vcore? performance wise? or just 'feel' only.. |
|
|
Jul 26 2007, 03:07 PM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(gengstapo @ Jul 26 2007, 08:41 AM) w0ot bro, long time didnt c u online haha..biasa ah..br abes cuti pjg..balik U br bole online any latest updates ka?? dok kg xde net update ek nk tgk dlu performace mana ok..then baru nk amik..myb duo..or quad QUOTE(flatfinger @ Jul 26 2007, 09:11 AM) he want Q66 lor...hehhehe haha pe pandai je ko nih..reki dlu mana ok info: B3 running used 105watt....G0 running used 95watt....10watt less... seem quad agak pns aku tgk..tgk plak G0 cmna plak temp dia..perhaps lower since low wattage  QUOTE(gengstapo @ Jul 26 2007, 02:26 PM) less heat then can oc higher if less heat This post has been edited by mfcm: Jul 26 2007, 03:14 PM |
|
|
Jul 26 2007, 03:51 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
irenic, what software you used to mionitor temperature? CoreTemp? or motherboard monitoring software? when coretemp showing 80C on full load, my gigabyte easy tune showing only 67C......
|
|
|
Jul 26 2007, 08:24 PM
|
 
Elite
6,139 posts Joined: Jan 2003
|
QUOTE(TaiZi@CCF @ Jul 26 2007, 12:20 AM) I need all the guru to help me..... i run linpack on stock Q6600 and stock heatsink and the temp hit 81C, what is yours compared to mine?I dont know why, I got my Q6600 today, tested all stable, duo orthos full 4 core prime stable for more than 1 hours, I overclocked to only 3.2GHz with 1.375v. but why the hell my Q6600 running so hot??? I cant believe it how come irenic can get 65c full load at 1.55v.... please tell me why... getting mad.
|
|
|
Jul 26 2007, 09:21 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
QUOTE(jinaun @ Jul 26 2007, 08:24 PM) i run linpack on stock Q6600 and stock heatsink and the temp hit 81C, what is yours compared to mine? jinaun, are you overclocked? what is the vcore?compared to yours, I am water cooled, and you are stock HSF, i think your is much much more cooler than mine... now i dont know should i trust coretemp or speedfan... speedfan, gigabyte easytune, bios all give same result, which is verymuch close to the water temperature, my water temperature is 44C. but, CoreTemp, Intel TAT, Everest give another result, which is almost 80C.......... which should I trust?  Attached thumbnail(s) 
|
|
|
Jul 26 2007, 09:33 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
QUOTE(TaiZi@CCF @ Jul 26 2007, 09:21 PM) jinaun, are you overclocked? what is the vcore? i think its due to reading from PECIcompared to yours, I am water cooled, and you are stock HSF, i think your is much much more cooler than mine... now i dont know should i trust coretemp or speedfan... speedfan, gigabyte easytune, bios all give same result, which is verymuch close to the water temperature, my water temperature is 44C. but, CoreTemp, Intel TAT, Everest give another result, which is almost 80C.......... which should I trust? |
|
|
Jul 26 2007, 09:38 PM
|
Senior Member
1,468 posts Joined: Sep 2006 From: Taman Melati, KL
|
QUOTE(TaiZi@CCF @ Jul 26 2007, 09:21 PM) jinaun, are you overclocked? what is the vcore? trust speed fan , coretemp always show wrong information ... compared to yours, I am water cooled, and you are stock HSF, i think your is much much more cooler than mine... now i dont know should i trust coretemp or speedfan... speedfan, gigabyte easytune, bios all give same result, which is verymuch close to the water temperature, my water temperature is 44C. but, CoreTemp, Intel TAT, Everest give another result, which is almost 80C.......... which should I trust? good luck in overclocking ... |
|
|
Jul 26 2007, 10:34 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
here is my temp..
the coretemp is more or less same as everest * notice that the GPU diode temp is higher than the GPU temp? Attached thumbnail(s) 
|
|
|
Jul 27 2007, 10:55 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
QUOTE(likito @ Jul 26 2007, 09:38 PM) trust speed fan , coretemp always show wrong information ... Speed fan shows surface core temp while coretemp shows tjunction temp which is different. good luck in overclocking ... This post has been edited by §layerXT: Jul 27 2007, 10:55 AM |
|
|
Jul 27 2007, 11:13 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
guys, why ur q6600 all are so hot?
|
|
|
Jul 27 2007, 11:28 AM
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(§layerXT @ Jul 27 2007, 10:55 AM) Speed fan shows surface core temp while coretemp shows tjunction temp which is different. Are you sure about this? I've been wondering about speedfan's reading too. There are usually a few readings showing in speedfan. CPU temp (only know if I correlate this temp reading with other software), Core0 temp and core1 temp. The CPU temp is usually about 6'c higher than the core0 and core1......... |
|
|
Jul 27 2007, 11:28 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Someone already compared Coretemp with TAT and the temp is very similar. TAT is build by Intel and this cant be wrong.
|
|
|
Jul 30 2007, 01:02 AM
|
|
Senior Member
3,658 posts Joined: Jan 2003
|
how to go to 36.
mine now 3.2 on 400 x8 |
|
|
Jul 30 2007, 02:13 AM
|
Junior Member
203 posts Joined: Jan 2003 From: KL / PJ / LYP / IMBI
|
QUOTE(k8118k @ Jul 30 2007, 01:02 AM) how to go to 36. 400 x9 = 3.6ghz mine now 3.2 on 400 x8 remember to add vcore  |
|
|
Jul 30 2007, 02:15 AM
|
|
Senior Member
3,658 posts Joined: Jan 2003
|
QUOTE(kvmcom @ Jul 30 2007, 02:13 AM) 400 x9 = 3.6ghz vcore set to 1.5 ady..remember to add vcore cant boot |
|
|
Jul 30 2007, 09:23 PM
|
Senior Member
4,717 posts Joined: Jan 2003
|
yo bro...
i'm getting 3.2Ghz speed very stable at stock voltage of 1.35V...so probably if you want to lower your temp, try use 1.35V instead of 1.375V... and also, at full load, i'm getting 75+deg'C as well... but if i blast full fan speed at my casing and also on the air cond, i can get around 5degC improvement or more... and i'm not using WC... just normal air cooling... QUOTE(TaiZi@CCF @ Jul 26 2007, 12:20 AM) I need all the guru to help me..... I dont know why, I got my Q6600 today, tested all stable, duo orthos full 4 core prime stable for more than 1 hours, I overclocked to only 3.2GHz with 1.375v. but why the hell my Q6600 running so hot??? I cant believe it how come irenic can get 65c full load at 1.55v.... please tell me why... getting mad.
Added on July 30, 2007, 9:25 pmyup... my TAT and core temp about the same...give them a tolerance about +/- 2degC can already...hehe.... QUOTE(§layerXT @ Jul 27 2007, 11:28 PM) Someone already compared Coretemp with TAT and the temp is very similar. TAT is build by Intel and this cant be wrong. This post has been edited by kevyeoh: Jul 30 2007, 09:25 PM |
|
|
Jul 30 2007, 10:57 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Ur one extreme edition maybe can use 1.35. Non extreme maybe need higher.
|
|
|
Jul 31 2007, 11:05 AM
|
Senior Member
3,239 posts Joined: Jun 2005
|
QUOTE(kmarc @ Jul 27 2007, 11:28 AM) Are you sure about this? I've been wondering about speedfan's reading too. There are usually a few readings showing in speedfan. CPU temp (only know if I correlate this temp reading with other software), Core0 temp and core1 temp. The CPU temp is usually about 6'c higher than the core0 and core1......... weird. my CPU temp show 38C while CPU#1 show 85C and CPU#2 86C lol. i think my CPU internal diode go haywire already. when full load, CPU#1 and CPU#2 only increase few Celsius only haha.so many using quad, itchy to try one too. next week might try it with my friends built |
|
|
Jul 31 2007, 11:30 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(toughnut @ Jul 31 2007, 11:05 AM) weird. my CPU temp show 38C while CPU#1 show 85C and CPU#2 86C lol. i think my CPU internal diode go haywire already. when full load, CPU#1 and CPU#2 only increase few Celsius only haha. So far, while researching on inaccurate core temp readings on the E6x50 series, I came across some discussion on the Q6600 CPUs too. Apparently, the newer Q6600 with G0 stepping has a higher Tjunction of 100'c instead of 85'c. As such, you're supposed to add another 15'c to your core temperature reading.so many using quad, itchy to try one too. next week might try it with my friends built The reason for this is because some 3rd party apps calculate core temp by using the Tjunction. So, if the Tjunction is different, so will the core temperature readings. I'm not too sure about the Q6600's problem as I've been reading up on the E6x50 series. Here's my thread. There are some links there..... problem still not resolved... http://forum.lowyat.net/topic/496060 |
|
|
Jul 31 2007, 12:32 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
not really, my current Q6600 with B3 stepping also showing Tjunction of 100C on coretemp.
how about other's Q6600? Tjunction 85C or 100C? |
|
|
Jul 31 2007, 05:29 PM
|
 
Staff
9,417 posts Joined: Jan 2003 From: Bladin Point, Northern Territory
|
Going to WC my Q6600 after i get my Ballistix RAMs, just got me some cheap vinyl tubes, so i'm testing the loop. Hopefully will be getting around 50c on load, and 30 something once i get a nice Thermochill.
|
|
|
Jul 31 2007, 10:16 PM
|
|
Senior Member
4,717 posts Joined: Jan 2003
|
i got a friend who tried water cooling on quad core... giving about minimum 7'C improvement compare to my air cooling using zalman heatsink...
|
|
|
Aug 1 2007, 12:23 AM
|
|
Staff
9,417 posts Joined: Jan 2003 From: Bladin Point, Northern Territory
|
QUOTE(kevyeoh @ Jul 31 2007, 10:16 PM) i got a friend who tried water cooling on quad core... giving about minimum 7'C improvement compare to my air cooling using zalman heatsink... Further improvement should be possible assuming he used a basic kit.Now planning to use the below in search for a quadcore superclock suicide run. - Liquid Metal TIM (Coolabratories) - Zerex 50/50 with Distilled water - Thermochill PA120.3 (maybe i'll dunk it in ice) - Secondary pump...who knows, maybe a D5 My mission is 4ghz for 4 cores Here's my lahling in loop testing  |
|
|
Aug 1 2007, 12:27 AM
|
Senior Member
1,561 posts Joined: Jan 2003 From: 秋葉原電気街 
|
omg sifu empire is back in the actions
welcome back! |
|
|
Aug 1 2007, 09:57 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Waiting for result & benchies. cool empire!
|
|
|
Aug 2 2007, 04:09 PM
|
|
Senior Member
3,239 posts Joined: Jun 2005
|
empire strike back...
damn expensive stuff. not for kids. btw, where to get that TIM? price? |
|
|
Aug 3 2007, 08:27 PM
|
|
Senior Member
4,717 posts Joined: Jan 2003
|
hehe... water cooling is way over my budget now...so stick to air cooling first...wait for empire's result and see if it's worth the money to bunk in...
hehe |
|
|
Aug 3 2007, 10:47 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
If quad core 4GHz stable on standard WC already very happy lor.
|
|
|
Aug 4 2007, 01:39 AM
|
|
Staff
9,417 posts Joined: Jan 2003 From: Bladin Point, Northern Territory
|
Heard Storm88 is at the hospital due to his wifey giving birth, or so i heard lah, so getting that new thermochill is going to take time.
My Windows Vista generously donated by Jinaun has been lost in the mail. Great fking job Posmalaysia, i bloody love you guys. No point waiting, knowing Malaysian regular post. My RAMs got delayed by Crucial due to a bad batch so remanufacturing was in order. Crap. Should be here by next week. Atleast my MOSFET coolers from Hwoarang45 should arrive with the rest of the above on monday and tuesday. Need to keep the 680i cool before i can do any clocking. Mouser electronics is delaying my shipment of Silver Micas from Cornell Dubilier, Bourns Trimpots and AVX wet slug tantalums due to stock issue....WTF. Damn, everything is late! |
|
|
Aug 4 2007, 01:45 AM
|
|
Junior Member
203 posts Joined: Jan 2003 From: KL / PJ / LYP / IMBI
|
my test sys
ip35-pro cooler gm2+3fan traser 8500 500w enemax 2600xtx ddr4 easy go 4core 4g still at stb test :....wait Attached thumbnail(s) 
|
|
|
Aug 4 2007, 01:49 AM
|
Senior Member
1,201 posts Joined: Dec 2004 From: Kuala Lumpur
|
QUOTE(empire23 @ Aug 4 2007, 01:39 AM) Heard Storm88 is at the hospital due to his wifey giving birth, or so i heard lah, so getting that new thermochill is going to take time. Bro, if you planning to cool your CPU only. You certainly dont need a Thermochill as there is almost no difference in performance if u compare between a normal switech double rad to Thermochill PA120.3. Kind of overkill. My Windows Vista generously donated by Jinaun has been lost in the mail. Great fking job Posmalaysia, i bloody love you guys. No point waiting, knowing Malaysian regular post. My RAMs got delayed by Crucial due to a bad batch so remanufacturing was in order. Crap. Should be here by next week. Atleast my MOSFET coolers from Hwoarang45 should arrive with the rest of the above on monday and tuesday. Need to keep the 680i cool before i can do any clocking. Mouser electronics is delaying my shipment of Silver Micas from Cornell Dubilier, Bourns Trimpots and AVX wet slug tantalums due to stock issue....WTF. Damn, everything is late! If u really want a thermochill and reach your doorstep fast, order it from DangerDen. Will reach your doorstep in 4 working days if u use EMS. hehe |
|
|
Aug 4 2007, 01:53 AM
|
|
Senior Member
1,201 posts Joined: Dec 2004 From: Kuala Lumpur
|
Can prime stable at 4ghz?
 Anyway your temp is nice at 1.52vcore / air. |
|
|
Aug 4 2007, 01:57 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
Are you using core temp? Either v0.94 or 0.95? Interested to know what the Tjunction is. Supposed to be 100'c.
Anyway, nice OC! |
|
|
Aug 4 2007, 02:00 AM
|
|
Junior Member
203 posts Joined: Jan 2003 From: KL / PJ / LYP / IMBI
|
QUOTE(kmarc @ Aug 4 2007, 01:57 AM) Are you using core temp? Either v0.94 or 0.95? Interested to know what the Tjunction is. Supposed to be 100'c. cpu cool only ....thxstill under test ...wait .... Anyway, nice OC! |
|
|
Aug 4 2007, 02:01 AM
|
Senior Member
628 posts Joined: Oct 2006
|
WOW... windows xp can support n utilise all 4 cores...??? 39 degree...!!! very aMAXing...
|
|
|
Aug 4 2007, 02:06 AM
|
|
Junior Member
203 posts Joined: Jan 2003 From: KL / PJ / LYP / IMBI
|
 vdroop +.07 bios set 1.58 only show 1.52/1 only This post has been edited by kvmcom: Aug 4 2007, 02:32 AM |
|
|
Aug 4 2007, 02:26 AM
|
|
Senior Member
835 posts Joined: Sep 2004 From: LYP@Bintang Walk
|
WOW.........4GHZ on air
Can't wait to OC mine later........ |
|
|
Aug 4 2007, 02:27 AM
|
|
Senior Member
1,201 posts Joined: Dec 2004 From: Kuala Lumpur
|
Abit Ip35 pro got that serious vdroop?
hmmmm.... |
|
|
Aug 4 2007, 02:43 AM
|
|
Junior Member
203 posts Joined: Jan 2003 From: KL / PJ / LYP / IMBI
|
[quote=irangan,Aug 4 2007, 02:27 AM]
Abit Ip35 pro got that serious vdroop? 4m cpu 2-3v 8m cpu 5-6 v ? how about another mobo..?  tis station test with my c4q66 go .....2moro try post another result wait 4 irenic/rlhc put more xtreme result....... |
|
|
Aug 4 2007, 03:27 AM
|
|
Staff
9,417 posts Joined: Jan 2003 From: Bladin Point, Northern Territory
|
QUOTE(irangan @ Aug 4 2007, 01:49 AM) Bro, if you planning to cool your CPU only. You certainly dont need a Thermochill as there is almost no difference in performance if u compare between a normal switech double rad to Thermochill PA120.3. Kind of overkill. Well this has 4 cores instead of the usual 2, so i'd appreciate any increase in delta and possible heat saturation levels possible If u really want a thermochill and reach your doorstep fast, order it from DangerDen. Will reach your doorstep in 4 working days if u use EMS. hehe Plus i might as well dunk it into ice for better peformance or use it as a heat transfer mechnanism for a possible evaporator, depending on how much cooling i need done, although an IHS lap would be a first solution. Shawty is donating some MX-2, which has superb thermal characteristics, all in all this is going to be an interesting first foray into WCing. Although the Storm G4 is not suited for quad core use, for now, i guess she'll have to hold Checked Dangerden, no stock..... This post has been edited by empire23: Aug 4 2007, 03:27 AM |
|
|
Aug 4 2007, 10:16 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Owh, ip35pro version dont have backplate led like ab9 QuadGT kah?..
|
|
|
Aug 4 2007, 10:18 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
@kvmcom
No way! You're using the large CPU heatsink!!!  What do you call that heatsink again? How much does it cost anyway?No wonder your CPU is so cool!!! I see you only put the sponge (the sponge came with the mobo right?) below the mobo. Is that safe? Any heat build-up? This post has been edited by kmarc: Aug 4 2007, 10:19 AM |
|
|
Aug 4 2007, 10:28 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Last time shawty only got 1 left... I bet sold already kah...
|
|
|
Aug 4 2007, 11:08 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Its cm gemini which quite had good reputation. While irenic has been using it to oc his quad core kaw2 b4.
|
|
|
Aug 4 2007, 11:23 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(§layerXT @ Aug 4 2007, 11:08 AM) Its cm gemini which quite had good reputation. While irenic has been using it to oc his quad core kaw2 b4. OIC. That's the gemini 2. It looks real big. Mistaken it for the new HSF which was recently shown in a exhibition in Taiwan, I think.... |
|
|
Aug 4 2007, 12:48 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
sorry guys i couldnt manage to test the oc potential of this GO yet coz my p35t dq6 and B3 just died..
btw here is the stock screenshot .. tested the G0 at Ataris place q6600 go stock e2160 heatsink gigabyte p35 ds3 gigabyte 550w odin pro 2x 1gb kvr ddr2 667 
This post has been edited by irenic: Aug 4 2007, 12:49 PM |
|
|
Aug 4 2007, 01:22 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Using stock 2160 heatsink? Is it the same? I think quad core hsf much better characteristic to protect q6600.
|
|
|
Aug 5 2007, 11:14 AM
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
irenic: Post some oc's results lah
Tempting lar.... |
|
|
Aug 5 2007, 11:33 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
well after some hardmod, i manage to bring my p35t dq6 to alive again!
but kinda bz today.. most probably will start oc this thing tomorow |
|
|
Aug 5 2007, 01:07 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Would u think this will applies on budget P35-DS3 too?
|
|
|
Aug 5 2007, 04:14 PM
|
Junior Member
324 posts Joined: Jan 2003 From: Deserts of Kedah
|
ermm..noob question..mobo must support quad core ah?mine support onli duo core..can i use quad?
|
|
|
Aug 5 2007, 06:51 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Please check Asus website for processor compatibility.
|
|
|
Aug 5 2007, 07:36 PM
|
 
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
Just got my Q6600 up and running, cooled by an Ultra 120 Extreme and a low cfm Delta fan. At 2.6Ghz full load, Core temp shows 84c/83c/78c/79c for the 4 cores while Easy Tune shows 61c
|
|
|
Aug 5 2007, 07:40 PM
|
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
QUOTE(arj @ Aug 5 2007, 07:36 PM) Just got my Q6600 up and running, cooled by an Ultra 120 Extreme and a low cfm Delta fan. At 2.6Ghz full load, Core temp shows 84c/83c/78c/79c for the 4 cores while Easy Tune shows 61c Is your Q6600 Rev. B3? That's hot... |
|
|
Aug 5 2007, 08:19 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(tAmp0i @ Aug 5 2007, 07:40 PM) Is your Q6600 Rev. B3? That's hot... Yup, it's a B3. |
|
|
Aug 5 2007, 08:25 PM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(arj @ Aug 5 2007, 07:36 PM) Just got my Q6600 up and running, cooled by an Ultra 120 Extreme and a low cfm Delta fan. At 2.6Ghz full load, Core temp shows 84c/83c/78c/79c for the 4 cores while Easy Tune shows 61c Oopss..... your's a B3 stepping....What does core temp show for your tjunction? This post has been edited by kmarc: Aug 5 2007, 08:30 PM |
|
|
Aug 5 2007, 08:38 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(kmarc @ Aug 5 2007, 08:25 PM) Oopss..... your's a B3 stepping.... The tjunction temp is 100c.What does core temp show for your tjunction? |
|
|
Aug 5 2007, 08:57 PM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(arj @ Aug 5 2007, 08:38 PM) The tjunction temp is 100c. Weird. Then it's correct (B3 has a tjunction of 100'c). By right core temp should be indicating the correct temperature.Have you tried Intel's TAT (thermal analysis tool) It's supposed to be other apps that reads the temperature wrongly. See this : http://www.boogleoogle.co.uk/category/hardware/ You sure your HSF is seated properly? We need a quad expert here!!!!  |
|
|
Aug 5 2007, 09:31 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(arj @ Aug 5 2007, 07:36 PM) Just got my Q6600 up and running, cooled by an Ultra 120 Extreme and a low cfm Delta fan. At 2.6Ghz full load, Core temp shows 84c/83c/78c/79c for the 4 cores while Easy Tune shows 61c time to move bro! get those phase change la |
|
|
Aug 5 2007, 10:13 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
I'm at 2.8Gghz right now, highest coretemp is 90c while eazy tune shows 70c. I've reinstalled the heatsink already. The weird thing is that when I touched the lower part of the heatsink while under full load, it's not even warm!
QUOTE(gengstapo @ Aug 5 2007, 09:31 PM) time to move bro! get those phase change la Still too lazy to install my Prommy |
|
|
Aug 5 2007, 10:16 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Thats quite hot @ 2.6GHz and cannot blame 100% on B3 stepping maybe air ventilation not so good.
|
|
|
Aug 5 2007, 10:16 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(arj @ Aug 5 2007, 10:13 PM) I'm at 2.8Gghz right now, highest coretemp is 90c while eazy tune shows 70c. I've reinstalled the heatsink already. The weird thing is that when I touched the lower part of the heatsink while under full load, it's not even warm! might a bug i think.. zZZzz Still too lazy to install my Prommy if not even warm, then its ok de |
|
|
Aug 5 2007, 11:26 PM
|
|
Senior Member
4,717 posts Joined: Jan 2003
|
if it's not even warm...means the heat transfer no good la...
QUOTE(arj @ Aug 5 2007, 10:13 PM) I'm at 2.8Gghz right now, highest coretemp is 90c while eazy tune shows 70c. I've reinstalled the heatsink already. The weird thing is that when I touched the lower part of the heatsink while under full load, it's not even warm! Still too lazy to install my Prommy |
|
|
Aug 5 2007, 11:49 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(kevyeoh @ Aug 5 2007, 11:26 PM) if it's not even warm...means the heat transfer no good la... I've tried reinstalling it already, the outline on the base of the heatsink shows that there's proper contact. I'm currently using the Thermalright Ultra 120 Extreme, turned the screws all the way down already. Will do it again tomorrow. Might also try using the stock heatsink for comparison. |
|
|
Aug 6 2007, 01:32 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
hi, just wanna share some idle temps of this g0 q6600 under water..
setup: c2d q6600 g0 L72.. gigabyte p35t dq6 2x 1gb kingston hyperx ddr3 hd 2900xt 1gb ddr4 cooltrek radiator 1203, dtek fuzion cpu waterblock, laing d5 pump, distilled water corsair hx620w Q6600 g0 idle temp @ stock  Q6600 g0 idle temp @ 4.05ghz 1.6vcore  Q6600 g0 idle temp @ 4.14ghz 1.65vcore  |
|
|
Aug 6 2007, 02:35 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
now is load temp for this q6600 g0 under water..
occt 15mins @ 1.475vcore 3.7ghz..   This post has been edited by irenic: Aug 6 2007, 02:44 AM |
|
|
Aug 6 2007, 12:17 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
why the z-cpu's voltage is always 1.138???
|
|
|
Aug 6 2007, 12:23 PM
|
|
Senior Member
3,658 posts Joined: Jan 2003
|
how to set my spec break 3.2
i now stuck at 3.2ghz(400x8) cant go 3.6 .zzzzz i also wonder y my ddr2 hyperx 800 shown 667 only..... even all packaging and sticker is 6400.....zzz...help brother kvmcom and others... |
|
|
Aug 6 2007, 01:00 PM
|
|
Junior Member
367 posts Joined: Jan 2003 From: Boleh Land
|
QUOTE(arj @ Aug 5 2007, 10:13 PM) I'm at 2.8Gghz right now, highest coretemp is 90c while eazy tune shows 70c. I've reinstalled the heatsink already. The weird thing is that when I touched the lower part of the heatsink while under full load, it's not even warm! you have the same exact problem like me....Still too lazy to install my Prommy have you tried stock heatshink? |
|
|
Aug 6 2007, 02:29 PM
|
|
Senior Member
3,658 posts Joined: Jan 2003
|
haha
u all also same wit mine speed fan show 40+_ tat sho 59-60...... y? Added on August 6, 2007, 4:22 pmanother question is y after certain time use... when click shutdown.... pc didnt responce... need ctrl_alt_del open task manager to shut it down..... sien lar... This post has been edited by k8118k: Aug 6 2007, 04:22 PM |
|
|
Aug 6 2007, 09:23 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
@k8118k.
maybe ur oc not stable enuff? or it also happen at stock clock? neway my latest 3dmark06 journey.. Score : 13603 CPU : Intel C2D Q6600 @ 4Ghz (d-tek fuzion) M/B : Gigabyte p35t dq6 bios F3i RAM : 2 x 1024MB kingston hyperX ddr3 1350mhz 7-7-7-21 G/C : HIS 2900XT 1gb 855/1110 Driver : Catalyst 7.7 Mod : none  and here is the comparison between E6850 @ 4ghz and Q6600 @ 4ghz.. but the q6600 2900xt is clocked at 855/1110 compared to e6850's 850/1100  |
|
|
Aug 7 2007, 03:44 PM
|
Senior Member
1,414 posts Joined: Feb 2006 From: Bandar Tun Razak, KL
|
Mine with air cooling (Thermatake BTVX)...
Closed case CM Stacker... Vcore at bios 1.4V Load temp around 62c, Idle temp around 50c...  This post has been edited by norazwan79: Aug 7 2007, 05:52 PM |
|
|
Aug 7 2007, 06:30 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
Where are you guys getting the G0s?
|
|
|
Aug 7 2007, 06:42 PM
|
|
Junior Member
302 posts Joined: Jun 2007 From: Johor
|
QUOTE(arj @ Aug 7 2007, 06:30 PM) Where are you guys getting the G0s? Kvmcom is selling some of them in garage sales |
|
|
Aug 7 2007, 08:38 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
i using B3, but tot of getting G0, but since penryn is so near.. i think i'll wait.. LOL
|
|
|
Aug 7 2007, 11:29 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Read from HKPC the temperature very cool meh, even full load under 40c
|
|
|
Aug 8 2007, 08:24 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
just went to mypc, i asked their salesman, they already have the G0 in stocks
yummy..... |
|
|
Aug 8 2007, 08:54 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
Got myself a G0 earlier today, installed it already. Core Temp and Easy Tune now shows the same temp
Gonna do some overclocking now, see if it's any better than my B3 **EDIT** Scrap that, saw the temps wrongly. There's still a 10c difference between the two, it's just that the numbers are lower compared to B3 At 3Ghz, core temp shows idle around 45c and full load around 55c This post has been edited by arj: Aug 8 2007, 09:20 PM |
|
|
Aug 8 2007, 09:23 PM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(arj @ Aug 8 2007, 08:54 PM) Got myself a G0 earlier today, installed it already. Core Temp and Easy Tune now shows the same temp Great news!!! Make sure you OC kaw kaw till 4 Ghz!!! Gonna do some overclocking now, see if it's any better than my B3 **EDIT** Scrap that, saw the temps wrongly. There's still a 10c difference between the two, it's just that the numbers are lower compared to B3 At 3Ghz, core temp shows idle around 45c and full load around 55c So what happened to your B3? |
|
|
Aug 8 2007, 11:10 PM
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(jinaun @ Aug 8 2007, 08:24 PM) just went to mypc, i asked their salesman, they already have the G0 in stocks how much r they selling?yummy..... QUOTE(arj @ Aug 8 2007, 08:54 PM) Got myself a G0 earlier today, installed it already. Core Temp and Easy Tune now shows the same temp what cooling r using bro?seems the delta between idle and load is very good...only 10c... Gonna do some overclocking now, see if it's any better than my B3 **EDIT** Scrap that, saw the temps wrongly. There's still a 10c difference between the two, it's just that the numbers are lower compared to B3 At 3Ghz, core temp shows idle around 45c and full load around 55c |
|
|
Aug 8 2007, 11:24 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
QUOTE(remysix @ Aug 8 2007, 11:10 PM) how much r they selling? 980 i think.. or maybe lower.. try bargaining wit them.. see what they can offer uThis post has been edited by jinaun: Aug 8 2007, 11:25 PM |
|
|
Aug 9 2007, 12:22 AM
|
Senior Member
879 posts Joined: Jan 2003
|
Im planning to get the G0 so guys if can help out please state which shop is selling it.. preferably in Lowyat Plaza .
Thanks! |
|
|
Aug 9 2007, 01:49 AM
|
|
Junior Member
49 posts Joined: Oct 2006
|
My new Q6600 SLACR L718A245
Idle  4 threads full load  |
|
|
Aug 9 2007, 06:22 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(jinaun @ Aug 8 2007, 11:24 PM) 980 i think.. or maybe lower.. try bargaining wit them.. see what they can offer u just wanna know the price...if u notice my siggy, already own one |
|
|
Aug 9 2007, 07:17 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
This will be my 24/7 Folding settings
  Added on August 9, 2007, 8:35 pm QUOTE(remysix @ Aug 8 2007, 11:10 PM) what cooling r using bro?seems the delta between idle and load is very good...only 10c... Thermalright Ultra 120 Extreme This post has been edited by arj: Aug 9 2007, 08:35 PM |
|
|
Aug 9 2007, 09:30 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(arj @ Aug 9 2007, 07:17 PM) This will be my 24/7 Folding settings sweet, what the vcore & RAM timing applied there? Added on August 9, 2007, 8:35 pm Thermalright Ultra 120 Extreme This post has been edited by gengstapo: Aug 9 2007, 10:07 PM |
|
|
Aug 9 2007, 10:28 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(gengstapo @ Aug 9 2007, 09:30 PM) sweet, what the vcore & RAM timing applied there? 1.475v in bios if I'm not mistaken. Lazy to play around with the ram so I just put it at auto After reading what the other G0s can do at XS, I've increasing the speed summore. Now at 3.55Ghz 1.525v, will keep on increasing them until I hit 70c This post has been edited by arj: Aug 9 2007, 10:29 PM |
|
|
Aug 9 2007, 11:48 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
very good OC result, check tiramitsu's post
http://www.overclock.net/intel-cpus/214785...q6600-g0-2.html |
|
|
Aug 9 2007, 11:59 PM
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
q6600 G0 stepping can be better oc and gaming for e6850? how far can this q6600 with G0 stepping can go with air cooling??
This post has been edited by intothefantasy: Aug 10 2007, 12:08 AM |
|
|
Aug 10 2007, 05:02 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intothefantasy @ Aug 9 2007, 11:59 PM) q6600 G0 stepping can be better oc and gaming for e6850? how far can this q6600 with G0 stepping can go with air cooling?? i think it shall depend on stepping & LUCK again btw, does any1 here overclocking this quad-cores with p965 chippy? does the result nice? |
|
|
Aug 10 2007, 07:21 AM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
Q6600 Update: Currently stable at 3.6Ghz with 1.625v in bios, temp hovering around 70c
QUOTE(intothefantasy @ Aug 9 2007, 11:59 PM) q6600 G0 stepping can be better oc and gaming for e6850? how far can this q6600 with G0 stepping can go with air cooling?? At stock speed the E6850 has an edge in gaming but when overclocking comes into play I believe the difference is negligeable and barely noticeable. Check out my results, I'm using Thermalright Ultra 120 Extreme with a low noise Thermaltake fan |
|
|
Aug 10 2007, 09:05 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
^err boss, u board using what chipset, p53 ka??
the prime95 has extra feat. ka like orthos when it comes to fail, got sound?? |
|
|
Aug 10 2007, 09:27 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
QUOTE(gengstapo @ Aug 10 2007, 05:02 AM) i think it shall depend on stepping & LUCK again Yeah, anyone bought Q6600 G0 and oc on 965P shipset? btw, does any1 here overclocking this quad-cores with p965 chippy? does the result nice? |
|
|
Aug 10 2007, 09:45 AM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(gengstapo @ Aug 10 2007, 09:05 AM) ^err boss, u board using what chipset, p53 ka?? I'm using P35. When one of the cores fail in Prime95, the icon will turn red.the prime95 has extra feat. ka like orthos when it comes to fail, got sound?? |
|
|
Aug 10 2007, 10:31 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(arj @ Aug 10 2007, 09:45 AM) I'm using P35. When one of the cores fail in Prime95, the icon will turn red. ahh ic, so basically, p35 more suit when paired with quaddies rather than p965(what im using)p965 can support nicely when running on default & mild setup, but when it comes to higher clocks, it becomes unstable no matter what setting applied hurmm am i going to get p35 boards??  about the prime95, so it doesnt have a "beep" sound ait?? in that case, have to turn on my display at least 8hrs to monitor the overclocking progress This post has been edited by gengstapo: Aug 10 2007, 10:33 AM |
|
|
Aug 10 2007, 10:41 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(arj @ Aug 10 2007, 07:21 AM) Q6600 Update: Currently stable at 3.6Ghz with 1.625v in bios, temp hovering around 70c Is there a reason why you choose 70'c as the highest core temp?At stock speed the E6850 has an edge in gaming but when overclocking comes into play I believe the difference is negligeable and barely noticeable. Check out my results, I'm using Thermalright Ultra 120 Extreme with a low noise Thermaltake fan I know the Q6600 has a better thermal profile but AFAIK, most people would recommend a max temp of 60'c for the C2D. |
|
|
Aug 10 2007, 01:07 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
@gengstapo, what 965P board did u used to oc Q6600?
|
|
|
Aug 10 2007, 02:46 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(kmarc @ Aug 10 2007, 10:41 AM) Is there a reason why you choose 70'c as the highest core temp? For me 70c is a number that I'm comfortable with running 24/7. Have done that with my previous processors as well. Running it at such high temp might reduce its lifespan but nowadays the processor will get obsolete first before dying I know the Q6600 has a better thermal profile but AFAIK, most people would recommend a max temp of 60'c for the C2D. |
|
|
Aug 10 2007, 02:53 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(§layerXT @ Aug 10 2007, 01:07 PM) @gengstapo, what 965P board did u used to oc Q6600? im still using my old board, previously paired with e66 & now q66its the commando board.. ps: at the moment still stressing for atleast 2hrs stable, 312Mhz x 9..  zZZzzThis post has been edited by gengstapo: Aug 10 2007, 02:54 PM |
|
|
Aug 10 2007, 03:56 PM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
QUOTE(arj @ Aug 10 2007, 02:46 PM) For me 70c is a number that I'm comfortable with running 24/7. Have done that with my previous processors as well. Running it at such high temp might reduce its lifespan but nowadays the processor will get obsolete first before dying OIC. You mean that your previous C2D was also running at 70'c??I'm already when my proc is running at 60'C!!!  I guess I can push my proc further as previous E6x00 had a thermal specification of 62'c whereas the new E6x50 has a higher level at 71'c!  |
|
|
Aug 10 2007, 04:36 PM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(kmarc @ Aug 10 2007, 03:56 PM) OIC. You mean that your previous C2D was also running at 70'c?? This is my first Intel processor in years. My previous processor was an AMD Opteron 165.I'm already when my proc is running at 60'C!!! I guess I can push my proc further as previous E6x00 had a thermal specification of 62'c whereas the new E6x50 has a higher level at 71'c! |
|
|
Aug 10 2007, 09:31 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
QUOTE(gengstapo @ Aug 10 2007, 02:53 PM) im still using my old board, previously paired with e66 & now q66 Asus Comando only capable of 312MHz? its the commando board.. ps: at the moment still stressing for atleast 2hrs stable, 312Mhz x 9.. zZZzz This post has been edited by §layerXT: Aug 10 2007, 09:41 PM |
|
|
Aug 10 2007, 09:42 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(§layerXT @ Aug 10 2007, 09:31 PM) Asus Comando only capable of 312MHz? nahh, lastime with my e66, it can do atleast 480Mhzi think p965 not the exact match with quad cores This post has been edited by gengstapo: Aug 10 2007, 09:43 PM |
|
|
Aug 10 2007, 09:47 PM
|
Senior Member
905 posts Joined: Aug 2006
|
I think the best mobo for quaddies is still those intel P35's...my 680i cant run quadies past 390FSB....now need to fork out for a P35...darn...whats the recommended P35 mobo?
|
|
|
Aug 10 2007, 11:49 PM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(gengstapo @ Aug 10 2007, 02:53 PM) im still using my old board, previously paired with e66 & now q66 its the commando board.. ps: at the moment still stressing for atleast 2hrs stable, 312Mhz x 9.. zZZzz tukar trus quad ek bro u use wat bios?even latest bios cant fix it?wahlioa..xkan nk kena beli mobo lain kot |
|
|
Aug 11 2007, 12:01 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(mfcm @ Aug 10 2007, 11:49 PM) tukar trus quad ek bro u use wat bios?even latest bios cant fix it?wahlioa..xkan nk kena beli mobo lain kot no proc to useakuk flash to latest bios 1404 kalau tak silap |
|
|
Aug 11 2007, 12:31 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
The commando known priced 4 figure last time and when P35 came out now become useless(quad core oc)... Oh god, thats why sumtimes just hate new technology, p965 not even last a year & then P35 was out.
|
|
|
Aug 11 2007, 12:37 AM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(gengstapo @ Aug 11 2007, 12:01 AM) hehee.. tak bole nak buat aper daa, e66 sudah juai wah..;atest bios pn xle fix..then watse if got gud proc but cant oc kaw kaw no proc to useakuk flash to latest bios 1404 kalau tak silap thinkin to get quad oso..haha but now need to KIV 1t since p965 so perfome well with it  |
|
|
Aug 11 2007, 01:07 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(mfcm @ Aug 11 2007, 12:37 AM) wah..;atest bios pn xle fix..then watse if got gud proc but cant oc kaw kaw releks br0, need no w0rry thinkin to get quad oso..haha but now need to KIV 1t since p965 so perfome well with it i still doing some tweaking upon my rig.. |
|
|
Aug 11 2007, 10:17 AM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
  |
|
|
Aug 11 2007, 10:20 AM
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(arj @ Aug 11 2007, 10:17 AM) Impressive. |
|
|
Aug 11 2007, 08:31 PM
|
|
Senior Member
905 posts Joined: Aug 2006
|
arj, what mobo are you using? I'm thinking of grabbing the p5k premium, anyone know if any shops in lyp are selling this mobo?
Added on August 11, 2007, 8:36 pmjust read that x38 based mobo's are out in sept 07... thats just next month..might as well hang on for a while more... This post has been edited by BurgerRI: Aug 11 2007, 08:36 PM |
|
|
Aug 12 2007, 01:38 AM
|
|
VIP
4,896 posts Joined: Jan 2003 From: Kg Sg Penchala, KL
|
QUOTE(BurgerRI @ Aug 11 2007, 08:31 PM) arj, what mobo are you using? I'm thinking of grabbing the p5k premium, anyone know if any shops in lyp are selling this mobo? I'm using the Gigabyte P35 DS3.Added on August 11, 2007, 8:36 pmjust read that x38 based mobo's are out in sept 07... thats just next month..might as well hang on for a while more... |
|
|
Aug 12 2007, 08:48 AM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
well...my P35-DQ6 is Quadcore optimized...i'm not sure whether gigabyte means the board or actually the P35 is quadcore optimized...currently running OCCT at 3.4G@1.375v, drooped to 1.344vcore...load temp is around 53-55c...love it...
i'm looking at 3.6G on daily setup...hope can do that...just installed the xigmatek s1283 last nite...the performance, it's far better than my geminiII Added on August 12, 2007, 9:24 am QUOTE(sHawTY @ Aug 11 2007, 10:20 AM) Q6600 with G0 stepping eyh? bro...angkat la the Quad G0...with ur WC setup...hitting a >4G is do-able...4 cores at 4G...last time cannot imagine it...now, it's a achievable...Impressive. Standard 2 of Primary School caclulation: 1 Core = 4Ghz 4 Core = 4 x 4 Ghz = 16Ghz This post has been edited by remysix: Aug 12 2007, 09:26 AM |
|
|
Aug 12 2007, 09:26 AM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
Xigmatek S-1283 can be better then ultra 120 extreme ar?
|
|
|
Aug 12 2007, 09:38 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
@remysix
hehee.. nice setup & result there, wish u able to get the 3.6Ghz atleast, higher would be greater ive seen that p35 chipset was mean to be quad-cores mate, very cun i believe it is possible to get higher OC result at default stock voltage This post has been edited by gengstapo: Aug 12 2007, 09:39 AM |
|
|
Aug 12 2007, 10:46 AM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
yups.. in terms of quad core overclocking, p35 is if not better but on par with 680i chipset.. which is far better than 965 and of coz 975..
and what makes p35 better than its 680i is the simplicity.. no need painful tweaking like the nforce one.. so gengstapo, bile lagi :-" |
|
|
Aug 12 2007, 10:53 AM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(irenic @ Aug 12 2007, 10:46 AM) so gengstapo, bile lagi :-" Gengstapo cakap dulu dia dah retire from overclocking.Let's see sampai bila dia boleh lari dari temptation of overclocking. |
|
|
Aug 12 2007, 11:07 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(arj @ Aug 11 2007, 10:17 AM) |
|
|
Aug 12 2007, 11:47 AM
|
|
Senior Member
905 posts Joined: Aug 2006
|
[quote=remysix,Aug 12 2007, 08:48 AM]
well...my P35-DQ6 is Quadcore optimized...i'm not sure whether gigabyte means the board or actually the P35 is quadcore optimized...currently running OCCT at 3.4G@1.375v, drooped to 1.344vcore...load temp is around 53-55c...love it... i'm looking at 3.6G on daily setup...hope can do that...just installed the xigmatek s1283 last nite...the performance, it's far better than my geminiII Hey remy, you should be able to hit 4.0Ghz weith your DQ6...go for it...up the fsb |
|
|
Aug 12 2007, 11:51 AM
|
|
Elite
14,576 posts Joined: May 2006 From: Sarawak
|
@ remysix
Wow! Nice temps for Quad. What is the difference in temps comparing the Xigmatek to the GeminII? At idle and load? This post has been edited by kmarc: Aug 12 2007, 11:53 AM |
|
|
Aug 12 2007, 11:51 AM
|
|
Senior Member
905 posts Joined: Aug 2006
|
QUOTE(irenic @ Aug 12 2007, 10:46 AM) yups.. in terms of quad core overclocking, p35 is if not better but on par with 680i chipset.. which is far better than 965 and of coz 975.. Hmm...actually certain 680i mobo's is okay for quad core OC, but like irenic mentioned, it takes tweaking to get it running fine. and further more there are a couple of revisions of the 680i and so far i think only EVGA has released the tweaked version that supports OC'ing quadcore properly, their A1 rev...all the other 680i manufacturer's could give a rats ass abt newer revisions..even the asus striker extreme wont be able to OC quadies to their max potential. But for those brave enough, there is a V Gtl mod on the net for most 680i's.... and what makes p35 better than its 680i is the simplicity.. no need painful tweaking like the nforce one.. so gengstapo, bile lagi :-" This post has been edited by BurgerRI: Aug 12 2007, 11:52 AM |
|
|
Aug 12 2007, 12:27 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(irenic @ Aug 12 2007, 10:46 AM) yups.. in terms of quad core overclocking, p35 is if not better but on par with 680i chipset.. which is far better than 965 and of coz 975.. nah, not anywhere near future.. will wait for the right time and what makes p35 better than its 680i is the simplicity.. no need painful tweaking like the nforce one.. so gengstapo, bile lagi :-" neway, my quaddy running at 3.1Ghz with my p965 board currently, still in process of tweaking, who knows might get 3.4G/ 3.6G.. its g0od enuff i think QUOTE(sHawTY @ Aug 12 2007, 10:53 AM) Gengstapo cakap dulu dia dah retire from overclocking. w0ot, ko nieh sebok jerr.. ko amik lerr dulu Let's see sampai bila dia boleh lari dari temptation of overclocking. |
|
|
Aug 12 2007, 01:40 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(BurgerRI @ Aug 12 2007, 11:47 AM) Hey remy, you should be able to hit 4.0Ghz weith your DQ6...go for it...up the fsb actually, it has already hit 4G but wif geminiII...now i'm searching the daily running speed...so far, i can say that the s1283 is better than the geminiII...but unfortunately, i don have the figure to show it...last time running it with geminiII, dok dapat the 'crashed' je...maybe i put too much tim or something else... QUOTE(kmarc @ Aug 12 2007, 11:51 AM) @ remysix dun have the figure and screenie...but IIRC, it would be around 7-10c...but now my system temp is high...last time using geminiII...got 2x120mm pushing the air down and cooling the ram plus the surrounding...now i used 2x120mm, push and pull but towards the exhaust rear fan...so, the mobo area left un-cool...gotta do something about it...Wow! Nice temps for Quad. What is the difference in temps comparing the Xigmatek to the GeminII? At idle and load? This post has been edited by remysix: Aug 12 2007, 01:45 PM |
|
|
Aug 12 2007, 01:42 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(gengstapo @ Aug 12 2007, 12:27 PM) w0ot, ko nieh sebok jerr.. ko amik lerr dulu Taknak aku eyh, guna je la apa yang ada, nanti X38 kuar, ko tengok aku upgrade kaw kaw! |
|
|
Aug 12 2007, 01:44 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(irenic @ Aug 12 2007, 10:46 AM) yups.. in terms of quad core overclocking, p35 is if not better but on par with 680i chipset.. which is far better than 965 and of coz 975.. if i have a car that i can just step on the pad and it goes at the same speed with a car that has a cockpit like the plane - need to switch here and there, i would say the former is a better choice/performer...anyway, that maybe coming from ME who don have the skill in tweaking the mobo and what makes p35 better than its 680i is the simplicity.. no need painful tweaking like the nforce one.. so gengstapo, bile lagi :-" |
|
|
Aug 12 2007, 02:31 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
just passed 12hrs OCCT - 3.4Ghz@1.375v/1.344vdroop
just luv the temp  
|
|
|
Aug 12 2007, 02:43 PM
|
Elite
5,824 posts Joined: Jan 2003 From: Damansara Perdana
|
I bought arj's B3, currently doing 3Ghz, stock voltage and stock HSF. So far everything's stable, been running folding for 12 hours already. And, I'm not sure how reliable is lm sensors reading the core temp in Linux.
Below is the temp which I believe is inaccurate (fluctuates between 58C to 60C normally). QUOTE cn9ne@cn8ne:~/fold$ sensors it8718-isa-0290 Adapter: ISA adapter in0: +1.26 V (min = +0.00 V, max = +4.08 V) in1: +1.78 V (min = +0.00 V, max = +4.08 V) in2: +3.31 V (min = +0.00 V, max = +4.08 V) in3: +2.88 V (min = +0.00 V, max = +4.08 V) in4: +1.58 V (min = +0.00 V, max = +4.08 V) in5: +0.00 V (min = +0.00 V, max = +4.08 V) ALARM in6: +0.08 V (min = +0.00 V, max = +4.08 V) in7: +3.04 V (min = +0.00 V, max = +4.08 V) in8: +3.33 V fan1: 3000 RPM (min = 0 RPM) fan2: 1436 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) temp1: +50°C (low = +127°C, high = +127°C) sensor = thermistor temp2: +55°C (low = +127°C, high = +127°C) sensor = diode temp3: -1°C (low = +127°C, high = +127°C) sensor = thermistor vid: +0.000 V This post has been edited by c9: Aug 12 2007, 02:44 PM |
|
|
Aug 12 2007, 05:55 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
QUOTE(remysix @ Aug 12 2007, 01:44 PM) if i have a car that i can just step on the pad and it goes at the same speed with a car that has a cockpit like the plane - need to switch here and there, i would say the former is a better choice/performer...anyway, that maybe coming from ME who don have the skill in tweaking the mobo so do i .. no skill in tweaking a mobo so thats why never have interest in using nforce 680i sli board |
|
|
Aug 12 2007, 06:06 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(irenic @ Aug 12 2007, 05:55 PM) so do i .. no skill in tweaking a mobo haha.. but the old time when amd most choosen 1, u use dfi boards which comes with nforce chipset what? so thats why never have interest in using nforce 680i sli board or u being bZ currently coz always switching hardware?? |
|
|
Aug 12 2007, 07:44 PM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
QUOTE(gengstapo @ Aug 12 2007, 06:06 PM) haha.. but the old time when amd most choosen 1, u use dfi boards which comes with nforce chipset what? thats the answer...haha he got supported finance for the setup or u being bZ currently coz always switching hardware?? btw bro..hows the G0 on p965?how far stable it is now?can hit 4ghz dy? |
|
|
Aug 12 2007, 07:52 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(mfcm @ Aug 12 2007, 07:44 PM) thats the answer...haha he got supported finance for the setup hahaa.. act. i know teh reason, just pretend being n0ob btw bro..hows the G0 on p965?how far stable it is now?can hit 4ghz dy? hurmm, i think q66 can hit atleast 3.4Ghz paired with 965p board. im still tryin' to find the setting. btw, here my current test   ps: check at the asus probe's cpu temp. there, quite a large bug eh?? This post has been edited by gengstapo: Aug 12 2007, 07:56 PM |
|
|
Aug 13 2007, 01:28 PM
|
|
Elite
6,139 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Aug 12 2007, 07:52 PM) hahaa.. act. i know teh reason, just pretend being n0ob the cpuz reports voltage 1.088, while asus 1.3hurmm, i think q66 can hit atleast 3.4Ghz paired with 965p board. im still tryin' to find the setting. btw, here my current test ps: check at the asus probe's cpu temp. there, quite a large bug eh?? which is correct? |
|
|
Aug 13 2007, 01:57 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(jinaun @ Aug 13 2007, 01:28 PM) the cpuz reports voltage 1.088, while asus 1.3 the cpu-z totally wrong.. the 1.088v if refer to the BIOS were voltage for SB voltagewhich is correct? i put vcore around 1.35v only, sometimes vdroop to 1.32/ 1.3 in windows |
|
|
Aug 13 2007, 08:56 PM
|
|
Senior Member
1,414 posts Joined: Feb 2006 From: Bandar Tun Razak, KL
|
Guys, I'm going to build SLI system using Q6600 G0 @ 3.6Ghz, so whats board should i buy? Any idea?
|
|
|
Aug 13 2007, 09:02 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(norazwan79 @ Aug 13 2007, 08:56 PM) Guys, I'm going to build SLI system using Q6600 G0 @ 3.6Ghz, so whats board should i buy? Any idea? not quite sure for nvidia based board, well, if ya go thru the disscusion, p35 easily trigger 4Ghz to quaddy |
|
|
Aug 13 2007, 09:22 PM
|
|
Senior Member
1,414 posts Joined: Feb 2006 From: Bandar Tun Razak, KL
|
if p35 support sli, sure i buy.
|
|
|
Aug 13 2007, 09:47 PM
|
|
Senior Member
1,201 posts Joined: Dec 2004 From: Kuala Lumpur
|
QUOTE(norazwan79 @ Aug 13 2007, 09:22 PM) if p35 support sli, sure i buy. If you are going for SLI, nothing can beats EVGA 680i newer revision.. But you might want to wait for intel x38 chipset where its come with dual 16x pci e. Currently, intel havent obtain the license from nvidia for SLI. But its might change in near future |
|
|
Aug 17 2007, 12:07 PM
|
|
Junior Member
38 posts Joined: May 2006
|
dear OC-ers,
i am newbie to the OC scene but would like to learn; i recently purchased the following: Q6600 (2.4GHz) Gigabyte P35-DS3 2GB Kingston Hyper-X 4-4-4-12 MiniTypo 90 Cooler PowerLogic 500W PSU So far i was only able to OC to 2.7GHz (300x9) and the voltage i set it to system (mobo controlled); with this speed, my cpu temp during normal use is about 31/32 degrees. And when running OCCT stress test, it goes up to max of 58degrees; is this acceptable? I tried to OC to 3GHz (333x9) but failed to boot into XP; i get a blue screen. Can anyone tell if i can OC to 3.2GHz with the hardware above for daily use? thanks. This post has been edited by lazzy: Aug 17 2007, 12:09 PM |
|
|
Aug 17 2007, 12:13 PM
|
Senior Member
3,275 posts Joined: Sep 2005
|
QUOTE(lazzy @ Aug 17 2007, 12:07 PM) dear OC-ers, Change ur PSU to something better !!i am newbie to the OC scene but would like to learn; i recently purchased the following: Q6600 (2.4GHz) Gigabyte P35-DS3 2GB Kingston Hyper-X 4-4-4-12 MiniTypo 90 Cooler PowerLogic 500W PSU So far i was only able to OC to 2.7GHz (300x9) and the voltage i set it to system (mobo controlled); with this speed, my cpu temp during normal use is about 31/32 degrees. And when running OCCT stress test, it goes up to max of 58degrees; is this acceptable? I tried to OC to 3GHz (333x9) but failed to boot into XP; i get a blue screen. Can anyone tell if i can OC to 3.2GHz with the hardware above for daily use? thanks. |
|
|
Aug 17 2007, 12:24 PM
|
|
Senior Member
3,239 posts Joined: Jun 2005
|
@lazzy
Q6600 (nice proc, whats the stepping?) Gigabyte P35-DS3 (nice budget board) 2GB Kingston Hyper-X 4-4-4-12 (overpriced ram) MiniTypo 90 Cooler (can't get any better cooler?) PowerLogic 500W PSU (lord, free us from powerlogic and icute..) for your problem, try changing psu. the Q6600 B3 stepping i tested before easily do 3Ghz stress stable without even bumping voltage or even tweak anything beside the clockspeed another problem might be your HSF. really go and get a better one. quadcore is hot. |
|
|
Aug 17 2007, 12:53 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
@lazzy, u needs to change psu and cooler, but since u r newbie, please read oc guide thoroughly.
|
|
|
Aug 17 2007, 07:46 PM
|
|
Junior Member
38 posts Joined: May 2006
|
thanks guys for your feedback.
i actually just bought my HSF; the PSU is from my old P4 3.0GHz HT. what HSF and PSU do you guys recommend to oc to 3.2GHz? |
|
|
Aug 17 2007, 10:51 PM
|
Senior Member
728 posts Joined: Feb 2005 From: Johor
|
QUOTE(lazzy @ Aug 17 2007, 07:46 PM) thanks guys for your feedback. artic cooling freeze 7 pro enough ady lah...... jus RM115.......i actually just bought my HSF; the PSU is from my old P4 3.0GHz HT. what HSF and PSU do you guys recommend to oc to 3.2GHz? if u r "Orang Kaya" thn buy thermalright HR-01 plus/Ultra 120 Extreme,Asus Knight,scythe(forget wht model) this all is expect Air Cooling..... PSU need to c lo.......no CF no SLI 600watt-700watt ok ady,brand like SS,FSP,TT,Toppower,Tagan,Antec,Corsair,and so on..... |
|
|
Aug 17 2007, 11:34 PM
|
|
Junior Member
122 posts Joined: Aug 2007 From: Singapore/Melaka
|
anyway its the rams la. he need to up ram voltage.
|
|
|
Aug 18 2007, 12:42 AM
|
|
Senior Member
2,765 posts Joined: Nov 2005 From: **Hornbills**
|
yeah da psu mite b da prob..else hows the vcore?vdimm?duuno on p35 but if same as others did u diable sum features b4 oc?
|
|
|
Aug 19 2007, 12:57 AM
|
|
Junior Member
238 posts Joined: Jan 2003 From: -warranty void-
|
bros...wats the comfortable temp to run your Q6600 GO daily...
mine 402x9 @1.38(everest read) core 1/2/3/4 idle 44/44/36/36c prime95 2.53 large and small FFT load together 68/68/61/61c mind to share .... |
|
|
Aug 19 2007, 07:16 AM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(hehee:) @ Aug 19 2007, 12:57 AM) bros...wats the comfortable temp to run your Q6600 GO daily... very nice oc bro...3.6 at 1.38v...maybe ur bios setting is 1.4v i guess.mine 402x9 @1.38(everest read) core 1/2/3/4 idle 44/44/36/36c prime95 2.53 large and small FFT load together 68/68/61/61c mind to share .... i couldnt do that with 1.4v better post some screenie to show the temp/setting. Added on August 19, 2007, 7:19 am QUOTE(leslie0880 @ Aug 17 2007, 10:51 PM) artic cooling freeze 7 pro enough ady lah...... jus RM115....... i think the very first thing he shud get for the oc is a decent psu...good HSF will not do if ur voltage supplied to the system is not stable...if u r "Orang Kaya" thn buy thermalright HR-01 plus/Ultra 120 Extreme,Asus Knight,scythe(forget wht model) this all is expect Air Cooling..... PSU need to c lo.......no CF no SLI 600watt-700watt ok ady,brand like SS,FSP,TT,Toppower,Tagan,Antec,Corsair,and so on..... get a good psu and u wont regret it. This post has been edited by remysix: Aug 19 2007, 07:19 AM |
|
|
Aug 19 2007, 09:47 PM
|
|
Senior Member
728 posts Joined: Feb 2005 From: Johor
|
i saw have 1 ppl want to let he FSP 1000watt go on tradezone......
u can go to ask for the best price!! if u dun want 1000watt thn buy my 700watt lah.....i can change to 1000watt haha |
|
|
Aug 20 2007, 02:59 PM
|
|
Senior Member
3,658 posts Joined: Jan 2003
|
QUOTE(lazzy @ Aug 17 2007, 12:07 PM) dear OC-ers, my spec almost same with youi am newbie to the OC scene but would like to learn; i recently purchased the following: Q6600 (2.4GHz) Gigabyte P35-DS3 2GB Kingston Hyper-X 4-4-4-12 MiniTypo 90 Cooler PowerLogic 500W PSU So far i was only able to OC to 2.7GHz (300x9) and the voltage i set it to system (mobo controlled); with this speed, my cpu temp during normal use is about 31/32 degrees. And when running OCCT stress test, it goes up to max of 58degrees; is this acceptable? I tried to OC to 3GHz (333x9) but failed to boot into XP; i get a blue screen. Can anyone tell if i can OC to 3.2GHz with the hardware above for daily use? thanks. only differ psu and cpu cooler i easily 333x9 / 400 x8....... with all dafault setting........ i only facing problem is when i set 400x9 pc able boot up...but when start load windows..blue screen come out...... |
|
|
Aug 20 2007, 03:54 PM
|
|
Senior Member
737 posts Joined: Oct 2005
|
QUOTE(k8118k @ Aug 20 2007, 02:59 PM) my spec almost same with you yeah... power logic is not logic to use to OC the quadcore.. get the better psu..only differ psu and cpu cooler i easily 333x9 / 400 x8....... with all dafault setting........ i only facing problem is when i set 400x9 pc able boot up...but when start load windows..blue screen come out...... plus, i believe you might need to tweak your ram and other voltage tweaks.. u know what i mean... -edit- mini typo 90 cooler.. i also believe you need better cooling to do the job.. OC a quadcore means a LOT of heat -edit again- oh.. that's from lazzy post This post has been edited by baok: Aug 20 2007, 03:57 PM |
|
|
Aug 22 2007, 10:52 AM
|
Junior Member
17 posts Joined: Jul 2007 From: Malaysia
|
How about Corsair HX520W?
Good for OC Q6600? Now i using P5N32-E SLI... Having problem to OC my Q6600.... Going to get another MB soon.... Thinking of what MG should take.... Any recommend? I thinking of XFX N680i or Gigabyte P35-DQ6. Also, what Fan CPU cooling should i use to OC a Q6600? |
|
|
Aug 22 2007, 09:48 PM
|
|
Senior Member
728 posts Joined: Feb 2005 From: Johor
|
QUOTE(sammizai @ Aug 22 2007, 10:52 AM) How about Corsair HX520W? if want change mb,dun get back Nvidia chipsetGood for OC Q6600? Now i using P5N32-E SLI... Having problem to OC my Q6600.... Going to get another MB soon.... Thinking of what MG should take.... Any recommend? I thinking of XFX N680i or Gigabyte P35-DQ6. Also, what Fan CPU cooling should i use to OC a Q6600? if u want ur proc go high FSB,must take P35-DQ6<-- recommand if no take asus P5K deluxe or Blitz Formula! for the CPU cooling,u can cosider Scythe Infinity or Asus 8 heatpipe 1........ this 2 is very performance CPU cooling,if u want cheap a bit,Artic Cooling freeze 7 pro oso not bad.i m using now! |
|
|
Aug 23 2007, 10:50 AM
|
Junior Member
500 posts Joined: Sep 2005 From: Taiping/Perak 
|
QUOTE(sammizai @ Aug 22 2007, 10:52 AM) How about Corsair HX520W? corsair is also 1 off the most stable power supply.dun grad HX520 just go HX620.check the review.killing some brandded 1000w psu.available in my shop.interest pm me.my selling price for brand new corsair hx620 rm560.Good for OC Q6600? Now i using P5N32-E SLI... Having problem to OC my Q6600.... Going to get another MB soon.... Thinking of what MG should take.... Any recommend? I thinking of XFX N680i or Gigabyte P35-DQ6. Also, what Fan CPU cooling should i use to OC a Q6600? |
|
|
Aug 23 2007, 02:55 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
Got my Q6600 last week and now pairing it with Xigmatek S1283 and MX-2 TIM.
Results are good and now gradually burning in my Quad. Anyways im having irregularities of temp between Cores.. Temp of COre 0 and Core 3 seems to be at average 8-10C! I tried to reseat the HSF cooler but same result. [attachmentid=283119] Anyone having similar issues? Im suspecting either Quad IHS or my Xigmatek HSF is concave. This post has been edited by intune: Aug 23 2007, 02:56 PM |
|
|
Aug 23 2007, 03:31 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intune @ Aug 23 2007, 02:55 PM) Got my Q6600 last week and now pairing it with Xigmatek S1283 and MX-2 TIM. it might really concave(IHS)Results are good and now gradually burning in my Quad. Anyways im having irregularities of temp between Cores.. Temp of COre 0 and Core 3 seems to be at average 8-10C! I tried to reseat the HSF cooler but same result. Anyone having similar issues? Im suspecting either Quad IHS or my Xigmatek HSF is concave. lucky me, i didnt face any prob like this.. btw, what program u use to stress all of the cores? This post has been edited by gengstapo: Aug 23 2007, 03:33 PM |
|
|
Aug 23 2007, 05:03 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Aug 23 2007, 03:31 PM) it might really concave(IHS) Prime95,orthos etc.. Im not sure about the concave..will check with razer blade. Anyways..despite the temp irregularities.. really happy wif results..lucky me, i didnt face any prob like this.. btw, what program u use to stress all of the cores? |
|
|
Aug 23 2007, 07:07 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intune @ Aug 23 2007, 05:03 PM) Anyways..despite the temp irregularities.. really happy wif results.. u mean the 330 x9?? |
|
|
Aug 23 2007, 09:22 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Aug 23 2007, 07:07 PM) u mean the 330 x9?? i mean the temp..will definitely try higher FSB when my Quad finish burnin period.. Tried 350X9 today and was stable.. Anyways im only using 965 mobo (Biostar 965PT) im sure i can better results with a P35 board. |
|
|
Aug 24 2007, 08:27 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intune @ Aug 23 2007, 09:22 PM) i mean the temp..will definitely try higher FSB when my Quad finish burnin period.. ic.. well, im also still on 965p, currently only at 356 x9Tried 350X9 today and was stable.. Anyways im only using 965 mobo (Biostar 965PT) im sure i can better results with a P35 board. i believe we can get better result if using 35p board |
|
|
Aug 24 2007, 10:29 AM
|
|
Senior Member
3,239 posts Joined: Jun 2005
|
i try 400*8 on Q6600+P5K dlx paired with stock heatsink. orthos stable lol. no need burn it or whatsoever. P35 really better choice for quadcore
|
|
|
Aug 24 2007, 10:37 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
Managed to get 3.5Ghz (435X9) on my Q6600 average temp 45C . The Xigmatek sl1283 + mx-2 TIM is really a good pair for cooling the Quad!
|
|
|
Aug 24 2007, 03:27 PM
|
|
Senior Member
728 posts Joined: Feb 2005 From: Johor
|
QUOTE(intune @ Aug 24 2007, 10:37 AM) Managed to get 3.5Ghz (435X9) on my Q6600 average temp 45C . The Xigmatek sl1283 + mx-2 TIM is really a good pair for cooling the Quad! fran.....435*9 = around 3.9Ghz wor...... hav u type wrong? and wht mb u r using?? |
|
|
Aug 24 2007, 04:53 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(leslie0880 @ Aug 24 2007, 03:27 PM) fran..... My Bad.. 435*9 = around 3.9Ghz wor...... hav u type wrong? and wht mb u r using?? [attachmentid=283666] 3.6GHz stable! .. Manage to boot to 3.8Ghz but need add more Vcore. Will do somemore testing soon. Bios Vcore: 1.35V (Vdroop 1.344) Mobo: Biostar 965PT Rev1.0 This post has been edited by intune: Aug 24 2007, 04:57 PM |
|
|
Aug 24 2007, 05:15 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
nice, but it aint passed prime95 correct?
btw, any user here using DFI Infinity P35 Blood-Iron?? This post has been edited by gengstapo: Aug 24 2007, 05:17 PM |
|
|
Aug 24 2007, 07:09 PM
|
|
Junior Member
238 posts Joined: Jan 2003 From: -warranty void-
|
just found the sweet OC point of my Q66...
manage to be stable 3.6@1.38 Attached thumbnail(s) 
|
|
|
Aug 24 2007, 11:50 PM
|
|
Senior Member
4,717 posts Joined: Jan 2003
|
wow...are you using water cooling? how come u guys punya temp so good?
QUOTE(intune @ Aug 24 2007, 04:53 PM) My Bad.. [attachmentid=283666] 3.6GHz stable! .. Manage to boot to 3.8Ghz but need add more Vcore. Will do somemore testing soon. Bios Vcore: 1.35V (Vdroop 1.344) Mobo: Biostar 965PT Rev1.0 |
|
|
Aug 25 2007, 12:02 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(kevyeoh @ Aug 24 2007, 11:50 PM) wow...are you using water cooling? how come u guys punya temp so good? No watercooling just plain old Air Heres some reference.. Xigmatek HDT Cooler - http://forum.lowyat.net/index.php?showtopi...50&hl=xigmatek# MX-2 High Performance Thermal Compound - http://forum.lowyat.net/index.php?showtopic=498122&hl=mx-2# Happy Ocing! |
|
|
Aug 27 2007, 09:00 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
I think for those still using 965P just stick with it or buy X38 instead.
|
|
|
Aug 28 2007, 10:38 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Aug 27 2007, 09:00 PM) I think for those still using 965P just stick with it or buy X38 instead. aha.. magaed to get 3.78GHz on my old skool 965PT board.. how high can you get on P35 mobo? |
|
|
Aug 28 2007, 11:25 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
What!!? U get 3.78GHz for quad on 965PT? Thats seem impossible. gengstapo with Comando only get 369x9 ~ 3.3GHz. Anyway i only use E66 with 965P.
|
|
|
Aug 28 2007, 06:23 PM
|
Junior Member
367 posts Joined: Oct 2006
|
halo..every 1...just some suggestion..since this thread is for Q6600..
y not just share some batch num or some OC result on 1 page ke..? and also can compare how the big different btw B3 and G0.. still dont hav very clear picture btw the B3 and G0..but every 1 just looking for G0 only btw..just get 1 L723 today...hehe This post has been edited by jetkiat: Aug 28 2007, 06:24 PM |
|
|
Aug 29 2007, 11:26 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Nice idea but how bout thread starter? Can do between P35 and 965P user list too. Wonder how far can Q6600 oc on 965P though.
|
|
|
Aug 30 2007, 12:13 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Aug 28 2007, 11:25 AM) What!!? U get 3.78GHz for quad on 965PT? Thats seem impossible. gengstapo with Comando only get 369x9 ~ 3.3GHz. Anyway i only use E66 with 965P. yep..3.78GHz pass CPU-Z (still testing)At 3.6GHz Super pi pass! Stable.. (Daily) http://forum.lowyat.net/topic/492598 http://forum.lowyat.net/index.php?act=Atta...=post&id=283575 I did 3.9GHz today but i guess i need to do a pencil mod on my Vdimm cos vdroop very bad..need push more Volts on my rams. Winxp hang after 3secs on boot. [attachmentid=286535] This post has been edited by intune: Aug 30 2007, 12:44 AM |
|
|
Aug 30 2007, 04:42 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Very impressive for using 3.6GHz Q6600 on 965PT for (daily) usage. Haha
|
|
|
Aug 30 2007, 07:45 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Aug 30 2007, 04:42 PM) Very impressive for using 3.6GHz Q6600 on 965PT for (daily) usage. Haha Yeah this ol skool Biostar 965PT rocks! updated Bios today to support 1333MHz..duno if i need that P35 upgrade after all.. Added on August 31, 2007, 12:26 pmIm finding out that irregular temps for my different cores on my G0 Q6600. Is there any one else finding the same issue?. After reseating my HSF on my Q6600 and reapplying MX-2 TIM still have same problem. I think my Processor IHS in bit convex/concave..somehow. I know my Xigmatek S1283 is not the culprit as i have tried it on my HyperTX HSF with same results. Example..2.4GHz@3GHz Core O: 44c Core 1: 35c Core 2: 39c Core 3: 38c Core 0 difference to Core 0 is about average 7C Degrees.. I did some research and this is how the core is layout on the Q6600. 0 1 2 3 But really think that these irregular temp is not critical as i think generally the Q6600 G0's are good new batch of processor from intel looking at the temps im getting at stock and OC. This post has been edited by intune: Aug 31 2007, 12:26 PM |
|
|
Sep 4 2007, 01:13 AM
|
|
Junior Member
238 posts Joined: Jan 2003 From: -warranty void-
|
it will get better after TIM settled...reduce the different
i'm watered with apogeeGT initially result wasn't tat satisfy after TIM settled it become better ... it's quite normal to get those different between cores... even i follow the way to mount Quad still bout the same ... i think the best way to get it equal is to lap the IHS ....warranty void.... |
|
|
Sep 4 2007, 02:11 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(hehee:) @ Sep 4 2007, 01:13 AM) it will get better after TIM settled...reduce the different Yeah really thinking wether wanna lap this IHS..but so far only different of temp bothers me..but im happy with temperature..if B3 then different story.i'm watered with apogeeGT initially result wasn't tat satisfy after TIM settled it become better ... it's quite normal to get those different between cores... even i follow the way to mount Quad still bout the same ... i think the best way to get it equal is to lap the IHS ....warranty void.... |
|
|
Sep 4 2007, 02:33 AM
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(intune @ Sep 4 2007, 02:11 AM) Yeah really thinking wether wanna lap this IHS..but so far only different of temp bothers me..but im happy with temperature..if B3 then different story. advise... be extra careful when laping ur s1283, i have done it but it seem like the heatpipe part got too soft after laping... end up ... the heat pipe part got bended in.... Added on September 4, 2007, 2:36 am QUOTE(intune @ Aug 30 2007, 07:45 PM) Yeah this ol skool Biostar 965PT rocks! updated Bios today to support 1333MHz..duno if i need that P35 upgrade after all.. woot ... i think ur proc have a better batch, mine cant post @ 421*9... hitting wall ald... mine was FPO: L723 can share yours?Added on August 31, 2007, 12:26 pmIm finding out that irregular temps for my different cores on my G0 Q6600. Is there any one else finding the same issue?. After reseating my HSF on my Q6600 and reapplying MX-2 TIM still have same problem. I think my Processor IHS in bit convex/concave..somehow. I know my Xigmatek S1283 is not the culprit as i have tried it on my HyperTX HSF with same results. Example..2.4GHz@3GHz Core O: 44c Core 1: 35c Core 2: 39c Core 3: 38c Core 0 difference to Core 0 is about average 7C Degrees.. I did some research and this is how the core is layout on the Q6600. 0 1 2 3 But really think that these irregular temp is not critical as i think generally the Q6600 G0's are good new batch of processor from intel looking at the temps im getting at stock and OC. This post has been edited by kiong: Sep 4 2007, 02:36 AM |
|
|
Sep 4 2007, 10:57 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(kiong @ Sep 4 2007, 02:33 AM) advise... be extra careful when laping ur s1283, i have done it but it seem like the heatpipe part got too soft after laping... end up ... the heat pipe part got bended in.... Someone advise not to lap the Xigmatek S1283 so i havent done it yet.. prob if i wanna do it just use 2000 grit to get good smooth surface.. Added on September 4, 2007, 2:36 am woot ... i think ur proc have a better batch, mine cant post @ 421*9... hitting wall ald... mine was FPO: L723 can share yours? My Q6600 G0 : L727A672 I dunno wether this good batch or not but i can post upto 450FSB np .. but hang in winxp..most prob my Team Value Rams are holding me back.. prob have different resuts if I have a Good D9's Crucial. |
|
|
Sep 6 2007, 03:46 PM
|
Senior Member
2,378 posts Joined: Jan 2003 From: Miri,Sarawak,Malaysia Status: Dead!
|
Who else use Q6600 on DFI Infinity P965-S Dark? Mind to share some results? I can boot with high clocks setting but just before entering Windows, it will auto restart even if I push more voltage. Tried 0703 and 0725 BIOS, will try 0424 soon.
This post has been edited by Hyde`fK: Sep 6 2007, 03:47 PM |
|
|
Sep 6 2007, 09:41 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
QUOTE(intune @ Sep 4 2007, 10:57 AM) Someone advise not to lap the Xigmatek S1283 so i havent done it yet.. prob if i wanna do it just use 2000 grit to get good smooth surface.. If only my AB9 QUADGT can do like urs there is no need to upgrade new chipset even X48. My Q6600 G0 : L727A672 I dunno wether this good batch or not but i can post upto 450FSB np .. but hang in winxp..most prob my Team Value Rams are holding me back.. prob have different resuts if I have a Good D9's Crucial. |
|
|
Sep 6 2007, 10:40 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Sep 6 2007, 09:41 PM) If only my AB9 QUADGT can do like urs there is no need to upgrade new chipset even X48. Weird technology these days..im starting to think wether upgrading mobo just for the sake of catching with technology is a worthwhile investment anymore. I rather wait for more multithread apps immerge before upgrading any mobo n processor.. Hopefully this Quad can last me atleast a year or so. This post has been edited by intune: Sep 6 2007, 10:41 PM |
|
|
Sep 7 2007, 12:43 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
Has anyone tested using Q6600 G0 with Abit IP35-E?
|
|
|
Sep 7 2007, 05:24 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sHawTY @ Sep 7 2007, 12:43 PM) Has anyone tested using Q6600 G0 with Abit IP35-E? its ur new rig ait?Y doncha do some homework upon em' & later present to us the result?? |
|
|
Sep 7 2007, 08:58 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(gengstapo @ Sep 7 2007, 05:24 PM) its ur new rig ait? Running right now.Y doncha do some homework upon em' & later present to us the result?? The Abit IP35-E manage to OC my Q6600 G0 to 3.2GHz [400X8] @ 1.3Volts [Yeah, this is my favourite speed, and will always use this for 24/7 ].Wanted to push more, but i love my hardwares, plus, this IP35-E is just a temporary motherboard while waiting for X38. Anyway, just want to ask your guys whose been using Q6600 G0. Can the Q6600 G0 run at 400X8 @ Stock Vcore? This post has been edited by sHawTY: Sep 7 2007, 08:58 PM |
|
|
Sep 7 2007, 09:00 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
I believe the result should roughly the same as P35-DS3R or P5K premium
|
|
|
Sep 7 2007, 09:24 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
Now the Q6600 G0 running at 400X8 [3.2Ghz] @ 1.31Volts.
If i set anything lower than that, it can't even pass boot screen. Anyway, does anyone here knows what the stock vcore for this Q6600 G0? |
|
|
Sep 7 2007, 09:35 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Sep 7 2007, 09:24 PM) Now the Q6600 G0 running at 400X8 [3.2Ghz] @ 1.31Volts. Stock vcore for G0 varies..but mostly are at 1.2500V . Some reported higher and there also that reported lower then 1.2500VIf i set anything lower than that, it can't even pass boot screen. Anyway, does anyone here knows what the stock vcore for this Q6600 G0? Taken from VR-Z (thnks graysky)  This post has been edited by intune: Sep 7 2007, 09:40 PM |
|
|
Sep 9 2007, 04:49 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
I thought stock vcore already standardize to 1.35v refer to the box.
|
|
|
Sep 10 2007, 01:39 AM
|
|
Senior Member
728 posts Joined: Feb 2005 From: Johor
|
QUOTE(§layerXT @ Sep 9 2007, 04:49 PM) I thought stock vcore already standardize to 1.35v refer to the box. i think they r recommand max.1.35V on the box...... |
|
|
Sep 10 2007, 01:49 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Oh yeah, my bad. But it always can see default vcore in BIOS isnt it?
|
|
|
Sep 10 2007, 02:04 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
whats the lowest VCore anyone here had their G0 run at stock speed?
|
|
|
Sep 10 2007, 02:15 AM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(intune @ Sep 10 2007, 02:04 AM) whats the lowest VCore anyone here had their G0 run at stock speed? For me, i can only set to 1.25volts.What about your q6600 G0? |
|
|
Sep 10 2007, 10:22 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Sep 10 2007, 02:15 AM) For me, i can only set to 1.25volts. My G0 Q6600 stable at 1.20 - 1.216V stock 2.4ghz speed. Np.What about your q6600 G0? |
|
|
Sep 10 2007, 01:33 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Is it worth to seacrh the minimum vcore for stock operation?
|
|
|
Sep 10 2007, 06:25 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Sep 10 2007, 01:33 PM) Is it worth to seacrh the minimum vcore for stock operation? Seems u like to ask these very subjective questions.. i think you can find the answer yourself. |
|
|
Sep 11 2007, 01:59 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Haha thats right. maybe it might be able to save more electricity.
|
|
|
Sep 13 2007, 01:24 AM
|
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
Q6600 batch L727A672 quick test 3.50GHz [438 x8], prime blend Vcore 1.44v BIOS set... Load at 1.34v, temp 47/45/45/47
Attached thumbnail(s) 
|
|
|
Sep 13 2007, 04:25 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
How long the oc stable on the Prime?
|
|
|
Sep 14 2007, 02:00 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
Did a small test on my Q6600 G0 L7@ 3.2GHz (355X9) at 1.25V . Just wondering wether other G0 could do the same. The test passed Orthos 2hrs and Prime95 stable. Will try lower Vcore soon.
Target: Highest OC at most stable lowest Vcore. At current this Q6600 G0 can do 3.80GHz@1.5V stable on my ol skool Biostar 965PT mobo on Air using Xigmatek S1283 HDT. http://forum.lowyat.net/index.php?act=Atta...=post&id=290507 This post has been edited by intune: Sep 14 2007, 02:11 AM |
|
|
Sep 14 2007, 02:15 AM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Usually they consider 8hours to be able to consider rock stable. And now u still thinking of lower it down at 3.2GHz?
|
|
|
Sep 14 2007, 02:28 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(§layerXT @ Sep 14 2007, 02:15 AM) Usually they consider 8hours to be able to consider rock stable. And now u still thinking of lower it down at 3.2GHz? Will try 8 hours prime at 1.25V @ 3.2GHz today.. Anyways I dont do much Continous OC.. As I do a lot of Video Encoding and Rendering if an OC pass my rigurous rendering jobs and encoding at minimum 1-4 Hrs then I consider it stable IMHO.. priming is good for stability testing but most ppl just use these method for hardcore stability test not real world application tests. So far these G0's are great .. High OC.. stable Vcore and load temps. This post has been edited by intune: Sep 14 2007, 02:37 AM |
|
|
Sep 15 2007, 07:26 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
im wonder to those using 35p chipset if it detect the correct multi for c2x processor when lowered than default. been trying all BIOS for my commando(p965) but none of em' read the correct multi..
This post has been edited by gengstapo: Sep 15 2007, 07:28 PM |
|
|
Sep 19 2007, 05:31 AM
|
Senior Member
871 posts Joined: Jun 2005 From: A Galaxy Far Far Away...
|
just got my Q6600 and i think it's kinda hot. what temps are you guys been getting with stock HSF?
mine is 48-50C |
|
|
Sep 19 2007, 06:24 AM
|
|
Senior Member
737 posts Joined: Oct 2005
|
QUOTE(Ryo @ Sep 19 2007, 05:31 AM) just got my Q6600 and i think it's kinda hot. what temps are you guys been getting with stock HSF? that's normal in stock...mine is 48-50C my q6600@3.0gig@stock vcore idle is 40C with Xigmatek.. 60C at full load... damn hot.. if 3.6gig@1.4825vcore, it reach 72-75C at full load |
|
|
Sep 19 2007, 10:08 AM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(baok @ Sep 19 2007, 06:24 AM) that's normal in stock... Wif Xigma + MX-2 TIM mine is idling at 34-35C stock.. load at 42C.my q6600@3.0gig@stock vcore idle is 40C with Xigmatek.. 60C at full load... damn hot.. if 3.6gig@1.4825vcore, it reach 72-75C at full load |
|
|
Sep 19 2007, 10:54 AM
|
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
3.60GHz, priming at 1.39v with 30°C ambient while CoreTemp read 60°C...
|
|
|
Sep 21 2007, 11:55 PM
|
|
Senior Member
2,042 posts Joined: Jan 2003 From: KL
|
Very nice oc lor, 3.6GHz only 1.39v. Can use 24/7 like that.
|
|
|
Sep 22 2007, 12:18 AM
|
VIP
15,705 posts Joined: Mar 2005 From: Tg. Rambutan
|
QUOTE(§layerXT @ Sep 9 2007, 04:49 PM) I thought stock vcore already standardize to 1.35v refer to the box. If I leave mine at stock. CPUz shows 1.2V oni. |
|
|
Sep 22 2007, 01:41 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
has anyone measure actually how many TDP from Q6600 stock 130W after clocking to 3.2 or 3.6 ghz ??
seems quite good performing.......ithcy to get 1 running on my rig.... This post has been edited by LExus65: Sep 22 2007, 01:41 PM |
|
|
Sep 23 2007, 06:49 PM
|
|
VIP
15,705 posts Joined: Mar 2005 From: Tg. Rambutan
|
Muahahahahahahahahhahaha. My Quad core Q6600 is now running OCCT at 4ghz! I dedicate this 4ghz run to Inter Asia Sdn Bhd n Thermalright, my ever gracious sponsors. Without them this 4ghz run would not be possible. Thank you, thank you, thank you.
Here's the screenshot of the Q6600 running OCCt at 4ghz. Halfway tru OCCT. 
Here's the screenshot of OCCT stable. Finished the run nicely. 
This is my Thermalright cooling set up for the 4ghz run.     This post has been edited by ianho: Sep 23 2007, 06:55 PM |
|
|
Sep 23 2007, 06:54 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(ianho @ Sep 23 2007, 06:49 PM) My Quad core Q6600 is now running OCCT at 4ghz! Uncle!I demand CPUz screenie! Can't believe a 680i chipset based motherboard has the capability of pushing a Q6600 G0 to 506MHz X 8. |
|
|
Sep 24 2007, 02:13 AM
|
Elite
6,799 posts Joined: Jan 2003
|
dude
that is a rocking cpu 500fsb on qd.. gila... shawty it depends on the straps. |
|
|
Sep 24 2007, 03:19 AM
|
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
I think it should be running at 3.60GHz, 450 x8 since the reading on CoreTemp is screwed... CPU-Z screenie would be excellent
|
|
|
Sep 24 2007, 05:54 AM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(cstkl1 @ Sep 24 2007, 02:13 AM) shawty it depends on the straps. What do you mean by that? |
|
|
Sep 24 2007, 10:44 AM
|
|
Elite
6,799 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Sep 24 2007, 05:54 AM) What do you mean by that? i dont think it applies in this caseas pointed out above the clocks is 450x9=3.6 but a lot of ppl dont realise that a lot of times the fsb u get depends on the straps and the ram mhz/timings ( suspect bandwidth stress) being in sync doesnt neccessarily mean u can get the highest fsb. example my mobo fsb 456 is the sweet spot.. with this at 1111 CL4 i can get bandwidth close to 10k if i was to go any higher or even have higher ram speed with tighter timings the bandwidth is less. Hence u need to find the sweetspot for each mobo. and overcock from there. Very evident when u see aquamark scores when bandwidth with low latency timings can account to more than 10fps diifference. This post has been edited by cstkl1: Sep 24 2007, 10:48 AM |
|
|
Sep 24 2007, 11:24 AM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(cstkl1 @ Sep 24 2007, 10:44 AM) i dont think it applies in this case so... how's the way to test it out? test each fsb out?as pointed out above the clocks is 450x9=3.6 but a lot of ppl dont realise that a lot of times the fsb u get depends on the straps and the ram mhz/timings ( suspect bandwidth stress) being in sync doesnt neccessarily mean u can get the highest fsb. example my mobo fsb 456 is the sweet spot.. with this at 1111 CL4 i can get bandwidth close to 10k if i was to go any higher or even have higher ram speed with tighter timings the bandwidth is less. Hence u need to find the sweetspot for each mobo. and overcock from there. Very evident when u see aquamark scores when bandwidth with low latency timings can account to more than 10fps diifference. |
|
|
Sep 24 2007, 11:34 AM
|
|
Senior Member
2,825 posts Joined: Jan 2003 From: Miri
|
kiong... You set 450 x8 in BIOS and launch CoreTemp, check out the Frequency in there
 |
|
|
Sep 24 2007, 11:39 AM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(tAmp0i @ Sep 24 2007, 11:34 AM) kiong... You set 450 x8 in BIOS and launch CoreTemp, check out the Frequency in there 4ghz... i test before.. |
|
|
Sep 24 2007, 11:41 AM
|
Senior Member
557 posts Joined: Jul 2006 From: PhotoJournalist
|
QUOTE(intune @ Sep 10 2007, 02:04 AM) whats the lowest VCore anyone here had their G0 run at stock speed? lowers at 0.8V.. highers 1.5V |
|
|
Sep 24 2007, 12:36 PM
|
|
Senior Member
879 posts Joined: Jan 2003
|
QUOTE(cstkl1 @ Sep 24 2007, 10:44 AM) Hence u need to find the sweetspot for each mobo. and overcock from there.  |
|
|
Sep 24 2007, 02:31 PM
|
|
Elite
6,799 posts Joined: Jan 2003
|
QUOTE(intune @ Sep 24 2007, 12:36 PM) and yes.. overclocking means tweaking go look at the database u will find ppl with higher scores at the same mhz. so many things to consider even the fsb affects gpu overclocking. the rams affects the gpu /fsb and vice versa.. we are all learning better still if u go to www.ripping.org dont look at the high clocks.. look at the middle of the table... |
|
|
Sep 24 2007, 03:19 PM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(cstkl1 @ Sep 24 2007, 02:31 PM) oops.. hmm difficult to type on my aging notebook with the lcd like having stripes of colour... the monitor dieing but still fighting a good fight... at 1st i was thinking like got G spot for m/b... wakakkaa jkjk...and yes.. overclocking means tweaking go look at the database u will find ppl with higher scores at the same mhz. so many things to consider even the fsb affects gpu overclocking. the rams affects the gpu /fsb and vice versa.. we are all learning better still if u go to www.ripping.org dont look at the high clocks.. look at the middle of the table... Added on September 24, 2007, 3:19 pm QUOTE(cstkl1 @ Sep 24 2007, 02:31 PM) oops.. hmm difficult to type on my aging notebook with the lcd like having stripes of colour... the monitor dieing but still fighting a good fight... at 1st i was thinking like got G spot for m/b???... wakakkaa jkjk...and yes.. overclocking means tweaking go look at the database u will find ppl with higher scores at the same mhz. so many things to consider even the fsb affects gpu overclocking. the rams affects the gpu /fsb and vice versa.. we are all learning better still if u go to www.ripping.org dont look at the high clocks.. look at the middle of the table... This post has been edited by kiong: Sep 24 2007, 03:19 PM |
|
|
Dec 12 2007, 02:08 AM
|
Junior Member
67 posts Joined: Jul 2006 From: Malaysia
|
emmm can give me some idea how much cpu voltage i should set to OC my Q6600 to 3.0 ghz
=.= newbies in OC |
|
|
Dec 12 2007, 10:02 AM
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
stock voltage shud b able to get 3.0ghz... i think...
Added on December 12, 2007, 10:03 am QUOTE(ianho @ Sep 23 2007, 06:49 PM) Muahahahahahahahahhahaha. My Quad core Q6600 is now running OCCT at 4ghz! I dedicate this 4ghz run to Inter Asia Sdn Bhd n Thermalright, my ever gracious sponsors. Without them this 4ghz run would not be possible. Thank you, thank you, thank you. Is that a maximus formula?... The IFX-14 heatpipes seems to be touching the other sinks.. I'm getting a mobo that fits my IFX-14... Here's the screenshot of the Q6600 running OCCt at 4ghz. Halfway tru OCCT.
Here's the screenshot of OCCT stable. Finished the run nicely.
This is my Thermalright cooling set up for the 4ghz run. » Click to show Spoiler - click again to hide... « This post has been edited by IcEMoCHa: Dec 12 2007, 10:48 AM |
|
|
Dec 12 2007, 11:30 AM
|
Senior Member
526 posts Joined: Jan 2003
|
hey, my q6600 is currently running at 363x9=3.267Ghz, havent increased the vcore since overclocking it, is this normal?? it runs prime95 alright for a couple of hours.
forgot wat the vcore is, i think when running prime95 it's 1.26 something... going to overclock higher. edit: btw it's G0. This post has been edited by tadasu: Dec 12 2007, 11:31 AM |
|
|
Dec 12 2007, 11:34 AM
|
All Stars
10,530 posts Joined: Nov 2004 From: Petaling Jaya & Mid Valley
|
QUOTE(chinyee @ Dec 12 2007, 02:08 AM) emmm can give me some idea how much cpu voltage i should set to OC my Q6600 to 3.0 ghz just leave it at auto and change fsb to 1333. worked for me.... =.= newbies in OC in fact. i can even boot at 1.30v. havent tried stressing at 1.30v yet though QUOTE(IcEMoCHa @ Dec 12 2007, 10:02 AM) stock voltage shud b able to get 3.0ghz... i think... thats the striker extreme Added on December 12, 2007, 10:03 am Is that a maximus formula?... The IFX-14 heatpipes seems to be touching the other sinks.. I'm getting a mobo that fits my IFX-14... QUOTE(tadasu @ Dec 12 2007, 11:30 AM) hey, my q6600 is currently running at 363x9=3.267Ghz, havent increased the vcore since overclocking it, is this normal?? it runs prime95 alright for a couple of hours. u should try OCCT dude. not sure about prime 95. but even running 2 instances of orthos only loads 2 cores while the other 2 stays idle.forgot wat the vcore is, i think when running prime95 it's 1.26 something... going to overclock higher. edit: btw it's G0. |
|
|
Dec 12 2007, 11:38 AM
|
|
Senior Member
526 posts Joined: Jan 2003
|
hmm shall try OCCT. but im pretty sure prime95 stresses all 4 cores as seen on task manager, coretemp and speedfan.
Added on December 12, 2007, 11:39 amalso, is it ok to leave voltage on auto when overclocking? or manual better? i read somewhere that auto always over-estimate it? hence giving higher temperature?? This post has been edited by tadasu: Dec 12 2007, 11:39 AM |
|
|
Dec 12 2007, 11:57 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
damn, still failed to stable at 3.4Ghz, running orthos & suddenly auto-restart
guess what? it my temp, reach 85c.. |
|
|
Dec 12 2007, 01:06 PM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
striker better or blitz or maximus?
This post has been edited by IcEMoCHa: Dec 12 2007, 01:08 PM |
|
|
Dec 12 2007, 02:47 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
my q6600 go at stock clock using stock hsf ... idle around 48C ... load kow kow using everest around 68-69C .... ambient is the normal usual malaysian indoor without aircond ... hehehehe
now using scythe ninja plus .. only doing 3.0 for everyday use .. 8x375 .. idling around 50C ... load kow kow using everest is 68-69C oso ... will have to get a new cooler soon .. TR ultra120extreme ???? seems like very good reviews for this cooler ... btw ... my airflow in casing is super good liauu ... mobo temp is 40C idling 45 max load kow kow ... gfx idling around 51C ... the sounds of a 70CFM fan on the casing exhaust is the one i need to get rid off ... |
|
|
Dec 12 2007, 03:20 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
^if u went to the Hardcooling section, current best review are Thermaltake BigTyphoon 120
it beats all the other(s) expensive HSF out there |
|
|
Dec 12 2007, 03:21 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
i have TR ultra 120 extreme, currently doing 363x9, idle is 38-42, full load is 48 max
edit: i'll double check when i got home, not sure about idle temperature . but max is correct.This post has been edited by tadasu: Dec 12 2007, 03:23 PM |
|
|
Dec 12 2007, 04:07 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
QUOTE(tadasu @ Dec 12 2007, 03:21 PM) i have TR ultra 120 extreme, currently doing 363x9, idle is 38-42, full load is 48 max what did u use to measure the temp ?? coretemp (software) ???edit: i'll double check when i got home, not sure about idle temperature . but max is correct.if coretemp then i assumed u took the highest core readings rite ??? if u used other than coretemp .. everest for example ... there is a CPU as well as 4 other core individual core temps .. these 4 core temps are about the same as the one in coretemp (software) ... my 68-69C is based on the single CPU reading in everest ... if i used coretemp (software) then the highest core reading is about 63-64C ... Added on December 12, 2007, 4:09 pm QUOTE(gengstapo @ Dec 12 2007, 03:20 PM) ^if u went to the Hardcooling section, current best review are Thermaltake BigTyphoon 120 yaa ... the reviews are pretty good for this cooler too ... thanks for the heads up .. it beats all the other(s) expensive HSF out there This post has been edited by QiW: Dec 12 2007, 04:09 PM |
|
|
Dec 12 2007, 07:47 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
Actually i was using TT Big Typhoon 120, i taught it will be better with Thermalright ultra 120 extreme. Honestly, the different is only mininum, you guys will be surprise. The different is only 3-4c compare with Big Typhoon. Anyway, my big typhoon is up for sale, since i am using Thermalright.
|
|
|
Dec 12 2007, 08:03 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(IcEMoCHa @ Dec 12 2007, 01:06 PM) striker better or blitz or maximus? blitz maximus striker duno |
|
|
Dec 12 2007, 08:12 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
ok, i made a big mistake. prime95 only stresses my cpu to about 50%
i dunno y... was using the "blend" test. i tried OCCT with 363x9 and my pc crashed LOLneed to start all over again |
|
|
Dec 12 2007, 08:28 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(tadasu @ Dec 12 2007, 08:12 PM) ok, i made a big mistake. prime95 only stresses my cpu to about 50% u run orthos aite? sure stress only 50% i dunno y... was using the "blend" test. i tried OCCT with 363x9 and my pc crashed LOLneed to start all over again try find the prime95 for quad, it sure stress ur proc 100% |
|
|
Dec 12 2007, 08:30 PM
|
|
Senior Member
7,338 posts Joined: Jan 2003 From: Cybercity of Cyberjaya
|
hehe now i'm back to aircooling and back to my old trusted geminiII.. i dunno why many dun like this hsf but i totally satisfied with it..
now at 3.56ghz, same vcore as my wc before, (1.45v) and stable occt .. full load temp after 15mins OCCT is around 54c and previously with wc around 49c |
|
|
Dec 12 2007, 08:32 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(irenic @ Dec 12 2007, 08:30 PM) hehe now i'm back to aircooling and back to my old trusted geminiII.. i dunno why many dun like this hsf but i totally satisfied with it.. i have to say that is a good temp...now i having bigger problem with this freaking x38...with 3.6ghz prime or occt load..my NB is getting 68c....HOW THE HELL CAN I COOL THIS thingnow at 3.56ghz, same vcore as my wc before, (1.45v) and stable occt .. full load temp after 15mins OCCT is around 54c and previously with wc around 49c |
|
|
Dec 12 2007, 08:34 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intothefantasy @ Dec 12 2007, 08:32 PM) i have to say that is a good temp...now i having bigger problem with this freaking x38...with 3.6ghz prime or occt load..my NB is getting 68c....HOW THE HELL CAN I COOL THIS thing wahh, its hotu can make i lil cooler by mounting a fan near to the NB |
|
|
Dec 12 2007, 08:57 PM
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 11:57 AM) damn, still failed to stable at 3.4Ghz, running orthos & suddenly auto-restart o.Oguess what? it my temp, reach 85c.. 85C for 3.4ghz? what vcore? mine 3.4ghz at 1.39v idle 38C fulload 64C |
|
|
Dec 12 2007, 08:59 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 12 2007, 08:57 PM) o.O BIOS 1.46V, Windows 1.42V85C for 3.4ghz? what vcore? mine 3.4ghz at 1.39v idle 38C fulload 64C dunno what happen with my quad.. p0or week production maybe dya run prime95 to ensure stability? This post has been edited by gengstapo: Dec 12 2007, 09:06 PM |
|
|
Dec 12 2007, 09:01 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(gengstapo @ Dec 12 2007, 08:34 PM) wahh, its hot no place mount le...my maximus is se version...got that 2 tiub thing kacau...can mount fan...also my TRUE is damn big and covered my nbu can make i lil cooler by mounting a fan near to the NB |
|
|
Dec 12 2007, 09:15 PM
|
Junior Member
360 posts Joined: Jan 2003
|
latest price for Q6600 G0 stepping?
|
|
|
Dec 12 2007, 09:19 PM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
ima try maximus ....
Added on December 12, 2007, 9:19 pm QUOTE(nightc @ Dec 12 2007, 09:15 PM) latest price for Q6600 G0 stepping? around RM 800++This post has been edited by IcEMoCHa: Dec 12 2007, 09:19 PM |
|
|
Dec 12 2007, 09:19 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 08:59 PM) BIOS 1.46V, Windows 1.42V yah, prime for 4 hours no problem.dunno what happen with my quad.. p0or week production maybe dya run prime95 to ensure stability? |
|
|
Dec 12 2007, 09:29 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 12 2007, 09:19 PM) yah, prime for 4 hours no problem. nice ehh.. maybe ur proc better than mine |
|
|
Dec 12 2007, 09:44 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 09:29 PM) nice ehh.. maybe ur proc better than mine yours is G0? |
|
|
Dec 12 2007, 09:50 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 12 2007, 09:44 PM) yours is G0? yepp, kinda crazy to spot the stable setup at 2.4Ghz |
|
|
Dec 12 2007, 10:04 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 09:50 PM) yepp, kinda crazy to spot the stable setup at 2.4Ghz o.O 2.4ghz? typo is it? stock speed is 2.4ghz leh. try up your vtt higher with GTLF(or sth like that, forgot its name liao ) at 67%. |
|
|
Dec 12 2007, 10:35 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 12 2007, 10:04 PM) o.O hahaa.. yeah typo -.-.. should be 3.4Ghz 2.4ghz? typo is it? stock speed is 2.4ghz leh. try up your vtt higher with GTLF(or sth like that, forgot its name liao ) at 67%.btw, ur 1.39V is load period(uguru sensor) or in BIOS? |
|
|
Dec 12 2007, 10:47 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 10:35 PM) hahaa.. yeah typo -.-.. should be 3.4Ghz erm...it's 1.39v in bios.btw, ur 1.39V is load period(uguru sensor) or in BIOS? |
|
|
Dec 12 2007, 10:50 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 12 2007, 10:47 PM) erm...it's 1.39v in bios. confirm ka bro?very less voltage needed eh.. |
|
|
Dec 12 2007, 11:36 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(gengstapo @ Dec 12 2007, 10:50 PM) confirm ka bro? bro...i think prolly la...u need to re-mount ur TTBT...it shouldnt be that hi (85c) with 1.46v...prolly u got contact issue...very less voltage needed eh.. |
|
|
Dec 13 2007, 12:12 AM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 10:50 PM) confirm ka bro? confirmed la. very less voltage needed eh.. now trying 3.6ghz at 1.5v fulload 70C idle 42C |
|
|
Dec 13 2007, 12:28 AM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(sukhoi37 @ Dec 13 2007, 12:12 AM) confirmed la. 3.6 for 1.5v? is kinda high...got any vdroop? now trying 3.6ghz at 1.5v fulload 70C idle 42C |
|
|
Dec 13 2007, 07:59 AM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(intothefantasy @ Dec 13 2007, 12:28 AM) 3.6 for 1.5v? is kinda high...got any vdroop? cpu-z shows 1.4v  |
|
|
Dec 13 2007, 10:19 AM
|
|
Senior Member
526 posts Joined: Jan 2003
|
got a question, my default cpu voltage in bios is 1.3V, while cpu-z shows 1.1 and 1.2 something, so which 1 is accurate?
Added on December 13, 2007, 10:20 amalso, do u guys start with a higher voltage when overclocking, then slowly decrease, or start from minimum? This post has been edited by tadasu: Dec 13 2007, 10:20 AM |
|
|
Dec 13 2007, 11:51 AM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(tadasu @ Dec 13 2007, 10:19 AM) got a question, my default cpu voltage in bios is 1.3V, while cpu-z shows 1.1 and 1.2 something, so which 1 is accurate? #1: both are correct (and in some way, can say incorrect-coz someone will say the correct voltage reading should be taken from DMM). anyway, cpu-z will report (based on ur mobo) voltage at idle and voltage at load. u set in bios=1.3v...cpuz(idle) = 1.2v (vdrop of 0.1v)...cpu(load)=1.1v (vdroop of 0.1v)...Added on December 13, 2007, 10:20 amalso, do u guys start with a higher voltage when overclocking, then slowly decrease, or start from minimum? u always start with lower voltage when OC...i dont think u want to start with 2.0v in ur oc journey |
|
|
Dec 13 2007, 01:38 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
u guys can reach 3.6ghz at 1.39v ........ ur proc is good, mine only get do at 1.55v above but not stable enough for dual orthos.........
now settling at 3.33 but still accpetable for me.......... |
|
|
Dec 13 2007, 05:10 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
Hi, wonder whether you guys increase the fsb voltage when you increase the fsb to more than double the initial setting.
|
|
|
Dec 13 2007, 06:16 PM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
normally you don't need to change the fsb voltage if ur not a extreme OCer...
|
|
|
Dec 13 2007, 06:42 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 12 2007, 08:28 PM) u run orthos aite? sure stress only 50% i was using prime95, only stresses my q6600 about 50%, how come??try find the prime95 for quad, it sure stress ur proc 100% |
|
|
Dec 13 2007, 07:25 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(tadasu @ Dec 13 2007, 06:42 PM) i was using prime95, only stresses my q6600 about 50%, how come?? get the prime95 for quadit would cook ur q6600 |
|
|
Dec 13 2007, 07:45 PM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
my q6600 3.6ghz @ 1.375
Attached thumbnail(s) 
|
|
|
Dec 13 2007, 07:48 PM
|
|
Senior Member
1,311 posts Joined: Jan 2003 From: Puchong/Deep Beach
|
QUOTE(kiong @ Dec 13 2007, 07:45 PM) my q6600 3.6ghz @ 1.375 nice result wif such a nice voltage bro...how long have u run the prime...hopefully it will pass the torture |
|
|
Dec 13 2007, 07:53 PM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(remysix @ Dec 13 2007, 07:48 PM) nice result wif such a nice voltage bro... 3-4 hour ald... nyek nyek nyekhow long have u run the prime...hopefully it will pass the torture |
|
|
Dec 13 2007, 08:39 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(LExus65 @ Dec 13 2007, 01:38 PM) u guys can reach 3.6ghz at 1.39v ........ ur proc is good, mine only get do at 1.55v above but not stable enough for dual orthos......... to get 3.6ghz...i need 1.43 vcore(stable)...and to get 4.0ghz ( suicide) i need 1.6 lol...1.6 in order to use superpi 1m only..the rest all result crash now settling at 3.33 but still accpetable for me.......... |
|
|
Dec 13 2007, 08:53 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
i can only run 3.2 8x400 only at vcore 1.4-1.42 .. tried setting vcore 1.5 9x400 .. system wont even boot up .. hahahahaaa
will try vcore 1.6 later tonite when the mood comes .. anyways ... heres my shot at 3.2 OCCT ... 
forgot to add ... my temp flew up to 70C max and sometimes drop back to 67-68 most of the time .. damm !!! This post has been edited by QiW: Dec 13 2007, 08:54 PM |
|
|
Dec 13 2007, 08:56 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(QiW @ Dec 13 2007, 08:53 PM) i can only run 3.2 8x400 only at vcore 1.4-1.42 .. tried setting vcore 1.5 9x400 .. system wont even boot up .. hahahahaaa hmm strange...with 430x8 i need only 1.38vcore to be stable...and ur temp i am sure is not really ok...kinda weird too lol will try vcore 1.6 later tonite when the mood comes .. anyways ... heres my shot at 3.2 OCCT ...
forgot to add ... my temp flew up to 70C max and sometimes drop back to 67-68 most of the time .. damm !!! |
|
|
Dec 13 2007, 11:01 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intothefantasy @ Dec 13 2007, 08:56 PM) hmm strange...with 430x8 i need only 1.38vcore to be stable...and ur temp i am sure is not really ok...kinda weird too lol err are u comparing 3440Mhz with 3600Mhz there?? dont joking, ok.. |
|
|
Dec 13 2007, 11:40 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(gengstapo @ Dec 13 2007, 11:01 PM) err are u comparing 3440Mhz with 3600Mhz there?? erm 430x8 is 3.6ghz? pls i am not joking bro dont joking, ok.. and i am refering to his temp shoot up This post has been edited by intothefantasy: Dec 13 2007, 11:45 PM |
|
|
Dec 14 2007, 07:29 AM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
yaa .. the temp very strange .. extremely high altho no very high vcore oso ... thats why dare not push any further until i get new cooler ...
i have oso written to intel regarding this temperature prob .. of coz cannot tell them i OC laa .. damm bloody intel .. telling me to test this and that .. change mobo laa .. change casing laa .. my airflow no good la .. etc etc .. just look at my GPU and mobo temp .. very good temps on those 2 item what ... only cpu temp fark up .. so cannot be my airflow prob liau maaa ... have to see how ... save $$$ to get new cooler lorr ... my current ninja previously used on my pentiumD 3.2ghz oso load kow kow forever temp oso never exceeded 61C ... |
|
|
Dec 14 2007, 08:23 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(QiW @ Dec 14 2007, 07:29 AM) yaa .. the temp very strange .. extremely high altho no very high vcore oso ... thats why dare not push any further until i get new cooler ... sometimes the temperature reported by software cant be trust, when priming moment try touch ur HSF & see wheter its really hot or just warm & compared with the temperature reported.. i have oso written to intel regarding this temperature prob .. of coz cannot tell them i OC laa .. damm bloody intel .. telling me to test this and that .. change mobo laa .. change casing laa .. my airflow no good la .. etc etc .. just look at my GPU and mobo temp .. very good temps on those 2 item what ... only cpu temp fark up .. so cannot be my airflow prob liau maaa ... have to see how ... save $$$ to get new cooler lorr ... my current ninja previously used on my pentiumD 3.2ghz oso load kow kow forever temp oso never exceeded 61C ... |
|
|
Dec 14 2007, 11:28 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
try to use ntune with a cpu plug in, the temperature monitor should be quite accurate, or simply core temp. Ninja is still quite capable
most G0 can run 400x8 at stock voltage, ........ but 1.4 @ 3.6 ghz is really good.......... mine bloody one can boot a ta 1.5 @ 3.6ghz 400*9 but cannot do anything ....... push to 1.55 still the same, in the end up give up....... lazy to buy another processor to try again |
|
|
Dec 14 2007, 11:41 AM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
QUOTE(LExus65 @ Dec 14 2007, 11:28 AM) try to use ntune with a cpu plug in, the temperature monitor should be quite accurate, or simply core temp. Ninja is still quite capable i set vcore to 1.6 to try 9x400 last nite ... i read in everest and cpuz vcore reading around 1.55most G0 can run 400x8 at stock voltage, ........ but 1.4 @ 3.6 ghz is really good.......... mine bloody one can boot a ta 1.5 @ 3.6ghz 400*9 but cannot do anything ....... push to 1.55 still the same, in the end up give up....... lazy to buy another processor to try again 3600mhz ... can boot ... idling 55C ... load for 10 secs temp shot over 74C .. straightaway OCCT stopped the test coz i set max temp cut off at 73C .. hahahahaa my ninja not runing the stock scythe fan now ... coz too slow 1100rpm+ only ... i changed to evercool (i think) 120mm fan with speed adjuster one ... running the fan at 2000rpm with 8x400 ... idling 49C load kow kow OCCT test max 70C ... all stable no probs ... i think i will stick with this speed for a while ... |
|
|
Dec 14 2007, 05:00 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(QiW @ Dec 14 2007, 11:41 AM) i set vcore to 1.6 to try 9x400 last nite ... i read in everest and cpuz vcore reading around 1.55 if 3.6ghz u need 1.55vcore it seems to be the problem y ur temp so high tho...u are using p5k deluxe? could u try 1.45-1.48 vcore? how hot is ur northbridge? how much volt u pump for it?3600mhz ... can boot ... idling 55C ... load for 10 secs temp shot over 74C .. straightaway OCCT stopped the test coz i set max temp cut off at 73C .. hahahahaa my ninja not runing the stock scythe fan now ... coz too slow 1100rpm+ only ... i changed to evercool (i think) 120mm fan with speed adjuster one ... running the fan at 2000rpm with 8x400 ... idling 49C load kow kow OCCT test max 70C ... all stable no probs ... i think i will stick with this speed for a while ... |
|
|
Dec 14 2007, 06:10 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
still new to this OC thingy .. so dare not play so much with the other settings .. now just playing around with the bus and multiplier and vcore .. the rest of the stuff i left at auto .. C1E EIST those stuff all disabled of coz .. hehehehe
i did try 1.5vcore to try to get to 3.6 .. wont boot oso .. hahahaaa thats the main prob ... why temp so high ??? i oso keep asking myself that ... maybe i should just sell off the NINJA and get something better ... hmmmmmmmmmmmmm .. need to spend $$$ again stick with this 3.2 for a while ... in the mean time save more $$$ for more cooling power .... |
|
|
Dec 14 2007, 06:39 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
ur temperature is way too high already, ninja should be on par with HR-01.... mine idle temp around 45 (different on each core) load around 55 or some at 3.33ghz. 3.6 reading i could not remember but aound 65 ++
but i mange to keep my eist and thermal management on at 3.33ghz, help reduce the temp quite a lot. Now after changing to 3870, the hot component in my pc turns out to be the processor hehe...... |
|
|
Dec 14 2007, 09:50 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(kiong @ Dec 13 2007, 07:45 PM) my q6600 3.6ghz @ 1.375 really nice, indeeeeed btw, is the 1.375 u set in BIOS or sensor from Asus probe? no vdrop etc? |
|
|
Dec 15 2007, 01:29 AM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(kiong @ Dec 13 2007, 07:45 PM) my q6600 3.6ghz @ 1.375 u have a nice chip there...can i know wats ur cooling? because with 1.44vcore + TRUE i have 60-62c on prime load at 3.6ghz...maybe if i really can stable at 1.375 i am sure i would have a better temp@QiW i am sure u need some voltage for northbridge too...or cpu pll or even fsb vtt stuff...provided u have. |
|
|
Dec 15 2007, 10:34 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
it seems batch 734 got some good 1........
i'm suspecting something, it seems 4 phase power not quite sufficient in OC a quad core, anyone got comment on this ??? Qiw, try to put some volage over the northbridge, helps alot for asus p5k series mobo in OC. |
|
|
Dec 15 2007, 10:49 AM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
Whats the use of tweaking NB and SB voltages?
|
|
|
Dec 15 2007, 11:07 AM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
i belive this links all may help abit since this link refers to asus mobo and u have a p5k mobo
http://www.anandtech.com/cpuchipsets/showdoc.aspx?i=3156&p=4 http://www.anandtech.com/cpuchipsets/showdoc.aspx?i=3156&p=5 http://www.anandtech.com/cpuchipsets/showdoc.aspx?i=3156&p=6 some bios setting explanation, i dun think u need any voltage on sb...for higher fsb i guess nb voltage is sure needed as we are saying quadcore instead of dual core..i personally have 1.41v for northbridge...as my this stupid maximus board always overvolt, i have set 1.37 at bios and turns out to be around 1.41/1.40 This post has been edited by intothefantasy: Dec 15 2007, 11:10 AM |
|
|
Dec 15 2007, 11:40 AM
|
|
Junior Member
103 posts Joined: Mar 2005 From: kuching/miri
|
QUOTE(intothefantasy @ Dec 15 2007, 01:29 AM) u have a nice chip there...can i know wats ur cooling? because with 1.44vcore + TRUE i have 60-62c on prime load at 3.6ghz...maybe if i really can stable at 1.375 i am sure i would have a better temp i'm using xigmatek hdt s1283@QiW i am sure u need some voltage for northbridge too...or cpu pll or even fsb vtt stuff...provided u have. Added on December 15, 2007, 11:45 am QUOTE(gengstapo @ Dec 14 2007, 09:50 PM) really nice, indeeeeed 1.375 in bios, cant remember the vcore after load window... btw, is the 1.375 u set in BIOS or sensor from Asus probe? no vdrop etc? This post has been edited by kiong: Dec 15 2007, 11:45 AM |
|
|
Dec 16 2007, 01:41 AM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(kiong @ Dec 13 2007, 07:53 PM) 3-4 hour ald... nyek nyek nyek Saw your temperature at 66c only, is it the open casing or close casing, i have try with my TTBT at 3.31g at 1.3562v got around 66-70c quad prime, and change to Thermalright ultra 120 extreme with the same setting like TTBT, i got around 61- 67c, wonder how you guys got so low temperature, kind of envy.This post has been edited by Dickong: Dec 16 2007, 01:43 AM |
|
|
Dec 16 2007, 02:38 AM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(Dickong @ Dec 16 2007, 01:41 AM) Saw your temperature at 66c only, is it the open casing or close casing, i have try with my TTBT at 3.31g at 1.3562v got around 66-70c quad prime, and change to Thermalright ultra 120 extreme with the same setting like TTBT, i got around 61- 67c, wonder how you guys got so low temperature, kind of envy. to me that TRUE really need to do some lapping and also TRUE is kinda bad the qc stuff...i prefer the old version of TRUE which have better qc lo...do u notice when u mount ur TRUE after screw liao still can move the heatsink on top the proc? check this thread out http://www.xtremesystems.org/forums/showth...highlight=blitz i use 1sen to replace that white rubber thingy...seems like temp drop abit 2-3c..of course my TRUE is lapped (by acecombat ) |
|
|
Dec 16 2007, 04:08 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
.. at last manage to get stable at 3400Mhz, but its aint a good chips i think
 |
|
|
Dec 17 2007, 01:29 AM
|
Senior Member
520 posts Joined: Mar 2007
|
i've upgraded to q6600 and move from btvx to ifx-14. to my surprise, the temp seems to be hotter after i've fitted ifx. btvx was running idle of approx 42c, 45c, 45c, 39c, where as ifx runs 45, 46c, 45c, 43c. this were the avg temp captured using everest oc to 3.0ghz 1.30vcore.
and during strest test, higest temp recorded was in core0 62C using btvx, and core0 67C using ifx. do u think i need to redo the thermal paste, or just let the paste to break in? This post has been edited by VT-Ten: Dec 17 2007, 01:31 AM |
|
|
Dec 17 2007, 01:36 AM
|
Senior Member
673 posts Joined: Dec 2007
|
VT-Ten: reapply your thermal paste, make sure good airflow
|
|
|
Dec 17 2007, 12:37 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
QUOTE(gengstapo @ Dec 14 2007, 08:23 AM) sometimes the temperature reported by software cant be trust, when priming moment try touch ur HSF & see wheter its really hot or just warm & compared with the temperature reported.. HSF is warm ... still can touch la ... about the same or slightly hotter than last time when i use pentiumD ... pentiumD 3.2 no OC kow kow load forever 61C max ...Added on December 17, 2007, 12:40 pm QUOTE(LExus65 @ Dec 14 2007, 06:39 PM) ur temperature is way too high already, ninja should be on par with HR-01.... mine idle temp around 45 (different on each core) load around 55 or some at 3.33ghz. 3.6 reading i could not remember but aound 65 ++ well ... my temp reading based on everest the single CPU reading ,,, if based on individual temps of core (either everest or coretemp) ... then around 46-47 idling on the highest temp core ... running at 3.2ghz la .. load kow kow 65-66C on highest individual core reading (everest or coretemp) ..but i mange to keep my eist and thermal management on at 3.33ghz, help reduce the temp quite a lot. Now after changing to 3870, the hot component in my pc turns out to be the processor hehe...... This post has been edited by QiW: Dec 17 2007, 12:40 PM |
|
|
Dec 17 2007, 09:19 PM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
QUOTE(VT-Ten @ Dec 17 2007, 01:29 AM) i've upgraded to q6600 and move from btvx to ifx-14. to my surprise, the temp seems to be hotter after i've fitted ifx. btvx was running idle of approx 42c, 45c, 45c, 39c, where as ifx runs 45, 46c, 45c, 43c. this were the avg temp captured using everest oc to 3.0ghz 1.30vcore. Got install fans anot?... At least 2 fans for IFX-14 is recomended...and during strest test, higest temp recorded was in core0 62C using btvx, and core0 67C using ifx. do u think i need to redo the thermal paste, or just let the paste to break in? Added on December 17, 2007, 9:20 pm QUOTE(gengstapo @ Dec 16 2007, 04:08 AM) .. at last manage to get stable at 3400Mhz, but its aint a good chips i think Ur CPU temp very high oh... keep below 50 if possible... This post has been edited by IcEMoCHa: Dec 17 2007, 09:20 PM |
|
|
Dec 18 2007, 01:33 AM
|
|
Junior Member
512 posts Joined: Mar 2007
|
QUOTE(gengstapo @ Dec 16 2007, 04:08 AM) .. at last manage to get stable at 3400Mhz, but its aint a good chips i think use both coretemp and speed fan to monitor ur tempreture. dont bother bout these motherboard based programs. second. the maximum heat for Q6600 G0 Stepping according to Intel is 71C. http://processorfinder.intel.com/Default.aspx so if u go more than 70 u might damage ur cpu. if not, u'll be shortening the life of ur cpu. i want to run my processor for the next 3 years. so im keeping my temp under 60C. (full load 60C) |
|
|
Dec 18 2007, 12:48 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
other than vcore, what other voltages that i need to increase, eg. NB?? by how much and when do i start considering increasing other voltages??
|
|
|
Dec 18 2007, 04:11 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
u dun see significant drop in temperature during idle or IFX 14, it will only show true colour durig loading...... but ur seems a bit high, may be u have to re apply ur thermal paste (too much paste?)
btw gengstapo, what is ur v core.. ur mobo temp probe showing some madness temp wor |
|
|
Dec 18 2007, 04:30 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(night_wolf_in @ Dec 18 2007, 01:33 AM) use both coretemp and speed fan to monitor ur tempreture. dont bother bout these motherboard based programs. ahh, as long no burn mark, we can always RMA itsecond. the maximum heat for Q6600 G0 Stepping according to Intel is 71C. http://processorfinder.intel.com/Default.aspx so if u go more than 70 u might damage ur cpu. if not, u'll be shortening the life of ur cpu. i want to run my processor for the next 3 years. so im keeping my temp under 60C. (full load 60C) no need worry, for next 3 years, there should be better processor than this kentsfield.. QUOTE(LExus65 @ Dec 18 2007, 04:11 PM) btw gengstapo, what is ur v core.. ur mobo temp probe showing some madness temp wor kid.. plss dont do it at home.. hahaa~ jk i put 1.50v for my processor need no worry, none apps can load 100% ur quad except prime/ stress software therefore, my idle temp around >44c & gaming around >60c all time |
|
|
Dec 18 2007, 06:12 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 18 2007, 04:30 PM) ahh, as long no burn mark, we can always RMA it agree.no need worry, for next 3 years, there should be better processor than this kentsfield.. i'll keep my processor the longest ..2 years. |
|
|
Dec 18 2007, 07:13 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
i will keep the processor as long as my favourite game still can run smooth on it........ hehe
1.5v to get it stable..hrm...... should i venture above 1.45v for daily used processor....... hard decision...... hehe btw gengstapo, thx for info.... |
|
|
Dec 18 2007, 07:44 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(LExus65 @ Dec 18 2007, 07:13 PM) i will keep the processor as long as my favourite game still can run smooth on it........ hehe hahaa.. if u say like that, i have no comment to give 1.5v to get it stable..hrm...... should i venture above 1.45v for daily used processor....... hard decision...... hehe btw gengstapo, thx for info.... i believe there will no apps can stress ur cpu more than prime/ stress software do maybe after 10yrs if u can kept it, it still able to serve u well |
|
|
Dec 18 2007, 07:53 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 18 2007, 04:30 PM) need no worry, none apps can load 100% ur quad except prime/ stress software this is what im wondering too. does it really matter to be stable while loading 100% for 8 hours continuously?? since normal softwares stress the processor no where as near as a stress software...therefore, my idle temp around >44c & gaming around >60c all time Added on December 18, 2007, 8:19 pmgot another Q, im using gigabyte x38-ds5, which of the following do i use to increase my ram's voltage? 1. DDR2 overvoltage control 2. DDR reference voltage control 3. DDR termination voltage control This post has been edited by tadasu: Dec 18 2007, 08:19 PM |
|
|
Dec 18 2007, 08:41 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(tadasu @ Dec 18 2007, 07:53 PM) this is what im wondering too. does it really matter to be stable while loading 100% for 8 hours continuously?? since normal softwares stress the processor no where as near as a stress software... no need until 8hrs la brofor sure very hard to passed 8hrs if can pass 2~4hrs enuff ady lorr |
|
|
Dec 18 2007, 09:21 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 18 2007, 08:41 PM) no need until 8hrs la bro oh really?? for sure very hard to passed 8hrs if can pass 2~4hrs enuff ady lorr good good, got hope liao lol |
|
|
Dec 18 2007, 09:32 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
min i think 3 hour enuf..but i personally test for 12 hours lol..for ur gigabyte controling ram volt i think might be this..DDR2 overvoltage control wat is the value for this option in ur bios?
|
|
|
Dec 18 2007, 09:41 PM
|
|
Senior Member
1,988 posts Joined: Aug 2005 From: Puchong, Selangor
|
QUOTE(tadasu @ Dec 18 2007, 07:53 PM) 1. DDR2 overvoltage control 2. DDR reference voltage control 3. DDR termination voltage control |
|
|
Dec 18 2007, 09:42 PM
|
|
Senior Member
526 posts Joined: Jan 2003
|
DDR2 overvoltage control:
Normal +0.05v +0.10v +0.20v etc for my ram, it should be using 2.3v for 1200mhz (default spec), currently running 1.8v at 1066mhz. so i need to add 0.5v, but 0.5v is coloured red (warning), abit scared to increase... but should be fine rite? |
|
|
Dec 18 2007, 10:02 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(tadasu @ Dec 18 2007, 09:42 PM) DDR2 overvoltage control: yea is fine...normally 1066 ram should do at 2.2-2.3v imo..but if ur 1066 speed can do well and stable at 1.8v i dun see any reason to increase it except for abit tweaking at the timingNormal +0.05v +0.10v +0.20v etc for my ram, it should be using 2.3v for 1200mhz (default spec), currently running 1.8v at 1066mhz. so i need to add 0.5v, but 0.5v is coloured red (warning), abit scared to increase... but should be fine rite? This post has been edited by intothefantasy: Dec 18 2007, 10:09 PM |
|
|
Dec 18 2007, 10:36 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
yes im running 2 x vizo 120mm fans.
revert to stock speed. temp avg on 40 43 43 38 idle and 59 56 59 52 load. is this the kind of figures expected from ifx? |
|
|
Dec 19 2007, 12:31 AM
|
Junior Member
372 posts Joined: Dec 2007
|
QUOTE(gengstapo @ Dec 16 2007, 04:08 AM) .. at last manage to get stable at 3400Mhz, but its aint a good chips i think what did u do to get 3.4ghz? i only managed to oc to 2.88ghz.... |
|
|
Dec 19 2007, 11:26 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
dante18, pump voltage that all........ most mobo nowadays does not need much tweaking to get q6600 to 3.2 ghz.......a slight increament can get u there
VT-ten, that temperature is abnormal for stock speed if not mistaken, need some members to confirm that... i remember mine only hovering around 30oC ++ for all 4 cores. so far usually i only test the system for orthos to complete the cycle ( i also dunno how long hehe, but normally i see it runs for 1 hr then ok for me already)... so far in supremecommander it never crash on me, so no problem for me. Previously i was having some bottleneck at 3.0ghz, the game is slide show; but after pumping to 3.33 problem solved...... |
|
|
Dec 19 2007, 11:41 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(intothefantasy @ Dec 18 2007, 09:32 PM) min i think 3 hour enuf..but i personally test for 12 hours lol..for ur gigabyte controling ram volt i think might be this..DDR2 overvoltage control wat is the value for this option in ur bios? err.. 12hrs?, i dont have much fRee time just to stress until 12hrsneed to play game as well, watch some movie & surfing etc but if u got much much fRee time, then its ur call |
|
|
Dec 19 2007, 01:29 PM
|
Senior Member
1,047 posts Joined: Dec 2006 From: GKL/KV
|
QUOTE(gengstapo @ Dec 19 2007, 11:41 AM) err.. 12hrs?, i dont have much fRee time just to stress until 12hrs Ya lor, 12 hours too long. I only did 3 hours top. need to play game as well, watch some movie & surfing etc but if u got much much fRee time, then its ur call |
|
|
Dec 19 2007, 03:17 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(gengstapo @ Dec 19 2007, 11:41 AM) err.. 12hrs?, i dont have much fRee time just to stress until 12hrs sleep time i let it run..wake up go eat breakfast etc and then wait a while all done....btw prime i stil can surf web and movie except for gaming..btw no one is need to follow the way i do...is ur call like u say and yes i have lots of fRee time currentlyneed to play game as well, watch some movie & surfing etc but if u got much much fRee time, then its ur call |
|
|
Dec 19 2007, 10:36 PM
|
|
Junior Member
372 posts Joined: Dec 2007
|
   like this?? so i change the CPU voltage control? Because i tried a few times but pc keep restart....cant even go into windows. But if i choose system voltage control to Auto...then can oc to 2.88ghz only. |
|
|
Dec 19 2007, 11:04 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
what mobo u using listing out the spec are easier for others to guide u....
btw u should set the memory multiplier too, (i dunno how does ur bios work) |
|
|
Dec 20 2007, 01:27 AM
|
|
Junior Member
372 posts Joined: Dec 2007
|
my full spec is here...pls guide me
1) Intel Core 2 Dua Quad6600 2) Gigabyte P35-Ds3 Mainboard 3)Kington Hyper X PC6400 2GB DDR2-800mhz 4) Seagate 320GB SATA 2 5)Galaxy 8800GTS 512 MN DDR3 256bit 6)Cooler master Real power 620watts Modular |
|
|
Dec 20 2007, 07:21 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
^could u edit ur image(s), very large la bro
make em lil small TQ |
|
|
Dec 20 2007, 07:43 AM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
vcore 1.225 ... tak cukup makan leehh .. how to push the proc higher ??
i was told set to auto oso there is a limit the auto vcore will go to .. safety feature i think .. so cannot go any higher liauu the clock .. same thing happened to me .. can try lowering the multiplier to 8x and set CPU host frequency higher on AUTO vcore if u do not wanna play with vcore 1st to clock higher .. |
|
|
Dec 21 2007, 05:45 PM
|
|
Junior Member
372 posts Joined: Dec 2007
|
anyone else can give me some tip to get 3.2ghz on my q6600. my full spec is:
1) Intel Core 2 Dua Quad6600 2) Gigabyte P35-Ds3 Mainboard 3)Kington Hyper X PC6400 2GB DDR2-800mhz 4) Seagate 320GB SATA 2 5)Galaxy 8800GTS 512 MN DDR3 256bit 6)Cooler master Real power 620watts Modula |
|
|
Dec 21 2007, 05:58 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Dante18 @ Dec 21 2007, 05:45 PM) anyone else can give me some tip to get 3.2ghz on my q6600. my full spec is: should be a piece of cake. 1) Intel Core 2 Dua Quad6600 2) Gigabyte P35-Ds3 Mainboard 3)Kington Hyper X PC6400 2GB DDR2-800mhz 4) Seagate 320GB SATA 2 5)Galaxy 8800GTS 512 MN DDR3 256bit 6)Cooler master Real power 620watts Modula i expect you can oc to 3.0ghz with default vcore. |
|
|
Dec 21 2007, 06:28 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(Dante18 @ Dec 21 2007, 05:45 PM) anyone else can give me some tip to get 3.2ghz on my q6600. my full spec is: Duh!It's super easy. Set the bus speed to 400MHz, Multiplier to 8, vcore, set the vcore to 1.31Volts, FSB:Dram ratio put to 1:1, there, you're done. This post has been edited by sHawTY: Dec 21 2007, 06:29 PM |
|
|
Dec 21 2007, 11:00 PM
|
|
Junior Member
372 posts Joined: Dec 2007
|
yeah...manage to stable at 3ghz...and try to get more. Btw thx for the advices.
|
|
|
Dec 22 2007, 12:25 AM
|
Senior Member
2,257 posts Joined: Jan 2003
|
all c2d can break 3ghz
|
|
|
Dec 22 2007, 01:56 AM
|
|
Junior Member
372 posts Joined: Dec 2007
|
got it to 3.4ghz stable now.
|
|
|
Dec 22 2007, 11:35 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(Dante18 @ Dec 22 2007, 01:56 AM) got it to 3.4ghz stable now. cun, have u try stress it?? |
|
|
Dec 22 2007, 01:52 PM
|
|
Junior Member
372 posts Joined: Dec 2007
|
ya..i used OCCT.
|
|
|
Dec 22 2007, 04:32 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Dante18 @ Dec 22 2007, 01:52 PM) ya..i used OCCT. sometimes occt is not accurate to judge the oc is stable.i tried once occt stable for 30 minutes but failed in prime for 10 minutes. |
|
|
Dec 24 2007, 12:52 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sukhoi37 @ Dec 22 2007, 04:32 PM) sometimes occt is not accurate to judge the oc is stable. im havent yet using OCCTi tried once occt stable for 30 minutes but failed in prime for 10 minutes. from what i heard, OCCT only stress cpu while prime/ orthos can stress both cpu & RAM at once(depend on user' input) |
|
|
Dec 24 2007, 10:23 AM
|
|
Senior Member
526 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Dec 24 2007, 12:52 AM) im havent yet using OCCT OCCT can stress both, im using it from what i heard, OCCT only stress cpu while prime/ orthos can stress both cpu & RAM at once(depend on user' input) |
|
|
Dec 26 2007, 01:27 PM
|
|
All Stars
10,530 posts Joined: Nov 2004 From: Petaling Jaya & Mid Valley
|
for those who OC their Q6600 to 3.0Ghz....
wats the LOWEST vcore uve achieved ah?? im trying to lower my vcore as much as possible |
|
|
Dec 26 2007, 05:18 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
1.27v but i'm not sure correct or not since i dunno the exact vcore from my mobo......... it shows 1.28v stock, then i minus -125mv thats it.
but why u want to go as low as possible even with an ifx14 ??? |
|
|
Dec 26 2007, 05:28 PM
|
|
All Stars
10,530 posts Joined: Nov 2004 From: Petaling Jaya & Mid Valley
|
wan to go as cool as possible man....
and save electricity bill oso (as if it makes much of a difference lol) are u getting any kind of vdroop with ur board? |
|
|
Dec 26 2007, 05:35 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(mADmAN @ Dec 26 2007, 01:27 PM) for those who OC their Q6600 to 3.0Ghz.... wats the LOWEST vcore uve achieved ah??  |
|
|
Dec 26 2007, 06:35 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
well bad thing about my DFI, u cannot see how much is the actual voltage being set. vdroop is about 0.003v, but it not proportion so no way of telling. but as a guide, shawty's screen shot is good, stock voltage can get to 3.2 easily
|
|
|
Dec 26 2007, 06:39 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
QUOTE(sHawTY @ Dec 26 2007, 05:35 PM) |
|
|
Dec 26 2007, 06:41 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(intothefantasy @ Dec 26 2007, 06:39 PM) are those under n680i mobo? Nope, it's IP35-E.680i haven't reach. |
|
|
Dec 26 2007, 06:42 PM
|
|
Senior Member
1,561 posts Joined: Feb 2006 From: Penang island
|
nice..hope u can post more quad oc with n680...
|
|
|
Dec 26 2007, 08:30 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Dec 26 2007, 05:35 PM) my ip35-e refuse to change multiplier with higher fsb.... |
|
|
Dec 26 2007, 08:44 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(sukhoi37 @ Dec 26 2007, 08:30 PM) shawty, what you did to change multiplier to 8? Huh?my ip35-e refuse to change multiplier with higher fsb.... Why not? I just change the multiplier in the first page where you change the FSB, the ram to cpu ratio and voltage changing page lor. It's there under the place where you change the FSB. Have u tried updating the bios? This post has been edited by sHawTY: Dec 26 2007, 08:45 PM |
|
|
Dec 26 2007, 08:55 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Dec 26 2007, 08:44 PM) Huh? i'm on v14 bios.Why not? I just change the multiplier in the first page where you change the FSB, the ram to cpu ratio and voltage changing page lor. It's there under the place where you change the FSB. Have u tried updating the bios? already asked a pro ip35-e user in anandtech forum, he ask me go try v12 bios. you try change to higher fsb with somemore vcore. |
|
|
Dec 26 2007, 09:04 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(sukhoi37 @ Dec 26 2007, 08:55 PM) you try change to higher fsb with somemore vcore. Sorry man, i don't want to risk burning either the processor or motherboard since the board is based on 4 phase PWM & the PCB is only based on 4 layers which is a bit too weak for quad core processors.I have something to ask though, you seriously can't change the multiplier even at any FSB? I can change the multiplier at any FSB on any bios. Even on the first bios release i can change the multiplier. Now i'm on v14 bios, and i'm on 400MHz X 8 too. This post has been edited by sHawTY: Dec 26 2007, 09:08 PM |
|
|
Dec 26 2007, 09:18 PM
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
im at 3.6Ghz Q6600 for 24/7 use !!!
|
|
|
Dec 26 2007, 09:19 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Dec 26 2007, 09:04 PM) Sorry man, i don't want to risk burning either the processor or motherboard since the board is based on 4 phase PWM & the PCB is only based on 4 layers which is a bit too weak for quad core processors. weak?I have something to ask though, you seriously can't change the multiplier even at any FSB? I can change the multiplier at any FSB on any bios. Even on the first bios release i can change the multiplier. Now i'm on v14 bios, and i'm on 400MHz X 8 too. there are many users achieve high oc result with this board. weird, maybe i'll try to remove the battery while clear cmos later. how much vcore you need to achieve 3.6ghz? |
|
|
Dec 26 2007, 09:23 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(sukhoi37 @ Dec 26 2007, 09:19 PM) weak? Yes, high achievement, but mostly using Core2Duo, not Core2Quad.there are many users achieve high oc result with this board. weird, maybe i'll try to remove the battery while clear cmos later. how much vcore you need to achieve 3.6ghz? I use 1.32Volts when i'm on 400x9. Didn't test the stability though since i want the processor to only run at highest speed at stock vcore. |
|
|
Dec 26 2007, 09:24 PM
|
Elite
5,434 posts Joined: Dec 2006
|
i did 3.0GHz on 1.2vcore in bios,OCCT in 1.19vcore.
anyway,what's the temp for u guys on 3.0GHz? load and idle temp of using core temp 0.95.4. |
|
|
Dec 26 2007, 09:34 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Dec 26 2007, 09:23 PM) Yes, high achievement, but mostly using Core2Duo, not Core2Quad. your information is urging me to buy new mobo.... I use 1.32Volts when i'm on 400x9. Didn't test the stability though since i want the processor to only run at highest speed at stock vcore. don't poison me |
|
|
Dec 26 2007, 09:41 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(sukhoi37 @ Dec 26 2007, 09:34 PM) your information is urging me to buy new mobo.... Huh? don't poison me Where got? |
|
|
Dec 26 2007, 09:46 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(sHawTY @ Dec 26 2007, 09:04 PM) Sorry man, i don't want to risk burning either the processor or motherboard since the board is based on 4 phase PWM & the PCB is only based on 4 layers which is a bit too weak for quad core processors. |
|
|
Dec 27 2007, 08:08 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(cscheat @ Dec 26 2007, 09:18 PM) im at 3.6Ghz Q6600 for 24/7 use !!! nice man, seems we using the same boardbut mine cant stable at 3.6Ghz maybe overheat problem.. zzZZzz |
|
|
Dec 27 2007, 10:59 AM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(gengstapo @ Dec 27 2007, 08:08 AM) nice man, seems we using the same board Yours is G0 or B3?but mine cant stable at 3.6Ghz maybe overheat problem.. zzZZzz |
|
|
Dec 27 2007, 11:00 AM
|
|
Senior Member
526 posts Joined: Jan 2003
|
QUOTE(cscheat @ Dec 26 2007, 09:18 PM) im at 3.6Ghz Q6600 for 24/7 use !!! nice, what's ur temp at full load??Added on December 27, 2007, 11:33 amand ur vcore? This post has been edited by tadasu: Dec 27 2007, 11:33 AM |
|
|
Dec 27 2007, 03:16 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sHawTY @ Dec 27 2007, 10:59 AM) Yours is G0 or B3? its G0 with 4Ghz stepping been tested by kvmcom, but i bought new unopened cpu~ ability might variable |
|
|
Dec 27 2007, 03:47 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(gengstapo @ Dec 27 2007, 03:16 PM) its G0 with 4Ghz stepping been tested by kvmcom, but i bought new unopened cpu   If it's unopened, how come it's been tested? Isn't that weird. Same batches doesn't mean it can overclock at the same level. |
|
|
Dec 27 2007, 04:13 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(sHawTY @ Dec 27 2007, 03:47 PM) If it's unopened, how come it's been tested? Isn't that weird. Same batches doesn't mean it can overclock at the same level. |
|
|
Dec 27 2007, 08:11 PM
|
Senior Member
2,125 posts Joined: Jan 2003
|
Guys, I'm in the middle of building a new rig. Any suggestion of which mobo should I get to pair with Q6600? Might try OC after got the new rig.
Among this mobo which 1 will u all suggest to get 1. Foxconn MARS P35 2. Gigabyte P35-DS3 3. Asus P5K3 ( is it? saw alot q6600 user using this board ) This post has been edited by nles: Dec 27 2007, 08:13 PM |
|
|
Dec 27 2007, 09:02 PM
|
|
Elite
5,434 posts Joined: Dec 2006
|
QUOTE(nles @ Dec 27 2007, 08:11 PM) Guys, I'm in the middle of building a new rig. Any suggestion of which mobo should I get to pair with Q6600? Might try OC after got the new rig. depend ur budget.Among this mobo which 1 will u all suggest to get 1. Foxconn MARS P35 2. Gigabyte P35-DS3 3. Asus P5K3 ( is it? saw alot q6600 user using this board ) MARS ais almost double the price of DS3 while P5K3 Deluxe using DDR3. |
|
|
Dec 27 2007, 09:19 PM
|
|
Senior Member
2,125 posts Joined: Jan 2003
|
Let's put aside the price 1st.
Will the DS3 outperform MARS? Not planning to upgrade DDR3 anytime soon. So the MARS and Q6600 will work just fine right? Don't want later not OClockable or any compatibility issue because of the board. |
|
|
Dec 27 2007, 09:31 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(nles @ Dec 27 2007, 09:19 PM) Will the DS3 outperform MARS? Don't think so. |
|
|
Dec 29 2007, 06:58 AM
|
|
Senior Member
1,047 posts Joined: Dec 2006 From: GKL/KV
|
QUOTE(nles @ Dec 27 2007, 09:19 PM) Let's put aside the price 1st. Either get MARS or DFI LanParty P35 T2-RS. Both are excellent boards. Will the DS3 outperform MARS? Not planning to upgrade DDR3 anytime soon. So the MARS and Q6600 will work just fine right? Don't want later not OClockable or any compatibility issue because of the board. |
|
|
Dec 29 2007, 06:24 PM
|
|
Senior Member
2,125 posts Joined: Jan 2003
|
QUOTE(skymyxe @ Dec 29 2007, 06:58 AM) Either get MARS or DFI LanParty P35 T2-RS. Both are excellent boards. Getting DFI, prefer the board layout and colour scheme. |
|
|
Dec 29 2007, 09:25 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
Hi guys, i was wondering how u guys can get temperature below 60c when oc Q6600 to 3.6g. In fact i have try changing from my ttbg to tru120x, no matter how, i will get above 60c, example when i oc to 3.3g, voltage set to 1.3625 my core temp will show me around 61-65 full load, n when i set to 3.04g set voltage to 1.232v core temp will show 61c full load. First question, is my mobo sensor going crazy, or something wrong from my settting. For info my room temp around 28-30 without ac, secondly i have resit the heatsink several time still the same. my set at my sign. Forgot, one more thing, even with open casing full load at 3.04g my core temp will show around 53-55c. TQ
This post has been edited by Dickong: Dec 29 2007, 09:44 PM |
|
|
Dec 30 2007, 06:30 AM
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
Just wondering is this ok....can anybody give some comment plz
pic of my primetest add: and why when i installed and tried to use core temp 0.95, my screen went blank and nothing else happens after that. Then i restarted the pc all went ok to normal This post has been edited by ir1z: Dec 30 2007, 06:43 AM |
|
|
Dec 30 2007, 12:36 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
irlz,
how come you've got 2 CPU temp recorded in speedfan? Kinda confused coz 1 is reading 43c and another over 100c. hot hot hot... what hsf are you using? you better check the thermal paste and reseat your hsf. |
|
|
Dec 30 2007, 12:38 PM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
thats the funny thing i dont really know how to use the program anyway. And not sure why there is two cpu readings
add: after installing asus probe2, the temp on that thing doesnot show any irregularities showing a cpu temp of only 34celcius This post has been edited by ir1z: Dec 30 2007, 12:53 PM |
|
|
Dec 30 2007, 12:47 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
QUOTE(ir1z @ Dec 30 2007, 12:38 PM) thats the funny thing i dont really know how to use the program anyway. And not sure why there is two cpu readings try to touch your hsf and see if it feels like 43c or 115c |
|
|
Dec 30 2007, 12:57 PM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
Ive touch it and it feels warm not hot at all and btw im using the thermaltake v1...
Ive done another one and here is what is shown:  add: done some benchmark got this:  This post has been edited by ir1z: Dec 30 2007, 01:55 PM |
|
|
Dec 30 2007, 02:19 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
QUOTE(ir1z @ Dec 30 2007, 12:57 PM) Ive touch it and it feels warm not hot at all and btw im using the thermaltake v1... wow quite a fast pc u got there Ive done another one and here is what is shown: add: done some benchmark got this: noticed that asus probe gives you the wrong readings esp on voltages. i used to have this problem and it's caused by the version used in speedfan and cpu-id. use speedfan v.432 and cpu-id v1.405 or lower and the voltages reading in asus probe will correct itself. |
|
|
Dec 30 2007, 09:45 PM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
Anyway are those temp for the mb, nb and sb normal or is is too hot, coz i havent oced the proc yet and planning to at least oc the proc to 3Ghz minimum
This post has been edited by ir1z: Dec 30 2007, 09:46 PM |
|
|
Dec 30 2007, 10:34 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
temps should be around that figure but the voltages are definitely wrong. oc your quad to 3.0ghz is a piece of cake. but advisable that you sort of the wrong voltage readings in your asus probe first.
|
|
|
Jan 1 2008, 11:32 AM
|
|
Elite
5,434 posts Joined: Dec 2006
|
guys,wanna ask u guys opinion,do u guys believe that a 3.0GHz quad core Q66000 able to OCCT full load at max temp of 52 showing in core temp 0.95.4 by using xigmatek S1283?
anyway,what u guys max temp when load OCCT with 3.0GHz? |
|
|
Jan 1 2008, 12:52 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
OCCT running 30mins stress ... full load temp according to CORETEMP 0954 .. around 64C .. test was ran at nite laa ..
|
|
|
Jan 1 2008, 02:04 PM
|
|
Elite
5,434 posts Joined: Dec 2006
|
OiW,is it the speed in 3.0GHz?
|
|
|
Jan 1 2008, 05:35 PM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(gengstapo @ Dec 27 2007, 10:08 AM) nice man, seems we using the same board wow ! you and me same board and processor !!!but mine cant stable at 3.6Ghz maybe overheat problem.. zzZZzz what is your temp ??? and settings ? QUOTE(tadasu @ Dec 27 2007, 01:00 PM) nice, what's ur temp at full load?? Temp is around 66C at full load !!! Added on December 27, 2007, 11:33 amand ur vcore? QUOTE(Dickong @ Dec 29 2007, 11:25 PM) Hi guys, i was wondering how u guys can get temperature below 60c when oc Q6600 to 3.6g. In fact i have try changing from my ttbg to tru120x, no matter how, i will get above 60c, example when i oc to 3.3g, voltage set to 1.3625 my core temp will show me around 61-65 full load, n when i set to 3.04g set voltage to 1.232v core temp will show 61c full load. First question, is my mobo sensor going crazy, or something wrong from my settting. For info my room temp around 28-30 without ac, secondly i have resit the heatsink several time still the same. my set at my sign. Forgot, one more thing, even with open casing full load at 3.04g my core temp will show around 53-55c. TQ im at 3.6Ghz and temp is 44C idle 66C full load next step i will apply MX-2 to see how is the temp ! |
|
|
Jan 1 2008, 06:40 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(cscheat @ Jan 1 2008, 05:35 PM) wow ! you and me same board and processor !!! what's your vcore?what is your temp ??? and settings ? Temp is around 66C at full load !!! im at 3.6Ghz and temp is 44C idle 66C full load next step i will apply MX-2 to see how is the temp ! mine 3.6ghz 1.514v in bios, idle at 39C, fulload 68C ambiet temp 28C. |
|
|
Jan 1 2008, 08:17 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(cscheat @ Jan 1 2008, 05:35 PM) wow ! you and me same board and processor !!! hahaa.. i think my RAM is holding mewhat is your temp ??? and settings ? im running as my siggy, i cant do anymore higher.. perhaps need change RAM lorr |
|
|
Jan 1 2008, 10:02 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
QUOTE(AceCombat @ Jan 1 2008, 02:04 PM) OiW,is it the speed in 3.0GHz? yaa ... running 8 x 375 .. 3.0ghz .. vcore 1.25cooling scythe ninja plus .. |
|
|
Jan 2 2008, 11:47 PM
|
|
Newbie
3 posts Joined: Dec 2006
|
What ram are you using CSC? im stuck at 3.6 ghz
400x9 temps seem to be alright tho ... its only at 50C in coretemp |
|
|
Jan 3 2008, 08:19 AM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(punkbuster @ Jan 2 2008, 11:47 PM) What ram are you using CSC? im stuck at 3.6 ghz your sig: 3.6ghz at stock vcore? 400x9 temps seem to be alright tho ... its only at 50C in coretemp |
|
|
Jan 3 2008, 10:25 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
3.6ghz at stock vcore is really something there............
so far mine need around 1.54v to reach 3.6ghz...... but temp is way too high around 65oC, so i back it down...... now back to 3.2ghz... i'm suspecting that my board is holding me back, 4 phase power seems to be lacking stability........ anyone have comment on this ? |
|
|
Jan 3 2008, 11:18 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(punkbuster @ Jan 2 2008, 11:47 PM) What ram are you using CSC? im stuck at 3.6 ghz does it really stable?? 400x9 temps seem to be alright tho ... its only at 50C in coretempps: stock vcore doesnt mean 1.35v, depend on the board features when we set option to AUTO This post has been edited by gengstapo: Jan 3 2008, 11:19 AM |
|
|
Jan 3 2008, 11:38 AM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(LExus65 @ Jan 3 2008, 10:25 AM) 3.6ghz at stock vcore is really something there............ 1.54v fulload at 65C? so far mine need around 1.54v to reach 3.6ghz...... but temp is way too high around 65oC, so i back it down...... now back to 3.2ghz... i'm suspecting that my board is holding me back, 4 phase power seems to be lacking stability........ anyone have comment on this ? i think that's awesome for air cooling, mine fulload at 70C with 1.515vcore. what cooler you using? ambient temperature? |
|
|
Jan 3 2008, 02:14 PM
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
OK, guys this is mine 3.4 GHz stable with ambient temp 32C(Malaysia)
Testing:  Stable:  Zalman 9700NT with MX-2 P35-DQ6-Bios ver.F7C This post has been edited by stasio: Jan 3 2008, 04:25 PM |
|
|
Jan 3 2008, 03:17 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
i'm using core temp and rivatuner to monitor temperature, i'm using hr-01 with a vizo fan and a evercool aluminum fan as exhaust (slightly distance away)...... ambient i think around 32 also...... malaysia typical...
|
|
|
Jan 3 2008, 04:27 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
New version of
Core Temp 0.96 is out: here CPU-Z, version 1.42.3: here Prime95 version 25.6 build 6 here EVEREST Ultimate v4.20.1237 Beta here ========================================================================= Gigabyte P35-DQ6,Intel Core2 Quad Q6600@3.6 GHz,2GB DDR2 Kingston HyperX PC6400C4, XFX 8600GT Video Card,2xHitachi SATAII 320GB HDD ========================================================================= This post has been edited by stasio: Jan 3 2008, 04:39 PM |
|
|
Jan 3 2008, 07:24 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(sukhoi37 @ Jan 3 2008, 11:38 AM) 1.54v fulload at 65C? Again i envy u guys getting low temp. when set to high vcore voltage, My question is try to do quad prime and see the real temp when it come to 560000 lucas-lehmer at length 10k, see whether u guy still can get below 65c, if so i really admirer u oc talent.i think that's awesome for air cooling, mine fulload at 70C with 1.515vcore. what cooler you using? ambient temperature? I am now at 3.2g,voltage at 1.325, when 560000 lucas at 10k length my temp reach 68c,68,60,58 but when it prime at 4000 lucas prime at 60c,60,56,55. This post has been edited by Dickong: Jan 3 2008, 07:54 PM |
|
|
Jan 3 2008, 11:37 PM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(sukhoi37 @ Jan 1 2008, 08:40 PM) what's your vcore? My Vcore now is 1.4Vmine 3.6ghz 1.514v in bios, idle at 39C, fulload 68C ambiet temp 28C. QUOTE(punkbuster @ Jan 3 2008, 01:47 AM) What ram are you using CSC? im stuck at 3.6 ghz My ram is Crucial.. look at my sig 400x9 temps seem to be alright tho ... its only at 50C in coretempQUOTE(stasio @ Jan 3 2008, 06:27 PM) New version of wow, thanks for the useful update ! gonna get it now !!!Core Temp 0.96 is out: here CPU-Z, version 1.42.3: here Prime95 version 25.6 build 6 here EVEREST Ultimate v4.20.1237 Beta here Guys, Q6600 is well known for its HOT temp !!  |
|
|
Jan 3 2008, 11:44 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(cscheat @ Jan 3 2008, 11:37 PM) My Vcore now is 1.4V vcore in bios or cpuz?My ram is Crucial.. look at my sig wow, thanks for the useful update ! gonna get it now !!! Guys, Q6600 is well known for its HOT temp !! what's your current clockspeed fulload temperature? |
|
|
Jan 4 2008, 12:04 AM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
my kiLLer temp..
system in idle Attached thumbnail(s) 
|
|
|
Jan 4 2008, 12:11 AM
|
|
Senior Member
520 posts Joined: Mar 2007
|
different apps reported different temps. so which temp reporting application would you believe in?
 |
|
|
Jan 4 2008, 12:35 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
My at 3.5GHZ idle
 On SpeedFan 4.32 add +15C This post has been edited by stasio: Jan 4 2008, 12:37 AM |
|
|
Jan 4 2008, 12:36 AM
|
VIP
8,788 posts Joined: Jan 2003 From: Kuala Lumpur
|
QUOTE(VT-Ten @ Jan 4 2008, 12:11 AM) different apps reported different temps. so which temp reporting application would you believe in? I guess this is a common problem but most people tend to trust Core Temp. |
|
|
Jan 4 2008, 12:42 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
New SpeedFan 4.33(and 4.34beta37)show correct now
|
|
|
Jan 4 2008, 07:21 AM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
i have used speed fan 4.33 and its still not the same shows lower by 7c compared to core temp.
a few question of mine 1. why when i try to oc to 3.2 using any multiplier 8/9 and use occt to stress out occt keep giving me errors (come out graph result saying error detected)after a few minutes? or the pc would just restart itself? (keep in mind im using custom set vcore) 2. tried using stock vcore and still the problem persist. Using prime95 also gave the same result. 3. Things that i change on my mobo asus maximus formula was only the multiplier 8/9, fsb 333/366/400 and vcore to anywhere btw 1.275-1.54 i did not change any other function on the mobo besided those three options plz in need of dire help |
|
|
Jan 4 2008, 07:56 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
My setting for 3.2 stable is 1.33125V in bios,all another are normal.What is your memory?
|
|
|
Jan 4 2008, 08:25 AM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(gengstapo @ Jan 4 2008, 02:04 AM) my kiLLer temp.. HEY !!! your temp is FARKING high in idle !!!!!!!!!!!!!!!!!! system in idle possibilities: 1. Your Vcore too high - try lower your vcore bit by bit 2. Not enough AirFlow in Casing 3. You are not using Good HeatSink 4. Your HeatSink didn't seat properly or contact problem |
|
|
Jan 4 2008, 08:50 AM
|
Junior Member
113 posts Joined: Dec 2006 From: KL
|
» Click to show Spoiler - click again to hide... « Im having the same high temp as u bro..dunno y, but speedfan shows a lower temp than Coretemp. So far running the the rig with the OC setting 24/7 and playing Crysis/NFSPS/The Witcher/FIFA08 wif no prob. Which one should I trust?  |
|
|
Jan 4 2008, 09:34 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
wah it seems some chip really created unequal.......1.4v for 3.6ghz is really good, feel like swapping mine to try my luck..
gengstapo, most proberly ur heat sink is not seat properly, seems to be too high ur temp. Any 60oC should be still save i guess, as the processor recommended operating temp around 71oC. just piece of advise, if ur heat sink have plastic clip or pin better get rid of it before it get melted like my HR-01, change to bolt thru kit improves the temp too. well from a bit of note for my setup, i still enable the c1e and thermal management in bios at 3.2ghz (1.32v) and the prvious 3.3 ghz (1.42v) the voltage is indicative( cant remember, forgot to save screenshot or jolt down); but to go above i need to disable all those. Well there are a few degree drop in the temperature when those are enable. |
|
|
Jan 4 2008, 09:37 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
SpeedFan temperature add +15C
My is same when using version 4.33  This post has been edited by stasio: Jan 4 2008, 09:01 PM |
|
|
Jan 4 2008, 09:47 AM
|
Junior Member
52 posts Joined: Mar 2007
|
How much can we overclocked Core 2 Quad Q6600 2.4GHz with it's standard cooler?
Pc Spec: Processor : Intel Core 2 Quad Q6600 2.4GHz Motherboard : Gigabyte X38-DS5 Memory : Corsair XMS 2 6400 DDR2 (2GB) Graphic Card : Gigabyte 8800GTS 320MB DDR3 320BIT Harddisk : Maxtor 320GB SATA 2 Rom-Drive : Asus 20X DVDRW +/- SATA Casing : Cooler Master CM690 Power Supply : Cooler Master Extreme Power 600W |
|
|
Jan 4 2008, 09:51 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
Speedfan 4.34b37 correct temperature
 This post has been edited by stasio: Jan 4 2008, 09:02 PM |
|
|
Jan 4 2008, 11:02 AM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(stasio @ Jan 4 2008, 11:51 AM) hey ! why not running your RAM at 1000Mhz ? im running 1000Mhz at 4-4-4-12 i dont like 1:1 ratio javascript:emoticon(':o') Added on January 4, 2008, 11:04 amby the way, why using WINDOW XP ??? window xp professional = only support 2 cores window xp home = only support 1 core !!! i'll stick to VISTA This post has been edited by cscheat: Jan 4 2008, 11:04 AM |
|
|
Jan 4 2008, 11:32 AM
|
|
Junior Member
113 posts Joined: Dec 2006 From: KL
|
Just downloaded the 4.34beta 37 but its not detecting my cpu temp or is it? Here's the screenie.
 |
|
|
Jan 4 2008, 01:18 PM
|
|
All Stars
14,909 posts Joined: Jul 2005
|
QUOTE(cscheat @ Jan 4 2008, 11:02 AM) i dont like 1:1 ratio Duh! |
|
|
Jan 4 2008, 01:45 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
cscheat,
my memory is Kingston HyperX KHX6400D2LLK2/2GN,then I prefer to be arround 800.XP using mostly for testing.Also running Vista Ultimate 32&64 bit on same PC.Testing on Vista give me problems. peacezxp, For SpeedFan 4.34beta 37 on Vista "Run as administrator"or set in properties |
|
|
Jan 4 2008, 05:30 PM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
QUOTE(stasio @ Jan 4 2008, 07:56 AM) My setting for 3.2 stable is 1.33125V in bios,all another are normal.What is your memory? im using mushkin 4gb of rams without doing any changes for it in bios... |
|
|
Jan 4 2008, 10:16 PM
|
Elite
4,746 posts Joined: Dec 2007 From: Speed rule
|
QUOTE(malaysian2001uk @ Jan 4 2008, 09:47 AM) How much can we overclocked Core 2 Quad Q6600 2.4GHz with it's standard cooler? +/-3ghz thereabout for G0 stepping.Pc Spec: Processor : Intel Core 2 Quad Q6600 2.4GHz Motherboard : Gigabyte X38-DS5 Memory : Corsair XMS 2 6400 DDR2 (2GB) Graphic Card : Gigabyte 8800GTS 320MB DDR3 320BIT Harddisk : Maxtor 320GB SATA 2 Rom-Drive : Asus 20X DVDRW +/- SATA Casing : Cooler Master CM690 Power Supply : Cooler Master Extreme Power 600W |
|
|
Jan 4 2008, 10:51 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
QUOTE(OC4/3 @ Jan 4 2008, 10:16 PM) +/-3ghz thereabout for G0 stepping. Yeah,arround 3GHz as per Added on January 4, 2008, 10:57 pm QUOTE(ir1z @ Jan 4 2008, 05:30 PM) im using mushkin 4gb of rams without doing any changes for it in bios... Need more detail about your memoryThis post has been edited by stasio: Jan 4 2008, 11:01 PM |
|
|
Jan 5 2008, 12:14 AM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
GUYS !!!
i did a Cooling Mod and my temp drop another 4C !!!! see this at idling !!!!!!!!!  |
|
|
Jan 5 2008, 02:24 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
Me also,adjusting(lowering) some of voltages in bios
Ambient temp 25C,idle  This post has been edited by stasio: Jan 5 2008, 09:53 PM |
|
|
Jan 5 2008, 02:45 AM
|
|
VIP
8,788 posts Joined: Jan 2003 From: Kuala Lumpur
|
Maybe you can share what is the "cooling mod"?
|
|
|
Jan 5 2008, 07:04 PM
|
Senior Member
2,471 posts Joined: Jan 2003
|
QUOTE(cscheat @ Jan 5 2008, 12:14 AM) GUYS !!! nice proc you got there i did a Cooling Mod and my temp drop another 4C !!!! see this at idling !!!!!!!!! |
|
|
Jan 6 2008, 08:37 AM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(stasio @ Jan 5 2008, 04:24 AM) Me also,adjusting(lowering) some of voltages in bios Ambient temp 25C,idle QUOTE(clawhammer @ Jan 5 2008, 04:45 AM) Maybe you can share what is the "cooling mod"? QUOTE(gsan @ Jan 5 2008, 09:04 PM) nice proc you got there will share some of my pics later..1. i lapped my ThermalRight Extreme 2. Add a 14cm fan intake 3. use Push and Pull (2 x 12cm fan) for CPU heat sink 4. use MX-2 Compound 5. lower Vcore |
|
|
Jan 6 2008, 09:32 AM
|
|
Elite
5,434 posts Joined: Dec 2006
|
so u are like this right?
14cm intake go to first 12cm of ur extreme then pull by another 12cm on extreme then exhaust out with 12cm again? |
|
|
Jan 6 2008, 10:54 AM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
Hi guys, do u believe that when i set my vcore to 1.325v oc to 3.2g quad prime stable for more than 8 hours but my temp range from 60-69c, then when i set to 1.275 oc 3.2g orthos plus run aquamark at the same time also stable my temp range from 59-63c, later i play coh for few hours without any problem too, but of course i cant quad prime. My question, whether you guys will set your voltage at 1.325 or 1.275 if its your pc. Since our daily use doesnt use much of quad core what if i say i set the vcore at 1.275v. Any commend of remarks please. TQ
This post has been edited by Dickong: Jan 6 2008, 10:55 AM |
|
|
Jan 6 2008, 01:33 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
|
|
|
Jan 6 2008, 01:56 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(Dickong @ Jan 6 2008, 10:54 AM) Hi guys, do u believe that when i set my vcore to 1.325v oc to 3.2g quad prime stable for more than 8 hours but my temp range from 60-69c, then when i set to 1.275 oc 3.2g orthos plus run aquamark at the same time also stable my temp range from 59-63c, later i play coh for few hours without any problem too, but of course i cant quad prime. My question, whether you guys will set your voltage at 1.325 or 1.275 if its your pc. Since our daily use doesnt use much of quad core what if i say i set the vcore at 1.275v. Any commend of remarks please. TQ 1.325v seems normal leww, Y bother reduce the vcore since u still under recommended voltage??, in fact it doesnt hot while primming.. i set mine 1.50v, would undervolt to 1.46v like that.. |
|
|
Jan 6 2008, 05:20 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
Problem is temp touching 70c when set at 1.325v, moreover,at 1.275v everything seem ok except i cant quad prime. Thats why i need recommendation from our ocer bro.
This post has been edited by Dickong: Jan 6 2008, 05:22 PM |
|
|
Jan 6 2008, 05:25 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(Dickong @ Jan 6 2008, 05:20 PM) Problem is temp touching 70c when set at 1.325v, moreover,at 1.275v everything seem ok except i cant quad prime. Thats why i need recommendation from our ocer bro. 70c did u really touch the HSf?sometimes software provide wrong temp. reading try touch the HSf & wheter its really hot or just warm.. |
|
|
Jan 6 2008, 05:39 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Jan 6 2008, 05:25 PM) 70c did u really touch the HSf? When i touch the heatpipe n the heatsink base, just little warm, but core temp show otherwise, but my ram n nb when touch it really hot.sometimes software provide wrong temp. reading try touch the HSf & wheter its really hot or just warm.. |
|
|
Jan 6 2008, 05:55 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(Dickong @ Jan 6 2008, 05:39 PM) When i touch the heatpipe n the heatsink base, just little warm, but core temp show otherwise, but my ram n nb when touch it really hot. then no big deal what?software cant be trusted always, but it is still good as reference |
|
|
Jan 6 2008, 06:04 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(gengstapo @ Jan 6 2008, 05:55 PM) then no big deal what? Problem is that even everst show the same reading as core temp, can it be my mobo sensor gone kuku, by the way what software u use to detect temp.software cant be trusted always, but it is still good as reference This post has been edited by Dickong: Jan 6 2008, 06:05 PM |
|
|
Jan 6 2008, 06:42 PM
|
|
All Stars
10,688 posts Joined: Jan 2005
|
QUOTE(Dickong @ Jan 6 2008, 06:04 PM) Problem is that even everst show the same reading as core temp, can it be my mobo sensor gone kuku, by the way what software u use to detect temp. u asking me arr? i use only uguru & by touching the HSf when primingmostly the temp showing higher but when i touch the HSf, just warm everest showing the same temp coz it get the temp. value same from the sensor where core temp does.. |
|
|
Jan 7 2008, 10:06 AM
|
|
Senior Member
1,995 posts Joined: May 2005
|
well if 1.275 u can play game without crashes why not? u get lower temperature....
mine is about the same, i can play games and do everything fine, just cannot prime without higher voltage pump........ so i left it a lower for lower temp for daily use, since i dun get crashes or any bsod.... |
|
|
Jan 7 2008, 11:15 AM
|
|
Senior Member
1,262 posts Joined: Aug 2005 From: Mars
|
QUOTE(AceCombat @ Jan 6 2008, 11:32 AM) so u are like this right? 14cm intake go to first 12cm of ur extreme then pull by another 12cm on extreme then exhaust out with 12cm again? i will upload some pics later !!! definately cooler than before !!!!!! my latest temp now at 3.6Ghz !!! IDLE = 34C LOAD = 57C |
|
|
Jan 7 2008, 06:56 PM
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
hey guys, i'm curious, CoreTemp reports my Q6600 G0 temp around 45C at idle @ stock speed, is this normal? ambient temp is 30C.
even at load the temps just increase to about 47C, sorry i'm kinda a noob in this. i want to OC my proc to at least 3.6 soon, so wanna makesure 1st. |
|
|
Jan 7 2008, 07:09 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Xonius @ Jan 7 2008, 06:56 PM) hey guys, i'm curious, CoreTemp reports my Q6600 G0 temp around 45C at idle @ stock speed, is this normal? ambient temp is 30C. you using xigmatek s1283?even at load the temps just increase to about 47C, sorry i'm kinda a noob in this. i want to OC my proc to at least 3.6 soon, so wanna makesure 1st. my idle is 38C, fulload 68C, system temp 33C same cooler with tuniq x2, 1.52 vcore. |
|
|
Jan 7 2008, 07:45 PM
|
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
hmm, after testing with prime my full load goes up to 56C only at stock speed.
and yes, using S1283 with MX-2 |
|
|
Jan 7 2008, 07:51 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(sukhoi37 @ Jan 7 2008, 07:09 PM) you using xigmatek s1283? At 1.52 vcore with full load 68c only really admire you guys, me at 3.2g 1.325 vcore quad prime full load touching 70c. How did you manage that, Is it wcmy idle is 38C, fulload 68C, system temp 33C same cooler with tuniq x2, 1.52 vcore. |
|
|
Jan 7 2008, 07:56 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Dickong @ Jan 7 2008, 07:51 PM) At 1.52 vcore with full load 68c only really admire you guys, me at 3.2g 1.325 vcore quad prime full load touching 70c. How did you manage that, Is it wc i'm using xigmatek s1283 air cooler.try to reinstall your thermalright on the processor, i think sth is wrong there. |
|
|
Jan 7 2008, 08:15 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(sukhoi37 @ Jan 7 2008, 07:56 PM) i'm using xigmatek s1283 air cooler. Is it due to my old school casing. TT xaser lll, in fact i have try several time on the TRU sitting but same .try to reinstall your thermalright on the processor, i think sth is wrong there. |
|
|
Jan 7 2008, 08:23 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Dickong @ Jan 7 2008, 08:15 PM) Is it due to my old school casing. TT xaser lll, in fact i have try several time on the TRU sitting but same . maybe it's due to the uneveness of the TRU's base?open the sidepanel see got any big difference. |
|
|
Jan 7 2008, 11:12 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(sukhoi37 @ Jan 7 2008, 08:23 PM) maybe it's due to the uneveness of the TRU's base? When open side casing the temp drop by around 5-6copen the sidepanel see got any big difference. |
|
|
Jan 7 2008, 11:20 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Dickong @ Jan 7 2008, 11:12 PM) When open side casing the temp drop by around 5-6c maybe something wrong with your sensor.now my system temp: 32C, proc idle: 38C, fulload 67C ambient temp: 27C |
|
|
Jan 7 2008, 11:30 PM
|
|
Senior Member
1,689 posts Joined: Jan 2003
|
QUOTE(sukhoi37 @ Jan 7 2008, 11:20 PM) maybe something wrong with your sensor. I did ask in the earlier forum that it might be my mobo sensor going kuku but no one reply, anyway is it possible the sensor be the culprit. Anyway my idle is alway at around 46, 46, 43 39 now n it is rainingnow my system temp: 32C, proc idle: 38C, fulload 67C ambient temp: 27C |
|
|
Jan 7 2008, 11:32 PM
|
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
hmm i tried to OC my Q6600 to 3.6GHz but i cant get it to be stable for more than 5 minutes stress testing using prime. Raised the vcore till 1.475 (in bios). The full load temp almost 70C.
its stable at 3.2GHz though |
|
|
Jan 7 2008, 11:35 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(Xonius @ Jan 7 2008, 11:32 PM) hmm i tried to OC my Q6600 to 3.6GHz but i cant get it to be stable for more than 5 minutes stress testing using prime. Raised the vcore till 1.475 (in bios). The full load temp almost 70C. try to pump somemore voltage in nb and sb?its stable at 3.2GHz though my q6600 is stable at 1.39vcore in bios 3.4ghz. idle about the same but load around 60C. |
|
|
Jan 7 2008, 11:48 PM
|
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
oh, its my first time OC'ing, so i left the nb and sb voltage at auto.
any hints on how much i should add? |
|
|
Jan 8 2008, 12:22 AM
|
|
Junior Member
41 posts Joined: Aug 2007
|
QUOTE(Dickong @ Jan 7 2008, 11:30 PM) I did ask in the earlier forum that it might be my mobo sensor going kuku but no one reply, anyway is it possible the sensor be the culprit. Anyway my idle is alway at around 46, 46, 43 39 now n it is raining if you have everest ultimate edition, go to tools and click at system stability test. run orthos and burn ur cpu. remove ur cpu fan, check ur cpu throttling graph. the moment cpu throttling graph shoot to 100%, look at the temperature and remember it. this is the temperature you should avoid. |
|
|
Jan 8 2008, 05:31 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
|
|
|
Jan 8 2008, 07:55 PM
|
|
Junior Member
199 posts Joined: Jan 2003 From: Penang
|
Q6600 @ 3.8ghz stock-heatsink
vcore 1.55v Abit IP35-e seems like i got some good luck with this q6600 looking for a good heatsink to buy now what do you guys recommend? im checking out thermalright ultra 120 extreme, but its damn costy RM299 any alternative? im from Penang. the stores here don't have any good stuff xcept for Thermaltake master orb |
|
|
Jan 8 2008, 08:03 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(valent @ Jan 8 2008, 07:55 PM) Q6600 @ 3.8ghz stock-heatsink nice chipvcore 1.55v Abit IP35-e seems like i got some good luck with this q6600 looking for a good heatsink to buy now what do you guys recommend? im checking out thermalright ultra 120 extreme, but its damn costy RM299 any alternative? im from Penang. the stores here don't have any good stuff xcept for Thermaltake master orb what's your temperature for that clock? idle, fulload and system? the thermalright ultra 120 extreme can be bought at around rm250 from moderno. This post has been edited by sukhoi37: Jan 8 2008, 08:04 PM |
|
|
Jan 8 2008, 08:10 PM
|
|
Elite
5,434 posts Joined: Dec 2006
|
QUOTE(valent @ Jan 8 2008, 07:55 PM) Q6600 @ 3.8ghz stock-heatsink pls make sure u have the correct reading or else u will kill ur proc very soon.vcore 1.55v Abit IP35-e seems like i got some good luck with this q6600 looking for a good heatsink to buy now what do you guys recommend? im checking out thermalright ultra 120 extreme, but its damn costy RM299 any alternative? im from Penang. the stores here don't have any good stuff xcept for Thermaltake master orb anyway,TRUE only rm250,RM299 is IFX-14 |
|
|
Jan 8 2008, 08:20 PM
|
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
i got my proc to be stable for Prime95 @ 3.6GHz on 1.48V, in idle its 52C and full load reaches 75C...thats crazy, so i reduced the vcore to 1.45V and its stable for normal use with idle at 48C, no crashes or BSOD yet so far. SuperPI, Everest and 3DMark benchmarking ran smoothly.
will try to lower down the voltage to <1.4V and test for basic system stability soon. ambient temperature is 35C (very hot ) |
|
|
Jan 9 2008, 08:09 AM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
QUOTE(Xonius @ Jan 8 2008, 08:20 PM) i got my proc to be stable for Prime95 @ 3.6GHz on 1.48V, in idle its 52C and full load reaches 75C...thats crazy, so i reduced the vcore to 1.45V and its stable for normal use with idle at 48C, no crashes or BSOD yet so far. SuperPI, Everest and 3DMark benchmarking ran smoothly. did u change the nb and sb volt as well when u did this? as u said before u tried even up to 1.55 but couldnt get it to stable before?will try to lower down the voltage to <1.4V and test for basic system stability soon. ambient temperature is 35C (very hot ) |
|
|
Jan 9 2008, 11:17 AM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
QUOTE(sukhoi37 @ Jan 8 2008, 08:03 PM) nice chip Thanx for info.Where is moderno?what's your temperature for that clock? idle, fulload and system? the thermalright ultra 120 extreme can be bought at around rm250 from moderno. Found-Subang Jaya This post has been edited by stasio: Jan 9 2008, 12:17 PM |
|
|
Jan 9 2008, 11:28 AM
|
Senior Member
1,357 posts Joined: Jan 2003 From: Bukit Jelutong, Shah Alam
|
|
|
|
Jan 9 2008, 12:21 PM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
the moderno shop is located is at subang jaya ss19...
|
|
|
Jan 9 2008, 12:55 PM
|
|
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya
|
Thanx guys
|
|
|
Jan 9 2008, 01:23 PM
|
|
Junior Member
199 posts Joined: Jan 2003 From: Penang
|
idle 63c / load 83c+
yeah, thats why im trying to get a new cooler then this stock hsf lol 83c is crazy hot QUOTE(sukhoi37 @ Jan 8 2008, 08:03 PM) nice chip what's your temperature for that clock? idle, fulload and system? the thermalright ultra 120 extreme can be bought at around rm250 from moderno. |
|
|
Jan 9 2008, 02:48 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(valent @ Jan 9 2008, 01:23 PM) idle 63c / load 83c+ omg... yeah, thats why im trying to get a new cooler then this stock hsf lol 83c is crazy hot i tot the system will auto shutdown when the temperature touched 80C? |
|
|
Jan 9 2008, 04:50 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
you can turn the option off in some motherboard......
but serious it good, u can get it stable at 3.8ghz, but prolong run at 1.55v is rather dangerous |
|
|
Jan 9 2008, 07:09 PM
|
|
Senior Member
1,113 posts Joined: Jan 2005 From: <Insert interesting place>
|
QUOTE(ir1z @ Jan 9 2008, 08:09 AM) did u change the nb and sb volt as well when u did this? as u said before u tried even up to 1.55 but couldnt get it to stable before? ah, i never said i tried up to 1.55, thats someone else, the max i went was 1.48V, it was stable for prime95 at that voltage. anything below is not.and yes i did change the nb/sb volt. my current idle temp is <50C @ 1.45V, but unstable for prime, its stable for normal use, no such crashes or BSOD, gaming, superpi, everest all ran smoothly, no prob. |
|
|
Jan 10 2008, 02:43 AM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
QUOTE(Xonius @ Jan 9 2008, 07:09 PM) ah, i never said i tried up to 1.55, thats someone else, the max i went was 1.48V, it was stable for prime95 at that voltage. anything below is not. hmm same like me lorr like that. Did try push to 3.6 but couldnt get it to run prime or OCCT on a stable basis, but if use just like that everything seems okand yes i did change the nb/sb volt. my current idle temp is <50C @ 1.45V, but unstable for prime, its stable for normal use, no such crashes or BSOD, gaming, superpi, everest all ran smoothly, no prob. |
|
|
Jan 10 2008, 02:47 AM
|
Senior Member
2,402 posts Joined: Dec 2004
|
in average, can q6600 go .. runs at 3.00ghz on stock vcore?
or need to bump vcore that.. |
|
|
Jan 10 2008, 03:04 AM
|
|
All Stars
10,530 posts Joined: Nov 2004 From: Petaling Jaya & Mid Valley
|
confirm can run 3.0 at stock vcore.
my q6600 is running 3.0 at 1.30v.....stock (auto setting) is 1.38. so that means u can even lower down |
|
|
Jan 10 2008, 08:18 AM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
my q6600 can run 3.1ghz at stock vcore.
|
|
|
Jan 10 2008, 11:18 AM
|
|
Elite
5,434 posts Joined: Dec 2006
|
QUOTE(sukhoi37 @ Jan 10 2008, 08:18 AM) my q6600 can run 3.1ghz at stock vcore. bro,ur Q6600 stock vcore is how low? |
|
|
Jan 10 2008, 11:22 AM
|
Senior Member
3,760 posts Joined: Oct 2005
|
Mine runs at 3Ghz at stock vcore too!!!
|
|
|
Jan 10 2008, 12:15 PM
|
|
Senior Member
520 posts Joined: Mar 2007
|
so is mine
3.0ghz at 1.30vcore. |
|
|
Jan 10 2008, 12:27 PM
|
|
Junior Member
354 posts Joined: Sep 2006 From: KL
|
i am running q6600 3.0 at 1.25 vcore (in windows showing 1.25 or lower .. bios i set to 1.275) .. well box says 1.25v is stock anyways ..
This post has been edited by QiW: Jan 10 2008, 12:28 PM |
|
|
Jan 10 2008, 02:45 PM
|
|
Senior Member
4,810 posts Joined: Jan 2003
|
QUOTE(AceCombat @ Jan 10 2008, 11:18 AM) bro,ur Q6600 stock vcore is how low? 1.275v |
|
|
Jan 10 2008, 03:29 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
madman why ur auto setting so high 1 ??
|
|
|
Jan 10 2008, 07:56 PM
|
Senior Member
2,295 posts Joined: Jan 2005 From: Penang
|
hey guys, tried core temp 0.96? although i aint quad core user here, but my m0 e2140 are reporting higher temp, + 15c... compare to b4, 55 to 70c nw omg...
This post has been edited by lichyetan: Jan 10 2008, 07:57 PM |
|
|
Jan 11 2008, 07:42 AM
|
|
Senior Member
1,629 posts Joined: Dec 2007 From: Heaven and Hell
|
QUOTE(lichyetan @ Jan 10 2008, 07:56 PM) hey guys, tried core temp 0.96? although i aint quad core user here, but my m0 e2140 are reporting higher temp, + 15c... compare to b4, 55 to 70c nw omg... what were you using before this? |
|
|
Jan 11 2008, 07:46 AM
|
|
All Stars
10,530 posts Joined: Nov 2004 From: Petaling Jaya & Mid Valley
|
QUOTE(LExus65 @ Jan 10 2008, 03:29 PM) madman why ur auto setting so high 1 ?? its an asus thingy la i gues....when i set to auto pc probe 2 shows 1.38 (or was it 1.36...cant remember)most likely it needs to compensate for the vdroop |
|
|
Jan 11 2008, 12:31 PM
|
|
Senior Member
1,995 posts Joined: May 2005
|
wah asus so siao 1 meh ? but compensating for v drop also no need that much i guess......... but mine is having some serious v drop issue more then 0.03v scary.....
lichyetan, i like to know also ..... the temp so high even u using water cooling... OMG... better check mine with latest version see correct or not..... later on my pc fry.... |
|
|
Jan 11 2008, 04:03 PM
|
Junior Member
384 posts Joined: Mar 2006 From: kl
|
 my pc.. Abit F-I90HD Crucial Ballastix Tracer 1066 2G i got an question.. for number 1. why my cpuz showing 'asynch.' ? for number 2. its need to use this test 'Blend - stress CPU and RAM', and why? nood here.. |
|
|
Jan 13 2008, 11:32 PM
|
|
Senior Member
662 posts Joined: Mar 2006
|
My Vcore is at 1.2375V. I took it off the auto and set it at 1.2375V. But while on load and idling its at 1.18V from Lavalys Everest. OCed it to 333x9 = 3.0Ghz..
Temps around 35-45 on idle and 55-65 on full load. Btw, using the shitty ass Stock Intel HSF... Going to change to Thermalright Ultra 120 Extreme with Silverstone FM123 and MX-2 Artic Cooling thermal paste. My Casing is Antec P182 and my 3 fans are set to Medium setting... Here is the Screenshot of my Q6600 [attachmentid=378754] This post has been edited by bernardryan: Jan 13 2008, 11:46 PM |
| Change to: |  0.2418sec
 0.16
 6 queries
 GZIP Disabled
Time is now: 7th December 2025 - 12:18 AM |
Quote
