Welcome Guest ( Log In | Register )

3 Pages  1 2 3 >Bottom

Outline · [ Standard ] · Linear+

Unifi TMnet Streamyx/Unifi & IPv6, Now live!

views
     
TSwKkaY
post Oct 1 2013, 12:35 AM, updated 9y ago

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
I just heard that TMnet launched IPv6 on September 27th, so I did some experiments tonight and confirm that it is live!

Attached Image Attached Image Attached Image

What I've seen so far from packet dumps:
- PPP IPCP6 negotiates link-local addresses
- SLAAC Router Advertisement gives you a dynamically-assigned /64
- DHCPv6 assigns DNS servers

In addition, asellus reports that DHCPv6-PD is supported. The prefix delegated is dynamic.

DNS servers from DHCPv6:
- 2001:e68::b:68
- 2001:e68:2005:29:202:188:0:133 (does this look familiar? brows.gif )

Attached is a pcap of the IPv6 assignment process.

PDF doc from TMnet about enabling IPv6: http://www.tm.com.my/OnlineHelp/CustomerSu...able%20IPv6.pdf

Known working configurations:
- Asus RT N-12
- Asus RT N-16
- ASUS RT-N56U
- D-Link DSL-2730E
- D-Link DSL-2730U
- D-Link DIR-615
- Linksys E4200 with Tomato RAF by Victek
- Mikrotik
- TMnet "L7"
- TMnet TM6841G
- Windows 7 PPPoE

You can use this site to test your IPv6 connectivity: http://www.test-ipv6.com/

This post has been edited by OKLY: Nov 26 2013, 08:45 PM


Attached File(s)
Attached File  ipv6.pcap.zip ( 922bytes ) Number of downloads: 1041
TSwKkaY
post Oct 1 2013, 01:49 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Can't get the Mikrotik to work with it as it dosen't support SLAAC.

Gonna hook up Linux to this tomorrow and see if TM assigns prefixes over DHCPv6-PD.
paultantk
post Oct 1 2013, 02:21 AM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Any idea how to do this in pfsense?

user posted image

I am guessing don't think just picking SLAAC or DHCP6 there works...

Setting it to SLAC, here's what I get in my logs:

Oct 1 02:24:03 ppp: [wan_link0] LCP: protocol IPV6CP was rejected

This post has been edited by paultantk: Oct 1 2013, 02:26 AM
TSwKkaY
post Oct 1 2013, 02:29 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
No idea... I'm still at very early stages of figuring out their setup. Hopefully someone who knows more can chip in.

The good thing with pfsense though is that being FreeBSD, I'm sure it's possible to hack it to work the same way as the Windows 7 setup.
paultantk
post Oct 1 2013, 08:29 AM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Slaac or dhcp6 doesn't work so far. tried it on my pppoe interface as well as on my vlan500 interface.

my ACNAME is BSRKLJ03, could be this one doesnt have ipv6?

yours?

This post has been edited by paultantk: Oct 1 2013, 09:07 AM
masashi89
post Oct 1 2013, 11:20 AM

殺人の意図..
*****
Senior Member
916 posts

Joined: Feb 2009
From: Merlimau, Melaka Status: Single



hmm sry for being noob, but what good of this IPv6?Thanks in advance~
Alpha_Tay
post Oct 1 2013, 11:41 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
this happen to streamyx too, saw this few days ago.
TSwKkaY
post Oct 1 2013, 11:48 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(paultantk @ Oct 1 2013, 08:29 AM)
Slaac or dhcp6 doesn't work so far. tried it on my pppoe interface as well as on my vlan500 interface.

my ACNAME is BSRKLJ03, could be this one doesnt have ipv6?

yours?
*
I'm on JRC here with a Unifi home account. Just throwing out a thought, are you on Unifi Biz with static IP?
paultantk
post Oct 1 2013, 12:13 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


No... am on VIP 20
Alpha_Tay
post Oct 1 2013, 02:03 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
any router has fully ipv6 support?

it seem router supplied by TM TM6841G Zyxel P-660HW T1 V3 support it.
paultantk
post Oct 1 2013, 02:11 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Is that for streamyx?
Alpha_Tay
post Oct 1 2013, 02:20 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
yea, coz i think it doesnt support pppoe vlan.
Alpha_Tay
post Oct 1 2013, 02:21 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
just tested, this ipv6 doesnt work with streamyx 512kbs or lower package with 10.x lan ip.
aneip
post Oct 1 2013, 02:24 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


Tested slaac on pfsense. Not working, maybe need tweaking. U using direct pppoe on windows?
gin&tonic
post Oct 1 2013, 02:26 PM

Look at all my stars!!
*******
Senior Member
4,874 posts

Joined: Sep 2011


IPv4 & IPv6 whats the difference.? Noob here & hope sifus can pls
explain... Thx
tezro
post Oct 1 2013, 02:43 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


Hi. Any possibility that home user can get static IPv6 from TM?

Thank you. =)
TSwKkaY
post Oct 1 2013, 04:06 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(aneip @ Oct 1 2013, 02:24 PM)
Tested slaac on pfsense. Not working, maybe need tweaking. U using direct pppoe on windows?
*
Yeah, my experiment was on direct pppoe on windows. I stripped out the VLAN 500 tag.
dimenxion
post Oct 1 2013, 06:08 PM

Getting Started
**
Junior Member
289 posts

Joined: Jan 2003
From: Shah Alam



WKkaY

i saw your screenshot on the ipv6 part it doesnt show ipv6 dns server. do u added the ipv6 dns manually after connected or u received it via dhcpv6?
TSwKkaY
post Oct 1 2013, 06:43 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(dimenxion @ Oct 1 2013, 06:08 PM)
i saw your screenshot on the ipv6 part it doesnt show ipv6 dns server. do u added the ipv6 dns manually after connected or u received it via dhcpv6?
*
I think I saw them in wireshark, sent by TM's DHCPv6. I don't know if Windows 7 honors it.
eddie_lim
post Oct 1 2013, 06:47 PM

You Never Walk Alone
Group Icon
Elite
4,024 posts

Joined: Jan 2003
From: In the deepest part of your heart !




QUOTE(wKkaY @ Oct 1 2013, 04:06 PM)
Yeah, my experiment was on direct pppoe on windows. I stripped out the VLAN 500 tag.
*
Can it be done on bridged TM modem before windows pppoe?
or we need a vlan tag remover on windows
Anime4000
post Oct 1 2013, 08:20 PM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


TM provide IPv6, nice...

some question:
before, only having single WAN IP (IPv4) on router side and private IP for LAN.
now with IPv6, every connected PC (LAN) also get unique WAN IPv6?
dimenxion
post Oct 1 2013, 08:39 PM

Getting Started
**
Junior Member
289 posts

Joined: Jan 2003
From: Shah Alam



QUOTE(wKkaY @ Oct 1 2013, 06:43 PM)
I think I saw them in wireshark, sent by TM's DHCPv6. I don't know if Windows 7 honors it.
*
Hmm... Interesting..
It could also be the v4 dns is the one translating it to ipv6 addresses.

I may have to do my own test then smile.gif
aneip
post Oct 1 2013, 09:06 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


Tested on windows 7.. ACNAME "BSRBGI01".

Window 7 using 6TO4 adapter..

Then enable 6TO4 on pfsense. Able to get the IP.. but speedtest show very low speed.. 5Mbps on IPV4, 800Kbps using ipv6.. Tested using http://ipv6-test.com/speedtest/

I think certain place still not support ipv6 natively.


TSwKkaY
post Oct 1 2013, 09:20 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(aneip @ Oct 1 2013, 09:06 PM)
Tested on windows 7..  ACNAME "BSRBGI01".

Window 7 using 6TO4 adapter..

Then enable 6TO4 on pfsense. Able to get the IP.. but speedtest show very low speed.. 5Mbps on IPV4, 800Kbps using ipv6.. Tested using http://ipv6-test.com/speedtest/

I think certain place still not support ipv6 natively.
*
You're doing it wrong if you're using 6to4. It works with practically any ISP that gives you a public IP, and is the stuff of yesterday. TMnet has native IPv6 now which obsoletes the need to use it.
tezro
post Oct 1 2013, 09:34 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


Already testing my Streamyx connection with Windows 7 Broadband dialer.

Looks like my area still not supporting native IPv6 yet. =(
aneip
post Oct 1 2013, 09:47 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


QUOTE(wKkaY @ Oct 1 2013, 09:20 PM)
You're doing it wrong if you're using 6to4. It works with practically any ISP that gives you a public IP, and is the stuff of yesterday. TMnet has native IPv6 now which obsoletes the need to use it.
*
Where is ur location? For windows 7, I just create pppoe connection. After connection established, running ipconfig I can see ipv6 is under 6to4 adapter. Maybe some place still no fully enable. BTW, I'm using VIP 10, in kajang.

paultantk
post Oct 1 2013, 10:42 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Just tried again, getting same error messages. Maybe my area not yet.

CODE
ppp: [wan] IPV6CP: protocol was rejected by peer


This post has been edited by paultantk: Oct 1 2013, 10:42 PM
TSwKkaY
post Oct 2 2013, 12:23 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(paultantk @ Oct 1 2013, 10:42 PM)
Just tried again, getting same error messages. Maybe my area not yet.

CODE
ppp: [wan] IPV6CP: protocol was rejected by peer

*
I guess the BRAS where you and aneip are isn't dual-stack yet.

I'll try it out at my office tomorrow which is hooked up to the KLJ BRAS
TSwKkaY
post Oct 2 2013, 12:34 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Found out a few more things today:

1) They use SLAAC only to assign addresses. DHCPv6 IA and PD are both not used.

2) I've been told that we should be hearing official news "very soon" brows.gif

3) Added a pcap to my first post, here's the text version:
» Click to show Spoiler - click again to hide... «

SUSXploit Machine
post Oct 2 2013, 12:35 AM

❤️ 孤独な旅行者 ❤️​
*******
Senior Member
7,247 posts

Joined: Nov 2008
From: SINGAPORE💃

hmm.gif rclxub.gif

» Click to show Spoiler - click again to hide... «

SUSXploit Machine
post Oct 2 2013, 12:38 AM

❤️ 孤独な旅行者 ❤️​
*******
Senior Member
7,247 posts

Joined: Nov 2008
From: SINGAPORE💃

QUOTE(Alpha_Tay @ Oct 1 2013, 02:21 PM)
just tested, this ipv6 doesnt work with streamyx 512kbs or lower package with 10.x lan ip.
*
according to package or ip?

hw come i get 10.x.x.x IP on 1.5mbps mad.gif last time 115.x.x.x shocking.gif
Alpha_Tay
post Oct 2 2013, 04:04 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(Xploit Machine @ Oct 2 2013, 12:38 AM)
according to package or ip?

hw come i get 10.x.x.x IP on 1.5mbps  mad.gif  last time 115.x.x.x  shocking.gif
*
username package, it isnt 10.x ip, it is 10.x lan ip, while the internet ip is something else.

This post has been edited by Alpha_Tay: Oct 2 2013, 04:36 AM
Alpha_Tay
post Oct 2 2013, 04:11 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(aneip @ Oct 1 2013, 09:06 PM)
Tested on windows 7..  ACNAME "BSRBGI01".

Window 7 using 6TO4 adapter..

Then enable 6TO4 on pfsense. Able to get the IP.. but speedtest show very low speed.. 5Mbps on IPV4, 800Kbps using ipv6.. Tested using http://ipv6-test.com/speedtest/

I think certain place still not support ipv6 natively.
*
geography closer ipv6 supported speedtest server offer better result for real capability testing.
be able to get almost same speed as ipv4 on ipv6 speedtest.

http://www.speedtest.com.sg/speedtest.php

http://www.speedtest.com.sg/speedtest.php?country=HK

http://www.speedtest.com.sg/speedtest.php?country=TW

http://www.speedtest.com.sg/speedtest.php?country=VN

http://www.speedtest.com.my/speedtest.php <currently not supporting ipv6>

http://hk.speedtest6.com/

This post has been edited by Alpha_Tay: Oct 2 2013, 04:59 AM
Alpha_Tay
post Oct 2 2013, 04:25 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
it seem that this native ipv6 (fixed or dynamic) havent reach fixed ip package yet.

This post has been edited by Alpha_Tay: Oct 2 2013, 04:25 AM
Alpha_Tay
post Oct 2 2013, 04:34 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
how to set Prefer IPv4 over IPv6, for vista, 7, 2008. windows default is Prefer IPv6 over IPv4.

http://support.microsoft.com/kb/929852
Alpha_Tay
post Oct 2 2013, 04:40 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(Anime4000 @ Oct 1 2013, 08:20 PM)
TM provide IPv6, nice...

some question:
before, only having single WAN IP (IPv4) on router side and private IP for LAN.
now with IPv6, every connected PC (LAN) also get unique WAN IPv6?
*
have to test the result was yes or no with an ipv6 supported router.
TSwKkaY
post Oct 2 2013, 01:01 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Alpha_Tay Looks like you managed to get it working! (note that your posts will have an "IPv6" tag in the upper right if you post from IPv6)
Alpha_Tay
post Oct 2 2013, 03:57 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(wKkaY @ Oct 2 2013, 01:01 PM)
Alpha_Tay Looks like you managed to get it working! (note that your posts will have an "IPv6" tag in the upper right if you post from IPv6)
*
yea, it is very easy to be done with win7 pppoe software dialer.
paultantk
post Oct 2 2013, 04:08 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Found this announcement

http://unifidr.blogspot.com/2013/09/congra...ipv6-ready.html
asellus
post Oct 2 2013, 06:40 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(paultantk @ Oct 2 2013, 04:08 PM)
Man, so lacking in details as usual. Many of their supplied Steamyx modem doesn't even support IPv6.
TSwKkaY
post Oct 2 2013, 06:45 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 2 2013, 06:40 PM)
Man, so lacking in details as usual. Many of their supplied Steamyx modem doesn't even support IPv6.
*
I understand that's supposed to be an internal announcement. We should be hearing more Soon ™.
Alpha_Tay
post Oct 2 2013, 08:17 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 2 2013, 06:40 PM)
Man, so lacking in details as usual. Many of their supplied Steamyx modem doesn't even support IPv6.
*
it is very normal, and this is happen worldwide, wait for their ipv6 router announcement or somebody DIY their own with a ipv6 supported router.
Eoma
post Oct 2 2013, 11:33 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


WDR4300 IPv6 firmware needs some work. it's half baked.
asellus
post Oct 2 2013, 11:45 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


DHCPv6-PD is supported. wKkaY please fix info in first page.

» Click to show Spoiler - click again to hide... «



tezro
post Oct 3 2013, 12:10 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


Yay....it's confirmed. rclxms.gif

My area also covered. Errr, anyone know what is the settings
in Cisco IOS? hmm.gif
calvin
post Oct 3 2013, 12:16 AM

Tech Enthusiast
******
Senior Member
1,865 posts

Joined: Jan 2003
From: XBOX Live


so basically enabling DHCPv6 client on the WAN interface would do ? unsure.gif

This post has been edited by calvin: Oct 3 2013, 12:18 AM
TSwKkaY
post Oct 3 2013, 12:22 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 2 2013, 11:45 PM)
DHCPv6-PD is supported. wKkaY please fix info in first page.
*
Cool!

I guess there are implementation differences between Unifi and Streamyx as it stands now. When I try to request for PD, TMnet's DHCP server returns a UnspecFail status code.

Looks like you can remove your Hurricane IPv6 tunnel now rclxms.gif
asellus
post Oct 3 2013, 12:22 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


» Click to show Spoiler - click again to hide... «


Speed is good too. No problem there. Nice rclxms.gif rclxms.gif rclxms.gif

This post has been edited by asellus: Oct 3 2013, 12:23 AM
TSwKkaY
post Oct 3 2013, 12:26 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
asellus can you check whether DHCP assigns you a static or dynamic prefix? Try reconnecting PPPoE and see if you get the same prefix.
asellus
post Oct 3 2013, 12:31 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(calvin @ Oct 3 2013, 12:16 AM)
so basically enabling DHCPv6 client on the WAN interface would do ? unsure.gif
*
If you run routerOS, just run a DHCPv6-PD client on your Streamyx PPP interface, and it should pull down a random /64 from the access concentrator. Bind + advertise the automatically-created address pool on the bridge interface, and the computer will automatically get two IPv6 addresses in a default Windows install.

QUOTE(wKkaY @ Oct 3 2013, 12:26 AM)
asellus can you check whether DHCP assigns you a static or dynamic prefix? Try reconnecting PPPoE and see if you get the same prefix.
*
Dynamic prefix. It will change everytime I recycle the PPPoE connection.

This post has been edited by asellus: Oct 3 2013, 07:39 AM
TSwKkaY
post Oct 3 2013, 12:36 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 3 2013, 12:31 AM)
If you run routerOS, just run a DHCPv6-PD client on your Streamyx PPP interface, and it should pull down a random /64 from the access concentrator. Add the /64 to an address pool, then bind + advertise the address pool on the bridge interface, and the computer will automatically get two IPv6 addresses in a default Windows install.
*
Can you check if you can request for something larger than a /64, for exapmle a /63 ?
asellus
post Oct 3 2013, 12:41 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Oct 3 2013, 12:36 AM)
Can you check if you can request for something larger than a /64, for exapmle a /63 ?
*
Already tried requesting a /56, it doesn't seem to be working. routerOS will get a /64, but will only made a random /72 from the supplied /64 available to the IPv6 address pool.

squall0833
post Oct 3 2013, 01:26 AM

Regular
******
Senior Member
1,473 posts

Joined: Oct 2006
From: Jupiter


I don't know much about this..

so what do I need to do to get ipv6 enabled?


currently still not all areas have ipv6 enable right?



im using asus dsl n12u b1 streamyx 4Mbps

This post has been edited by squall0833: Oct 3 2013, 01:31 AM
XeactorZ
post Oct 3 2013, 03:17 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
how to set it ??
using Unifi for home

set at here ??
if yes I follow 1st page and key in, show no internet access @@


Attached thumbnail(s)
Attached Image
tezro
post Oct 3 2013, 08:25 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


Hi,

You can refer this PDF doc from TM:

Guideline to Enable IPv6

This post has been edited by tezro: Oct 3 2013, 08:27 AM
ottomatteseo
post Oct 3 2013, 10:17 AM

New Member
*
Junior Member
46 posts

Joined: May 2008
From: Ipoh, Perak



Hi guys,

just enabled my ipv6 on streamyx using dlink dsl-2730u

Attached Image
TSwKkaY
post Oct 3 2013, 01:53 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(tezro @ Oct 3 2013, 08:25 AM)
Hi,

You can refer this PDF doc from TM:

Guideline to Enable IPv6
*
Thanks, I have updated the first post with this info.
tezro
post Oct 3 2013, 02:44 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(wKkaY @ Oct 3 2013, 01:53 PM)
Thanks, I have updated the first post with this info.
*
You're welcome, Mr wKkaY.
XeactorZ
post Oct 3 2013, 05:50 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(tezro @ Oct 3 2013, 08:25 AM)
Hi,

You can refer this PDF doc from TM:

Guideline to Enable IPv6
*
thanks
I think my model is Model L7 since I have the design
however I can't tick dual LAN, any idea ?

refer the photo


Attached thumbnail(s)
Attached Image
tezro
post Oct 3 2013, 06:35 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(XeactorZ @ Oct 3 2013, 05:50 PM)
thanks
I think my model is Model L7 since I have the design
however I can't tick dual LAN, any idea ?

refer the photo
*
XeactorZ, maybe you can try tick the "Enable IPv6" setting, save the setting and reboot the router.

Then, check back the setting page to see if you can tick the "Dual LAN". smile.gif
calvin
post Oct 4 2013, 12:03 AM

Tech Enthusiast
******
Senior Member
1,865 posts

Joined: Jan 2003
From: XBOX Live


still figuring out how to get things working on pfsense 2.1 ... able to get an external ipv6 IP but traffic is not able to reach the destinations ... unsure.gif
Eoma
post Oct 4 2013, 12:20 AM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(calvin @ Oct 4 2013, 12:03 AM)
still figuring out how to get things working on pfsense 2.1 ... able to get an external ipv6 IP but traffic is not able to reach the destinations ... unsure.gif
*
Are you getting a LAN v6 prefix ?
calvin
post Oct 4 2013, 12:29 AM

Tech Enthusiast
******
Senior Member
1,865 posts

Joined: Jan 2003
From: XBOX Live


QUOTE(Eoma @ Oct 4 2013, 12:20 AM)
Are you getting a LAN v6 prefix ?
*
i'm pinging directly from the router itself .. which has a link local v6 address .. not sure if that was the problem or not,will revisit this again smile.gif
squall0833
post Oct 4 2013, 12:57 AM

Regular
******
Senior Member
1,473 posts

Joined: Oct 2006
From: Jupiter


jeez

Im using Asus DSL n12u b1

doesn't seem have any ipv6 related setting in WAN configuration
paultantk
post Oct 4 2013, 01:05 AM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


QUOTE(calvin @ Oct 4 2013, 12:29 AM)
i'm pinging directly from the router itself .. which has a link local v6 address .. not sure if that was the problem or not,will revisit this again smile.gif
*
I think link local address is not the one that TM assigns

http://en.m.wikipedia.org/wiki/Link-local_address

This post has been edited by paultantk: Oct 4 2013, 01:06 AM
XeactorZ
post Oct 4 2013, 01:49 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(tezro @ Oct 3 2013, 06:35 PM)
XeactorZ, maybe you can try tick the "Enable IPv6" setting, save the setting and reboot the router.

Then, check back the setting page to see if you can tick the "Dual LAN".  smile.gif
*
just try not working
I am using wifi to connect my router on my desktop
is it must connect LAN cable only can tick ?
tezro
post Oct 4 2013, 03:10 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(XeactorZ @ Oct 4 2013, 01:49 AM)
just try not working
I am using wifi to connect my router on my desktop
is it must connect LAN cable only can tick ?
*
I'm also not sure. You can try to do it.

Probably, this is the router firmware limitation. Try upgrading the router firmware, perhaps?

Alpha_Tay
post Oct 4 2013, 03:20 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
http://en.wikipedia.org/wiki/Comparison_of...port_in_routers

http://www.sixxs.net/wiki/Routers

http://www.dlink.com/us/en/technology/dlink-ipv6-solutions

http://www.linksys.com/en-us/ipv6

http://www.tp-link.com.my/article/?faqid=482


XeactorZ
post Oct 4 2013, 03:22 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(tezro @ Oct 4 2013, 03:10 AM)
I'm also not sure. You can try to do it.

Probably, this is the router firmware limitation. Try upgrading the router firmware, perhaps?
*
I am using L7 modem
I saw this 1 to update firmware
https://forum.lowyat.net/topic/2860438

from the link seems require connect LAN cable in order to update
else how ?

This post has been edited by XeactorZ: Oct 4 2013, 03:22 AM
tezro
post Oct 4 2013, 04:14 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(XeactorZ @ Oct 4 2013, 03:22 AM)
I am using L7 modem
I saw this 1 to update firmware
https://forum.lowyat.net/topic/2860438

from the link seems require connect LAN cable in order to update
else how ?
*
XeactorZ, that's the only hint i can show to you. sad.gif

I'm actually not using TM Unifi or using TM supplied modem/router at home, so i have no experience
with the L7 router.

I'm really sorry about this. sweat.gif
Alpha_Tay
post Oct 4 2013, 05:10 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(Alpha_Tay @ Oct 1 2013, 02:21 PM)
just tested, this ipv6 doesnt work with streamyx 512kbs or lower package with 10.x lan ip.
*
ipv6 for streamyx 512kbs or lower package with 10.x lan ip is working now.
XeactorZ
post Oct 4 2013, 03:39 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(tezro @ Oct 4 2013, 04:14 AM)
XeactorZ, that's the only hint i can show to you.  sad.gif

I'm actually not using TM Unifi or using TM supplied modem/router at home, so i have no experience
with the L7 router.

I'm really sorry about this. sweat.gif
*
its okay ...
JohnnyDicaprio
post Oct 4 2013, 07:47 PM

New Member
*
Junior Member
21 posts

Joined: Sep 2011
below are my config for l7 router
i can get ipv6 address for my windows 7 but not for my debian, dont know why.. rclxub.gif rclxub.gif
i have to put image in spoiler, lazy to resize

» Click to show Spoiler - click again to hide... «


results
» Click to show Spoiler - click again to hide... «


thumbup.gif thumbup.gif
TSwKkaY
post Oct 4 2013, 10:07 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(JohnnyDicaprio @ Oct 4 2013, 07:47 PM)
below are my config for l7 router
i can get ipv6 address for my windows 7 but not for my debian, dont know why.. rclxub.gif  rclxub.gif
i have to put image in spoiler, lazy to resize
*
2 scenarios I can think of:

1) router only supports dhcpv6, doesn't support slaac. solution: install dhcpv6 client in your debian box, eg wide-dhcpv6-client or dibbler.

2) router does support SLAAC, but it is disabled in your debian kernel /proc/sys/net settings
powerwoot
post Oct 4 2013, 10:10 PM

讨厌的 ubuntu
*******
Senior Member
2,930 posts

Joined: Jan 2007
From: Kolej Universiti Agrosains Malaysia, Melaka



My D-Link DSL2730E supports IPv6 but my current connection not capable to do the job
Boy96
post Oct 4 2013, 10:18 PM

That's a tripod.
*******
Senior Member
3,848 posts

Joined: Dec 2009
From: Ampang


Ok I have already enabled IPv6 on my DIR 615, whats next?

I check test-ipv6.com it shows I am still running on ipv4
JohnnyDicaprio
post Oct 4 2013, 11:01 PM

New Member
*
Junior Member
21 posts

Joined: Sep 2011
QUOTE(wKkaY @ Oct 4 2013, 10:07 PM)
2 scenarios I can think of:

1) router only supports dhcpv6, doesn't support slaac. solution: install dhcpv6 client in your debian box, eg wide-dhcpv6-client or dibbler.

2) router does support SLAAC, but it is disabled in your debian kernel /proc/sys/net settings
*
Found the culprit. It was my wireless card problem.

Maybe got some driver issue with debian, but no problem in windows.

Tried with cable and wireless usb, both can connect to ipv6.. thumbup.gif thumbup.gif
Anonymous34
post Oct 4 2013, 11:49 PM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(wKkaY @ Oct 1 2013, 12:35 AM)
I just heard that TMnet launched IPv6 on September 27th, so I did some experiments tonight and confirm that it is live!

Attached Image Attached Image Attached Image

What I've seen so far from packet dumps:
- PPP IPCP6 negotiates link-local addresses
- SLAAC Router Advertisement gives you a dynamically-assigned /64
- DHCPv6 assigns DNS servers

In addition, asellus reports that DHCPv6-PD is supported. The prefix delegated is dynamic.

DNS servers from DHCPv6:
- 2001:e68::b:68
- 2001:e68:2005:29:202:188:0:133 (does this look familiar? brows.gif )

Attached is a pcap of the IPv6 assignment process.

PDF doc from TMnet about enabling IPv6: http://www.tm.com.my/OnlineHelp/CustomerSu...able%20IPv6.pdf

Known working configurations:
- D-Link DSL-2730U
- D-Link DIR-615
- TP-Link WDR4300
- Mikrotik
- Windows 7 PPPoE
*
Just knew this news when I look at LYN's tag beside the post#xx number.
Haven't seen this post before, but then headed to: http://test-ipv6.com/ to test!
Sure enough, iPv6 is live on UniFi now!
TSwKkaY
post Oct 4 2013, 11:51 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(Anonymous34 @ Oct 4 2013, 11:49 PM)
Just knew this news when I look at LYN's tag beside the post#xx number.
Haven't seen this post before, but then headed to: http://test-ipv6.com/ to test!
Sure enough, iPv6 is live on UniFi now!
*
Welcome to IPv6 land smile.gif (PS: your sig is too tall, can you shorten it?)
Anonymous34
post Oct 4 2013, 11:53 PM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(wKkaY @ Oct 4 2013, 11:51 PM)
Welcome to IPv6 land smile.gif (PS: your sig is too tall, can you shorten it?)
*
Thank you!
Btw, will fix it right now hehe.
Anonymous34
post Oct 4 2013, 11:55 PM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(wKkaY @ Oct 4 2013, 11:51 PM)
Welcome to IPv6 land smile.gif (PS: your sig is too tall, can you shorten it?)
*
is my sig ok right now? hehe
btw, any IPv6 website for me to test it out?
I know the speed doesn't increase, but it's still good to check it out.
All I know about IPv6 is that it has a lot more bandwith than IPv4. tongue.gif
Eoma
post Oct 5 2013, 12:18 AM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(Anonymous34 @ Oct 4 2013, 11:55 PM)
is my sig ok right now? hehe
btw, any IPv6 website for me to test it out?
I know the speed doesn't increase, but it's still good to check it out.
All I know about IPv6 is that it has a lot more bandwith than IPv4.  tongue.gif
*
Here (and for everyone else too):

http://look4ipv6.appspot.com/tools/random
XeactorZ
post Oct 5 2013, 01:08 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(JohnnyDicaprio @ Oct 4 2013, 07:47 PM)
below are my config for l7 router
i can get ipv6 address for my windows 7 but not for my debian, dont know why.. rclxub.gif  rclxub.gif
i have to put image in spoiler, lazy to resize

» Click to show Spoiler - click again to hide... «


results
» Click to show Spoiler - click again to hide... «


thumbup.gif  thumbup.gif
*
I am using same router with you
but can I know how you update the firmware ?
and can guide me how to enable ipv6 ?
XeactorZ
post Oct 5 2013, 02:25 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
yes I successfully running ipv6
but what the benefit ?
although I study network course in my college LOL
Anonymous34
post Oct 5 2013, 10:34 AM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(XeactorZ @ Oct 5 2013, 02:25 AM)
yes I successfully running ipv6
but what the benefit ?
although I study network course in my college LOL
*
iPv6 provides more bandwith.
Video: http://www.youtube.com/watch?v=-Uwjt32NvVA
Google just makes it so simple laugh.gif
More info here:http://www.google.com/intl/en/ipv6/

This post has been edited by Anonymous34: Oct 5 2013, 10:38 AM
fbat
post Oct 5 2013, 10:41 AM

New Member
*
Junior Member
6 posts

Joined: Feb 2006
QUOTE(XeactorZ @ Oct 5 2013, 02:25 AM)
yes I successfully running ipv6
but what the benefit ?
although I study network course in my college LOL
*
How you managed to enable the dual lan?

Eoma
post Oct 5 2013, 11:52 AM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(Anonymous34 @ Oct 5 2013, 10:34 AM)
iPv6 provides more bandwith.
*
Lolwhat ? No lah.
jolmy
post Oct 5 2013, 12:17 PM

Meow
******
Senior Member
1,182 posts

Joined: Jan 2003


I'm more interested with custom routers that support UniFi with IPv6 support. As I know the TP-Link TL-WR841ND does NOT. Hope TP-Link will come out with one soon.
asellus
post Oct 5 2013, 01:23 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


I think any routers that has the image below at TP-LINK website can use TM's dual-stack implementation. I thought to buy one too because none of the TM-supplied modems I have supports it, and Mikrotik's IPv6 implementation is iffy most of the time.

user posted image
jolmy
post Oct 5 2013, 02:33 PM

Meow
******
Senior Member
1,182 posts

Joined: Jan 2003


QUOTE(asellus @ Oct 5 2013, 01:23 PM)
I think any routers that has the image below at TP-LINK website can use TM's dual-stack implementation. I thought to buy one too because none of the TM-supplied modems I have supports it, and Mikrotik's IPv6 implementation is iffy most of the time.

user posted image
*
Only problem is these routers will probably not work with TM UniFi unless otherwise stated.
XeactorZ
post Oct 5 2013, 03:28 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Anonymous34 @ Oct 5 2013, 10:34 AM)
iPv6 provides more bandwith.
Video: http://www.youtube.com/watch?v=-Uwjt32NvVA
Google just makes it so simple  laugh.gif
More info here:http://www.google.com/intl/en/ipv6/
*
ooo
but right now I disable it already
L7 router once enable ipv6, get frequent dc =_=
as my desktop LAN cable port got problem, I can't fix it sad.gif

QUOTE(fbat @ Oct 5 2013, 10:41 AM)
How you managed to enable the dual lan?
*
didn't enable
just update firmware then done

search inside the section, depends on your router
mine is router L7

This post has been edited by XeactorZ: Oct 5 2013, 03:30 PM
XeactorZ
post Oct 5 2013, 03:31 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
how about other router in order to enable the ipv6 ?
right now enable ipv6 again, see will get frequent dc or not ...

but need restart router or modem in order to enable ipv6
disable just untick only ....

This post has been edited by XeactorZ: Oct 5 2013, 03:34 PM
asellus
post Oct 5 2013, 04:31 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(jolmy @ Oct 5 2013, 02:33 PM)
Only problem is these routers will probably not work with TM UniFi unless otherwise stated.
*
Well, if the first page info about TP-Link WDR4300 being working fine, I think there should be nothing to worry about. At least TM used standardized protocols like ICMPv6 RA/RD and DHCPv6-PD at least to provide the dual-stack support.

wKkaY, maybe you can update us if DHCPv6-PD works now with UNIFI or not?
TSwKkaY
post Oct 5 2013, 04:35 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 5 2013, 04:31 PM)
Well, if the first page info about TP-Link WDR4300 being working fine, I think there should be nothing to worry about. At least TM used standardized protocols like ICMPv6 RA/RD and DHCPv6-PD at least to provide the dual-stack support.

wKkaY, maybe you can update us if DHCPv6-PD works now with UNIFI or not?
*
Unifi uses standardized protocols, however the specific combination of PPPoE over 802.1q is uncommon.

There's one member report that PD works, but where I am it doesn't.
Eoma
post Oct 5 2013, 08:37 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(jolmy @ Oct 5 2013, 12:17 PM)
I'm more interested with custom routers that support UniFi with IPv6 support. As I know the TP-Link TL-WR841ND does NOT. Hope TP-Link will come out with one soon.
*
There is a beta firmware for the 8980 though with a working dual stack implementation.


QUOTE(asellus @ Oct 5 2013, 01:23 PM)
I think any routers that has the image below at TP-LINK website can use TM's dual-stack implementation. I thought to buy one too because none of the TM-supplied modems I have supports it, and Mikrotik's IPv6 implementation is iffy most of the time.

user posted image
*
QUOTE(asellus @ Oct 5 2013, 04:31 PM)
Well, if the first page info about TP-Link WDR4300 being working fine, I think there should be nothing to worry about.
*
That info is misleading. It does not work correctly at the moment.
They have a seperate WANv4 and WANv6 dialer. Sent some emails to them, we'll see how it turns out.
The latest WDR4300 firmware for MY, has VLAN support but no IPv6 support (although it states it does on their page).


gogetter83
post Oct 5 2013, 11:29 PM

New Member
*
Junior Member
32 posts

Joined: Oct 2010
is the latency better on ipv6 currently?
soulfly
post Oct 6 2013, 12:04 AM

revving towards 10,000 rpm
Group Icon
VIP
15,903 posts

Joined: Jan 2003
From: Miri



am I IPv6 already?

user posted image
paultantk
post Oct 6 2013, 12:29 AM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Both dhcp6 and slaac doesn't work for me on pfsense. Wonder what I am doing wrong
TSwKkaY
post Oct 6 2013, 12:48 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(Eoma @ Oct 5 2013, 08:37 PM)
That info is misleading. It does not work correctly at the moment.
They have a seperate WANv4 and WANv6 dialer. Sent some emails to them, we'll see how it turns out.
The latest WDR4300 firmware for MY, has VLAN support but no IPv6 support (although it states it does on their page).
*
Oh sorry I saw that you were posting from IPv6 so I assumed that your WDR4300 is working. How were you posting at the time, were you using Windows PPPoE?
Eoma
post Oct 6 2013, 12:54 AM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(wKkaY @ Oct 6 2013, 12:48 AM)
Oh sorry I saw that you were posting from IPv6 so I assumed that your WDR4300 is working. How were you posting at the time, were you using Windows PPPoE?
*
It can get the WAN and LAN prefixes (separate from the standard v4 PPP).
However v6 only or "prefer-v6" sites won't load. youtube videos won't load for example. kame.net, microtik - not working.

Ly.net, test-ipv6 and even google v6 test shows "congrats" though. 50/50 working.
soulfly
post Oct 6 2013, 12:58 AM

revving towards 10,000 rpm
Group Icon
VIP
15,903 posts

Joined: Jan 2003
From: Miri



user posted image

icon_idea.gif
TSwKkaY
post Oct 6 2013, 01:10 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(soulfly @ Oct 6 2013, 12:04 AM)
am I IPv6 already?
*
What modem/router are you using? I'd like to add you to the database.
XeactorZ
post Oct 6 2013, 02:38 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
that weird, yesterday enable ipv6 keep frequent dc
so disable it
and after afternoon post re-enable it, no more frequent dc
using L7 router
ComposMentis
post Oct 6 2013, 10:01 AM

Casual
***
Junior Member
420 posts

Joined: May 2010
Testing ipv6 here smile.gif

dang, I think I missed something hmm.gif it's not shown as ipv6 hmm.gif

This post has been edited by ComposMentis: Oct 6 2013, 10:02 AM
ComposMentis
post Oct 6 2013, 10:59 AM

Casual
***
Junior Member
420 posts

Joined: May 2010
Strange, I have enabled ipv6 on the router but it appears that ipv4 is preferred over ipv6, anyone knows why?

Managed to get it work by disabling my ad blocking software, it seems to be the culprit hmm.gif

This post has been edited by ComposMentis: Oct 6 2013, 11:14 AM


Attached thumbnail(s)
Attached Image
asellus
post Oct 6 2013, 11:14 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(ComposMentis @ Oct 6 2013, 10:59 AM)
Strange, I have enabled ipv6 on the router but it appears that ipv4 is preferred over ipv6, anyone knows why?
*
Mozilla Firefox?
ComposMentis
post Oct 6 2013, 11:16 AM

Casual
***
Junior Member
420 posts

Joined: May 2010
QUOTE(asellus @ Oct 6 2013, 11:14 AM)
Mozilla Firefox?
*
It's working now after I disabled admuncher, I think it's responsible for the problem hmm.gif
fbat
post Oct 6 2013, 12:29 PM

New Member
*
Junior Member
6 posts

Joined: Feb 2006
QUOTE(XeactorZ @ Oct 6 2013, 02:38 AM)
that weird, yesterday enable ipv6 keep frequent dc
so disable it
and after afternoon post re-enable it, no more frequent dc
using L7 router
*
I try without update the firmware previously and have a no connection issue.

On one time where I managed to get IPV6 address, i noticed that the normal ipv4 WAN is disconnected.

Can you help to check whether is this also the case for you?
soulfly
post Oct 6 2013, 01:46 PM

revving towards 10,000 rpm
Group Icon
VIP
15,903 posts

Joined: Jan 2003
From: Miri



QUOTE(wKkaY @ Oct 6 2013, 01:10 AM)
What modem/router are you using? I'd like to add you to the database.
*
D-Link DSL-2730E supplied by TM, stock firmware.

Streamyx 4MBps here

This post has been edited by soulfly: Oct 6 2013, 01:47 PM
asellus
post Oct 6 2013, 06:00 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(ComposMentis @ Oct 6 2013, 11:16 AM)
It's working now after I disabled admuncher, I think it's responsible for the problem  hmm.gif
*
Nah, Firefox has this tendency to prefer IPv4 or IPv6 quite a lot. Chrome and IE doesn't have that problem.
XeactorZ
post Oct 6 2013, 06:08 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(fbat @ Oct 6 2013, 12:29 PM)
I try without update the firmware previously and have a no connection issue.

On one time where I managed to get IPV6 address, i noticed that the normal ipv4 WAN is disconnected.

Can you help to check whether is this also the case for you?
*
no this issue
Eoma
post Oct 6 2013, 06:31 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(asellus @ Oct 6 2013, 06:00 PM)
Nah, Firefox has this tendency to prefer IPv4 or IPv6 quite a lot. Chrome and IE doesn't have that problem.
*
Chrome does too. Sometimes you need to force DNSv6 in the about:net-internals page. Choose DNS-->Enable IPv6
InSplre
post Oct 6 2013, 07:55 PM

Look at all my stars!!
*******
Senior Member
2,816 posts

Joined: Jan 2003
From: kat situ kat sana


On Asus RT-N16
ComposMentis
post Oct 6 2013, 08:43 PM

Casual
***
Junior Member
420 posts

Joined: May 2010
QUOTE(asellus @ Oct 6 2013, 06:00 PM)
Nah, Firefox has this tendency to prefer IPv4 or IPv6 quite a lot. Chrome and IE doesn't have that problem.
*
Nope, tested and confirmed Ad muncher was the culprit, when I disabled Ad muncher and tested chrome and firefox again, they both used Ipv6. The same problem occurred when I re-enabled Ad muncher (both browsers switched to ipv4). Also, I noticed only IE 11 (apparently Ad muncher doesn't work with the latest IE) was running on Ipv6 when I enabled the program. I did a search on the net and turns out Ad muncher doesn't support Ipv6, probably it forces the browsers to run on Ipv4 for its ad blocking to work hmm.gif

This post has been edited by ComposMentis: Oct 6 2013, 10:45 PM
michaelkkl
post Oct 6 2013, 08:47 PM

Casual
***
Junior Member
362 posts

Joined: Jan 2011
Streamyx TM Modem TM6841G can support IPV6 too
Network--WAN--IPV6--Select Native--Save
Attached Image

This post has been edited by michaelkkl: Oct 8 2013, 10:43 AM
asellus
post Oct 6 2013, 11:36 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


Anyone here has problems accessing certain websites like Facebook and Yahoo when IPv6 is turned on?
tezro
post Oct 7 2013, 10:28 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 6 2013, 11:36 PM)
Anyone here has problems accessing certain websites like Facebook and Yahoo when IPv6 is turned on?
*
Hi,

I'm suggesting to all TM IPv6 users to try Google and OpenDNS IPv6 DNS servers.

Maybe it will influencing your IPv6 connection stability.

Google:


2001:4860:4860::8888
2001:4860:4860::8844

OpenDNS:


2620:0:ccc::2
2620:0:ccd::2

This post has been edited by tezro: Oct 7 2013, 10:32 AM
vinorgouki
post Oct 7 2013, 10:42 AM

Getting Started
**
Junior Member
120 posts

Joined: Jan 2003


how come i cant access to facebook and youtube video wont load if i connect to ipv6?
asellus
post Oct 7 2013, 11:04 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(tezro @ Oct 7 2013, 10:28 AM)
Hi,

I'm suggesting to all TM IPv6 users to try Google and OpenDNS IPv6 DNS servers.

Maybe it will influencing your IPv6 connection stability.

Google:
    2001:4860:4860::8888
    2001:4860:4860::8844

OpenDNS:
2620:0:ccc::2
2620:0:ccd::2
*
This doesn't work, I already used the Google IPv6 DNS servers. Facebook and YouTube videos (Youtube itself will still load) simply doesn't load here. Google website itself and others like Gmail has no problems.


QUOTE(vinorgouki @ Oct 7 2013, 10:42 AM)
how come i cant access to facebook and youtube video wont load if i connect to ipv6?
*
You and I are not the only ones.
Eoma
post Oct 7 2013, 11:15 AM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


Same problem on the WDR4300 that i faced. I think it's a firmware issue.

Just had a quick test on the Dlink 615 (on OpenWRT though) and both facebook and youtube work fine.
vinorgouki
post Oct 7 2013, 11:31 AM

Getting Started
**
Junior Member
120 posts

Joined: Jan 2003


QUOTE(asellus @ Oct 7 2013, 11:04 AM)
You and I are not the only ones.
*
even my handset and ipad cannot connect to facebook and youtube too (using app).
what router are u using bro? im using linksys x3000.
asellus
post Oct 7 2013, 11:33 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(vinorgouki @ Oct 7 2013, 11:31 AM)
even my handset and ipad cannot connect to facebook and youtube too (using app).
what router are u using bro? im using linksys x3000.
*
It is routerOS.
Sites that use cloudflare and has enabled IPv6 access also inaccessible. Cloudflare also cannot be accessed because of this.
tezro
post Oct 7 2013, 11:44 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 7 2013, 11:04 AM)
This doesn't work, I already used the Google IPv6 DNS servers. Facebook and YouTube videos (Youtube itself will still load) simply doesn't load here. Google website itself and others like Gmail has no problems.
You and I are not the only ones.
*
Try using Google Chrome to watch Youtube. unsure.gif

As for Facebook, i'm not sure.
asellus
post Oct 7 2013, 12:45 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(tezro @ Oct 7 2013, 11:44 AM)
Try using Google Chrome to watch Youtube.  unsure.gif

As for Facebook, i'm not sure.
*
Tried with Chrome 30 on my Windows 7 laptop, still not working.
tezro
post Oct 7 2013, 12:55 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 7 2013, 12:45 PM)
Tried with Chrome 30 on my Windows 7 laptop, still not working.
*
This problem probably originate from TM side. sweat.gif

Eoma
post Oct 7 2013, 03:43 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


For those with Facebook/Youtube video issues - try reducing your MTU to 1452.

http://wiki.openwrt.org/doc/howto/ipv6
asellus
post Oct 7 2013, 04:12 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Eoma @ Oct 7 2013, 03:43 PM)
For those with Facebook/Youtube video issues - try reducing your MTU to 1452.

http://wiki.openwrt.org/doc/howto/ipv6
*
Assuming the MTU should be changed at PPPoE interface, it didn't work too. I think this is TM problem.
Eoma
post Oct 7 2013, 04:25 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


I have a few friends with working dual stack connections. Some stock Unifi / Streamyx router/modems and some on 3rd party APs (belkin/TP Link) with either Open/DD WRT or manufacturer provided beta firmware

Friend on the OPEN WRT CPE suggested the MTU since he had that issue and was fixed after changing the MTU.

We need more reports and samples actually.

p/s: I'll try on mine after getting back tonight.
TSwKkaY
post Oct 7 2013, 05:37 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
An MTU problem is definitely possible, if your router's IPv6 implementation doesn't clamp MSS to MTU.

The easiest way to figure this out is to use a client *nix OS which lets you fiddle with MTU easily laugh.gif
amirsubhi
post Oct 7 2013, 06:22 PM

The Power Is IN Your Hand!
******
Senior Member
1,472 posts

Joined: Apr 2005
From: SumwHeRe In MaLaYsIa



Tested my Asus RT-N12 C1 Ver 3.0.0.4.374_813 with Unifi

and IPv6 connected rclxm9.gif

» Click to show Spoiler - click again to hide... «

tezro
post Oct 7 2013, 07:11 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(amirsubhi @ Oct 7 2013, 06:22 PM)
Tested my Asus RT-N12 C1 Ver 3.0.0.4.374_813 with Unifi

and IPv6 connected  rclxm9.gif

» Click to show Spoiler - click again to hide... «

*
amirsubhi,

Is this your router model? >>> RT-N12

I'm interested to get one for my house.
asellus
post Oct 7 2013, 07:39 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(amirsubhi @ Oct 7 2013, 06:22 PM)
Tested my Asus RT-N12 C1 Ver 3.0.0.4.374_813 with Unifi

and IPv6 connected  rclxm9.gif

» Click to show Spoiler - click again to hide... «

*
I have that router too. Did you install dd-wrt on it?
DellMalaysia
post Oct 7 2013, 10:35 PM

Kindly look at my previous successful threads
*****
Senior Member
735 posts

Joined: Sep 2013
From: IYD ~ In Your Dream



Am I on IPv6?

Yay success! But why page loading so slow?

This post has been edited by DellMalaysia: Oct 7 2013, 10:37 PM
XeactorZ
post Oct 7 2013, 11:11 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
Anybody facing frequent dc ?
Even i diaable ipv6 still same, what wrong ?
asellus
post Oct 7 2013, 11:19 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(XeactorZ @ Oct 7 2013, 11:11 PM)
Anybody facing frequent dc ?
Even i diaable ipv6 still same, what wrong ?
*
PPPoE DC? Didn't happen here.
amirsubhi
post Oct 8 2013, 12:17 AM

The Power Is IN Your Hand!
******
Senior Member
1,472 posts

Joined: Apr 2005
From: SumwHeRe In MaLaYsIa



QUOTE(tezro @ Oct 7 2013, 07:11 PM)
amirsubhi,

Is this your router model? >>> RT-N12

I'm interested to get one for my house.
*
mine was this C1, the version after the one you post

http://www.asus.com/my/Networking/RTN12_C1/

QUOTE(asellus @ Oct 7 2013, 07:39 PM)
I have that router too. Did you install dd-wrt on it?
*
Nope, stock Asus-WRT Ver 3.0.0.4.374_813 can be download directly from Asus website.

This post has been edited by amirsubhi: Oct 8 2013, 12:23 AM
XeactorZ
post Oct 8 2013, 01:49 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(asellus @ Oct 7 2013, 11:19 PM)
PPPoE DC? Didn't happen here.
*
ya pppoe
no idea what wrong
now disable ipv6, let see how ...
Alpha_Tay
post Oct 8 2013, 05:06 AM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
test report for TM TM6841G Zyxel P-660HW T1 V3

this router has frequency auto reboot problem sometimes even when not using the router to access internet heavily or long hour as report by other streamyx user previously.

router configuration for ipv6

QUOTE(michaelkkl @ Oct 6 2013, 08:47 PM)
Streamyx TM Modem TM6841G can support IPV6 too
Network--WAN--IPV6--Select Native--Save
[attachmentid=3663003]
*
as shown here, after setting IPv6 Mode to Native, but still need to DHCPv6 Client to Enable & tick Prefix Delegation & tick DNS Server, so not only the pppoe connection get ipv6 ip, the router also get ipv6 ip, and all the connected client via lan would also get ipv6 ip. the connected wifi client doesnt seem to get ipv6 ip, not sure if it is the router problem or the wifi adapter problem.

this router was the result of cooperation between Zyxel and TM, it has special firmware, it also has /half/ hard coded TM ipv4 dns server 202.188.0.133 202.188.1.5

not sure is it due to /half/ hard coded TM ipv4 dns server, the DNS servers from DHCPv6: - 2001:e68::b:68 - 2001:e68:2005:29:202:188:0:133 wont show up at this router and all the connected client. if choose dns obtained from ISP at WAN setting, the default dns ip address was as usual 1.9.1.9 202.188.0.133, result from http://test-ipv6.com/ is 9/10, Test if your ISP's DNS server uses IPv6 = no. if manually setting dns server to google ipv4 and ipv6 at the computer, the result would be 10/10.

if manually setting dns server to DNS servers from DHCPv6: - 2001:e68::b:68 - 2001:e68:2005:29:202:188:0:133 at the computer, the result would be 0/10 as shown at this picture.
» Click to show Spoiler - click again to hide... «


if setting the router DHCPv6 at LAN configuration to 2001:e68::b:68 2001:e68:2005:29:202:188:0:133, the router DHCPv4 wouldnt work, connected client couldnt get any DHCPv4 ip, has to reset the router or setting ip manually at the computer to access the router again.

couldnt access http://whatismyv6.com/ with this router, not matter IPv4 only Test Normal Test IPv6 only Test
soulfly
post Oct 8 2013, 11:17 AM

revving towards 10,000 rpm
Group Icon
VIP
15,903 posts

Joined: Jan 2003
From: Miri



I noticed that with IPv6 running, OpenDNS filtering doesn't work, and the OpenDNS Updater tool won't update the IP address either.

IPv6 is working fine, and router setting shows the correct OpenDNS' DNS and stuffs, but not on my PC. My network connection detail shows that I am using TMnet DNS instead of OpenDNS on the router.

The only way to get OpenDNS filtering working is by disabling TCP/IPv6 in network connection properties, which basically disables IPv6 on your PC. No need to change the router setting if you still want IPv6 on other devices.

So, if you want OpenDNS filtering, no choice but to use IPv4 only.

nwk
post Oct 8 2013, 05:06 PM

Getting Started
**
Junior Member
256 posts

Joined: Sep 2006
From: Britannia
my area don't have IPv6. sad.gif

This post has been edited by nwk: Oct 8 2013, 05:07 PM
aneip
post Oct 8 2013, 10:20 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


QUOTE(soulfly @ Oct 8 2013, 11:17 AM)
I noticed that with IPv6 running, OpenDNS filtering doesn't work, and the OpenDNS Updater tool won't update the IP address either.

IPv6 is working fine, and router setting shows the correct OpenDNS' DNS and stuffs, but not on my PC. My network connection detail shows that I am using TMnet DNS instead of OpenDNS on the router.

The only way to get OpenDNS filtering working is by disabling TCP/IPv6 in network connection properties, which basically disables IPv6 on your PC. No need to change the router setting if you still want IPv6 on other devices.

So, if you want OpenDNS filtering, no choice but to use IPv4 only.
*
Maybe because every computer got their own public IP rather than NATed to 1 ipv4.
aneip
post Oct 9 2013, 02:00 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


Still cannot get my area to works.. Only thing working is 6to4 both on windows 7 and pfsense.. Currently using that.. No problem connecting to free ipv6 newsgroup.. Got full 10mbps..
amirsubhi
post Oct 9 2013, 07:04 PM

The Power Is IN Your Hand!
******
Senior Member
1,472 posts

Joined: Apr 2005
From: SumwHeRe In MaLaYsIa



Gombak/Batu havent supported IPv6? Mine DLINK DIR7.15 connected to VDSL Huawei can't get IPv6 yet

This post has been edited by amirsubhi: Oct 9 2013, 07:04 PM
tezro
post Oct 10 2013, 12:44 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(amirsubhi @ Oct 9 2013, 07:04 PM)
Gombak/Batu havent supported IPv6? Mine DLINK DIR7.15 connected to VDSL Huawei can't get IPv6 yet
*
So, currently, you're using IPv6 tunnel?
changchingyew
post Oct 15 2013, 10:32 AM

New Member
*
Newbie
0 posts

Joined: Oct 2013
Got v6 on Streamyx 4Mbps here in Penang too

Spent some time got it running with latest openwrt.org Barrier Breaker snapshot

Attached Image

Attached Image
paultantk
post Oct 15 2013, 04:19 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


Still no IPV6 here at Bukit Jelutong Shah Alam.
Anime4000
post Oct 15 2013, 09:50 PM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


This IPv6, all connected device get unique WAN IPv6 ? or still single WAN IPv6 on router?
asellus
post Oct 15 2013, 10:29 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Anime4000 @ Oct 15 2013, 09:50 PM)
This IPv6, all connected device get unique WAN IPv6 ? or still single WAN IPv6 on router?
*
One or two WAN IPv6 unique address(es) per device, depending on how the device is configured.
tezro
post Oct 15 2013, 11:55 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 15 2013, 10:29 PM)
One or two WAN IPv6 unique address(es) per device, depending on how the device is configured.
*
Is this mean TM will not allocating static IPv6 addresses to home users?

What's your opinion, asellus?

Anime4000
post Oct 16 2013, 02:11 AM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


QUOTE(asellus @ Oct 15 2013, 10:29 PM)
One or two WAN IPv6 unique address(es) per device, depending on how the device is configured.
*
basically, like this?
Attached Image
What I see, there are no more "NAT" like IPv4, and have Two WAN IPv6, and One IPv6 Local...
more like Device to Device -or- Computer to Computer directly...
Soon in future game, no more UPNP or opening port? since every device have WAN IP...

I try help my friend enable his IPv6, since my router can't have IPv6.... so this what I do.
Attached Image
Enable... and Delegation
Attached Image
This look like forward WAN IP to internal LAN
prefix... 64bit?

This post has been edited by Anime4000: Oct 16 2013, 02:23 AM
tezro
post Oct 16 2013, 02:43 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(Anime4000 @ Oct 16 2013, 02:11 AM)
basically, like this?
Attached Image
What I see, there are no more "NAT" like IPv4, and have Two WAN IPv6, and One IPv6 Local...
more like Device to Device -or- Computer to Computer directly...
Soon in future game, no more UPNP or opening port? since every device have WAN IP...

I try help my friend enable his IPv6, since my router can't have IPv6.... so this what I do.
Attached Image
Enable... and Delegation
Attached Image
This look like forward WAN IP to internal LAN
prefix... 64bit?
*
Yes............. /64
Anime4000
post Oct 16 2013, 03:28 AM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


QUOTE(tezro @ Oct 16 2013, 02:43 AM)
Yes............. /64
*
is mean, Subnet mask is ffff:ffff:ffff:ffff:::::
is like who in "2001:e68:4022:5136/64" like big LAN for country...

IPv6 no more NAT... like this?
Attached Image
Article: No NAT in IPv6?

This post has been edited by Anime4000: Oct 16 2013, 03:50 AM
tezro
post Oct 16 2013, 06:38 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(Anime4000 @ Oct 16 2013, 03:28 AM)
is mean, Subnet mask is ffff:ffff:ffff:ffff:::::
is like who in "2001:e68:4022:5136/64" like big LAN for country...

IPv6 no more NAT... like this?
Attached Image
Article: No NAT in IPv6?
*
Yes. No NAT in IPv6. So each clients in your friend network or the gateway must have a firewall setup correctly.

This post has been edited by tezro: Oct 16 2013, 06:42 AM
MX510
post Oct 16 2013, 07:08 AM

Love Me Sin Hate Me Sinner
*******
Senior Member
4,038 posts

Joined: Aug 2005
From: Earth



I got meeting with TM any issues can let me sort with them asap :-)
powerwoot
post Oct 16 2013, 07:30 AM

讨厌的 ubuntu
*******
Senior Member
2,930 posts

Joined: Jan 2007
From: Kolej Universiti Agrosains Malaysia, Melaka



QUOTE(changchingyew @ Oct 15 2013, 10:32 AM)
Got v6 on Streamyx 4Mbps here in Penang too

Spent some time got it running with latest openwrt.org Barrier Breaker snapshot

Attached Image

Attached Image
*
Good to see that, but my area haven't supported IPv6 yet even I've enabled it from my router D-Link DSL-2730E. So my result is 0/10.
vincent_ng86
post Oct 16 2013, 07:40 AM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


QUOTE(asellus @ Oct 7 2013, 11:04 AM)
This doesn't work, I already used the Google IPv6 DNS servers. Facebook and YouTube videos (Youtube itself will still load) simply doesn't load here. Google website itself and others like Gmail has no problems.
You and I are not the only ones.
*
Same here. Any solutions so far?

This post has been edited by vincent_ng86: Oct 16 2013, 07:44 AM
tezro
post Oct 16 2013, 07:50 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(vincent_ng86 @ Oct 16 2013, 07:40 AM)
Same here. Any solutions so far?
*
Can you test your native IPv6 connection by visiting this website? ipv6chicken
tezro
post Oct 16 2013, 08:23 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(MX510 @ Oct 16 2013, 07:08 AM)
I got meeting with TM any issues can let me sort with them asap :-)
*
Hi MX510. Can you ask TM will they allocating static IPv6 prefix higher than /64 for home user?

This is the most important thing that i want to know.

Thank you.
asellus
post Oct 16 2013, 08:37 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(tezro @ Oct 15 2013, 11:55 PM)
Is this mean TM will not allocating static IPv6 addresses to home users?

What's your opinion, asellus?
*
I don't mind not having static prefixes, but i for sure would like a larger one like /60 or /56. For me larger prefixes is better than static /64 prefix.


QUOTE(Anime4000 @ Oct 16 2013, 02:11 AM)
basically, like this?
Attached Image
What I see, there are no more "NAT" like IPv4, and have Two WAN IPv6, and One IPv6 Local...
more like Device to Device -or- Computer to Computer directly...
Soon in future game, no more UPNP or opening port? since every device have WAN IP...

I try help my friend enable his IPv6, since my router can't have IPv6.... so this what I do.
Attached Image
Enable... and Delegation
Attached Image
This look like forward WAN IP to internal LAN
prefix... 64bit?
*
Yes, it works like that.
tezro
post Oct 16 2013, 08:48 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 16 2013, 08:37 AM)
I don't mind not having static prefixes, but i for sure would like a larger one like /60 or /56. For me larger prefixes is better than static /64 prefix.
Yes, it works like that.
*
Yes, you're correct, asellus. I'm stumped when they assigning /64 to end users. doh.gif

Haha...the moment i'm using the TM native IPv6, i'm unable to set a static native IPv6 from TM for my router and PC. rclxub.gif

asellus
post Oct 16 2013, 09:10 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(vincent_ng86 @ Oct 16 2013, 07:40 AM)
Same here. Any solutions so far?
*
No, no solution so far except drastic ones that I have employed which highly likely will not apply to you.

QUOTE(tezro @ Oct 16 2013, 07:50 AM)
Can you test your native IPv6 connection by visiting this website? ipv6chicken
*
Works just fine here. Facebook still will not open.
tezro
post Oct 16 2013, 09:47 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 16 2013, 09:10 AM)
Works just fine here. Facebook still will not open.
*
Not sure what's exactly happened at TM side.

Currently, i'm using Hurricane Electric IPv6 tunnel for my IPv6 connection.

Maybe reading this YouTube video buffering issue on IPv6 enabled networks blogspot entry can give you hint on how to fix the problem.

MX510
post Oct 16 2013, 10:48 AM

Love Me Sin Hate Me Sinner
*******
Senior Member
4,038 posts

Joined: Aug 2005
From: Earth



QUOTE(tezro @ Oct 16 2013, 08:23 AM)
Hi MX510. Can you ask TM will they allocating static IPv6 prefix higher than /64 for home user?

This is the most important thing that i want to know.

Thank you.
*
Noted anything else?
tezro
post Oct 16 2013, 11:12 AM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(MX510 @ Oct 16 2013, 10:48 AM)
Noted anything else?
*
That's all from me. Thanks for your willingness to tell TM about this matter. thumbup.gif
asellus
post Oct 16 2013, 01:29 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(tezro @ Oct 16 2013, 09:47 AM)
Not sure what's exactly happened at TM side.

Currently, i'm using Hurricane Electric IPv6 tunnel for my IPv6 connection.

Maybe reading this YouTube video buffering issue on IPv6 enabled networks blogspot entry can give you hint on how to fix the problem.
*
OMG, MSS clamping to 1392 DOES THE TRICK!

Attached Image

I've tried MSS clamping before, but not at 1392, therefore I assume MSS clamping will not solve the problem.
wKkaY should add this to the front page - no need for people to have problems like this.
TSwKkaY
post Oct 16 2013, 01:47 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 16 2013, 01:29 PM)
OMG, MSS clamping to 1392 DOES THE TRICK!

Attached Image

I've tried MSS clamping before, but not at 1392, therefore I assume MSS clamping will not solve the problem.
wKkaY should add this to the front page - no need for people to have problems like this.
*
Typically one would clamp it to PMTU and let the kernel do the math. Do you have the option for that?
asellus
post Oct 16 2013, 01:58 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Oct 16 2013, 01:47 PM)
Typically one would clamp it to PMTU and let the kernel do the math. Do you have the option for that?
*
Mikrotik can do that, but only for IPv4 traffic. For IPv6, MSS clamping has to be done manually.
TSwKkaY
post Oct 16 2013, 02:06 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 16 2013, 01:58 PM)
Mikrotik can do that, but only for IPv4 traffic. For IPv6, MSS clamping has to be done manually.
*
Mine seems to have it. I can add the mangle rule, although I can't confirm whether it actually works. Version 6.4 FWIW.
TSwKkaY
post Oct 16 2013, 02:09 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Having said that, technically it's not pure in the sense that there's something in the middle meddling with the IP payload. Lemme see whether there's any IPv6 spec that addresses the PMTU problem.
asellus
post Oct 16 2013, 02:14 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Oct 16 2013, 02:06 PM)
Mine seems to have it. I can add the mangle rule, although I can't confirm whether it actually works. Version 6.4 FWIW.
*
If I set up the PPP profile to change the MSS, Mikrotik will only add two rules in "/ip firewall mangle" section. The "/ipv6 firewall mangle" section will still be empty. This is a known issue with routerOS as shown at http://forum.mikrotik.com/viewtopic.php?f=2&t=51117 amongst other places.

Do you know how to tell routerOS to add the appropriate rules to "/ipv6 firewall mangle" when change MSS is enabled in the PPP profile?
tezro
post Oct 16 2013, 02:27 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


@asellus Are you using Streamyx 2Mbps? Just want to know. smile.gif
TSwKkaY
post Oct 16 2013, 02:34 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 16 2013, 02:14 PM)
If I set up the PPP profile to change the MSS, Mikrotik will only add two rules in "/ip firewall mangle" section. The "/ipv6 firewall mangle" section will still be empty. This is a known issue with routerOS as shown at http://forum.mikrotik.com/viewtopic.php?f=2&t=51117 amongst other places.

Do you know how to tell routerOS to add the appropriate rules to "/ipv6 firewall mangle" when change MSS is enabled in the PPP profile?
*
Oh I didn't know they would add those rules automatically. Mine doesn't add them for IPv4. In Linux, the MTU mangling is normally done in rp-pppoe userspace client, so it isn't necessary to create iptables rules. I don't know if Mikrotik uses the same pppoe client implementation.

So now I understand what you mean by "manually". What I meant wasn't automatic as in remove the need to manually add clamping rules. Just to remove the manual MSS calculation, by using a rule like:
QUOTE
chain=postrouting action=change-mss new-mss=clamp-to-pmtu passthrough=yes protocol=tcp tcp-flags=syn XXX-interface=unifi

MX510
post Oct 16 2013, 02:53 PM

Love Me Sin Hate Me Sinner
*******
Senior Member
4,038 posts

Joined: Aug 2005
From: Earth



QUOTE(wKkaY @ Oct 16 2013, 02:34 PM)
Oh I didn't know they would add those rules automatically. Mine doesn't add them for IPv4. In Linux, the MTU mangling is normally done in rp-pppoe userspace client, so it isn't necessary to create iptables rules. I don't know if Mikrotik uses the same pppoe client implementation.

So now I understand what you mean by "manually". What I meant wasn't automatic as in remove the need to manually add clamping rules. Just to remove the manual MSS calculation, by using a rule like:
*
Hehehe nice one bro :-) dunno got another admin playing with mikrotik also


asellus
post Oct 16 2013, 03:08 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Oct 16 2013, 02:34 PM)
Oh I didn't know they would add those rules automatically. Mine doesn't add them for IPv4. In Linux, the MTU mangling is normally done in rp-pppoe userspace client, so it isn't necessary to create iptables rules. I don't know if Mikrotik uses the same pppoe client implementation.

So now I understand what you mean by "manually". What I meant wasn't automatic as in remove the need to manually add clamping rules. Just to remove the manual MSS calculation, by using a rule like:
*
In routerOS, to do MSS clamping, you have to use iptables and/or ip6tables. The PPPoE dialer of routerOS lacks many features that even D-Link DIR-615 dialer has.

Your rule seems to works though. Although I wonder why MSS clamping to 1432 that I done earlier doesn't work, while it works with 1392.
asellus
post Oct 16 2013, 03:11 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(tezro @ Oct 16 2013, 02:27 PM)
@asellus Are you using Streamyx 2Mbps? Just want to know. smile.gif
*
I have Streamyx BB 4MB and BB 1MB. Both works well with IPv6.
TSwKkaY
post Oct 16 2013, 03:13 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 16 2013, 03:08 PM)
Your rule seems to works though. Although I wonder why MSS clamping to 1432 that I done earlier doesn't work, while it works with 1392.
*
When I'm free (after I catch up to all the work I missed from being sick) I'll set up an experiment to figure out this MTU problem. In theory... PMTU discovery should address this. But why isn't it?
vincent_ng86
post Oct 16 2013, 03:17 PM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


QUOTE(asellus @ Oct 16 2013, 09:10 AM)
No, no solution so far except drastic ones that I have employed which highly likely will not apply to you.
Works just fine here. Facebook still will not open.
*
Thanks for sharing. Was wondering all the while was is going on. Didn't expect the implementation of IPV6 bringing this kind of impact.
tezro
post Oct 16 2013, 03:19 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(MX510 @ Oct 16 2013, 02:53 PM)
Hehehe nice one bro :-) dunno got another admin playing with mikrotik also
*
Hi MX510. May i know what is the TM answer for my question?

Thank you.
asellus
post Oct 16 2013, 03:29 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(vincent_ng86 @ Oct 16 2013, 03:17 PM)
Thanks for sharing. Was wondering all the while was is going on. Didn't expect the implementation of IPV6 bringing this kind of impact.
*
Actually, clamping the MSS to 1392 seems to work. What router did you use?
tezro
post Oct 16 2013, 03:32 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(asellus @ Oct 16 2013, 03:11 PM)
I have Streamyx BB 4MB and BB 1MB. Both works well with IPv6.
*
Ooo, ok. I wish i can upgrade my line to Streamyx 4 Mbps soon. icon_rolleyes.gif
Anime4000
post Oct 16 2013, 05:09 PM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


my router DIR-605L seem don't have IPv6 support.. btw I tried this way:
Attached Image

But... can't pinging:
Attached Image

This post has been edited by Anime4000: Oct 16 2013, 05:12 PM
tezro
post Oct 16 2013, 05:51 PM

New Member
*
Junior Member
30 posts

Joined: Oct 2009


QUOTE(Anime4000 @ Oct 16 2013, 05:09 PM)
my router DIR-605L seem don't have IPv6 support.. btw I tried this way:
Attached Image

But... can't pinging:
Attached Image
*
Can you try ping to other websites? As example, he.net

Alpha_Tay
post Oct 16 2013, 06:30 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(Anime4000 @ Oct 16 2013, 05:09 PM)
my router DIR-605L seem don't have IPv6 support.. btw I tried this way:
Attached Image

But... can't pinging:
Attached Image
*
the way of yr config work for me, dunno why it doesnt work for u, show us your router config.
vincent_ng86
post Oct 16 2013, 07:18 PM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


QUOTE(asellus @ Oct 16 2013, 03:29 PM)
Actually, clamping the MSS to 1392 seems to work. What router did you use?
*
Hmm, will try to work on that when I am back home later this evening. Using the router provided by TM, i.e.: DIR-615.
Anime4000
post Oct 16 2013, 09:40 PM

Look at all my stars!!
*******
Senior Member
2,399 posts

Joined: Jul 2009
From: /dev/null


QUOTE(Alpha_Tay @ Oct 16 2013, 06:30 PM)
the way of yr config work for me, dunno why it doesnt work for u, show us your router config.
*
My router was DIR-605L. Dont have IPv6...
Attached Image
Alpha Wolf
post Oct 17 2013, 07:08 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 7 2013, 11:11 PM)
Anybody facing frequent dc ?
Even i diaable ipv6 still same, what wrong ?
*
Could it be an issue with the newer 1.06TM firmware you've upgraded to? 1.01TM runs really stable for me and I am looking around for this version of the firmware so that I can revert back to it. I don't want to get stuck at 1.06TM after trying it.
XeactorZ
post Oct 17 2013, 04:29 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 17 2013, 07:08 AM)
Could it be an issue with the newer 1.06TM firmware you've upgraded to? 1.01TM runs really stable for me and I am looking around for this version of the firmware so that I can revert back to it. I don't want to get stuck at 1.06TM after trying it.
*
no idea have been disable ipv6 for few days
no frequent dc issue for this few days
and before I upgrade to 1.06 firmware I do a backup during 1.01 firmware already
fbat
post Oct 17 2013, 08:03 PM

New Member
*
Junior Member
6 posts

Joined: Feb 2006
QUOTE(XeactorZ @ Oct 17 2013, 04:29 PM)
no idea have been disable ipv6 for few days
no frequent dc issue for this few days
and before I upgrade to 1.06 firmware I do a backup during 1.01 firmware already
*
How you backup the 1.01 firmware?

Alpha_Tay
post Oct 17 2013, 11:35 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(Anime4000 @ Oct 16 2013, 05:09 PM)
my router DIR-605L seem don't have IPv6 support.. btw I tried this way:
Attached Image

But... can't pinging:
Attached Image
*
QUOTE(Anime4000 @ Oct 16 2013, 09:40 PM)
My router was DIR-605L. Dont have IPv6...
Attached Image
*
then it could be yr windows config? or yr firewall or other software blocking it?
XeactorZ
post Oct 18 2013, 01:00 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(fbat @ Oct 17 2013, 08:03 PM)
How you backup the 1.01 firmware?
*
login using below details
user: operator
passw: h566UniFi

go tools > system > save to local hard drive
that cfg.bin should be the firmware backup, didn't try myself
Alpha Wolf
post Oct 18 2013, 01:51 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 17 2013, 04:29 PM)
no idea have been disable ipv6 for few days
no frequent dc issue for this few days
and before I upgrade to 1.06 firmware I do a backup during 1.01 firmware already
*
Yes, that is just the configuration backup. But what if you want to downgrade to 1.01 firmware? Because 1.06 might be the culprit for frequent dc. I had no dc issues with 1.01
JohnLai
post Oct 18 2013, 04:24 PM

Skeptical Cat
*******
Senior Member
3,669 posts

Joined: Apr 2006
QUOTE(Anime4000 @ Oct 16 2013, 02:11 AM)
basically, like this?
Attached Image
What I see, there are no more "NAT" like IPv4, and have Two WAN IPv6, and One IPv6 Local...
more like Device to Device -or- Computer to Computer directly...
Soon in future game, no more UPNP or opening port? since every device have WAN IP...

I try help my friend enable his IPv6, since my router can't have IPv6.... so this what I do.
Attached Image
Enable... and Delegation
Attached Image
This look like forward WAN IP to internal LAN
prefix... 64bit?
*
rclxms.gif
My initial test of enabling IPV6 with D-Link DSL-2750U ended up in failure even though I enabled IPV6, Request Address and Prefix.

It turns out I must CHECK the Enable RADVD for IPV6 to work its magic.

thumbup.gif Thanks for the screenshot.

EDIT: Btw, how to visit IPV6 enabled https lowyat forum? My browser passes the test-ipv6.com with full score and I just posted this post, how come I didnt get the unique 'IPV6' logo at the top right?

This post has been edited by JohnLai: Oct 18 2013, 04:30 PM
rizvanrp
post Oct 18 2013, 04:39 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



Mikrotik Unifi PPPoE IPV6 configuration (tested on RB750 ROS 5.17 + BSRBRF01)

Prerequisites :

i. IPV6 RouterOS modules loaded in System -> Packages (Winbox)
ii. PPPoE Client profile (default) must have IPV6 set to Yes n PPP -> Profiles -> 'default' -> Protocols (Use IPv6 = Yes)

1. Replace "ether1_vlan500_UNIFI" with the name of your Unifi PPPoE client interface :

In terminal :

CODE
/ipv6 dhcp-client add interface="ether1_vlan500_UNIFI" pool-name="pppoev6" disabled=no


2. Terminal on my RouterOS says the commands for IPv6 addressing are invalid .. so use Winbox GUI and go into :

CODE
IPv6 -> Addresses

Add a new IPv6 address :

Address = ::/64
From Pool = pppoev6
Interface = ether2-local-master (replace with your LAN switch master port)
EUI64 = No
Advertise = Yes


3. Disable and enable your PPPoE client interface. It should get a new DHCPv6 prefix which will propagate to your IPv6 address list and LAN clients.

CODE
/interface pppoe-client disable ether1_vlan500_UNIFI; /interface pppoe-client enable ether1_vlan500_UNIFI

...

Reconnect your LAN clients and it should auto negotiate an IPv6 address for them.

** Do not set static /64 prefixes, they appear to be dynamic and unique to your PPPoE session ID and will change upon reconnect.

TCP MSS Fix :

As pointed out by wKkaY, use the MTU flag in the IPv6 RA to advertise the proper link MTU to your clients :

In Winbox :

IPv6 -> ND

Select your default ND (operates on 'all' interfaces by default), change the MTU option to 1480 (or whatever your PPPoE MTU is) :

user posted image

Old MSS mangle fix below (don't use this unless the above method isn't working for you) :
» Click to show Spoiler - click again to hide... «


Faster prefix expiry :

IPv6 -> ND -> Prefixes tab -> Default

Set a 2H/1H valid/preferred lifetime for your prefixes :

user posted image


Firewall Configuration (Security):

Enabling the IPv6 stack means no NAT to protect you and no firewall rules (by default) to prevent someone from hitting your Mikrotik login at ::0 or your devices behind the router. Setup these firewall rules to protect your network.

Replace "ether1_vlan500_UNIFI" with the name of your Unifi PPPoE client interface :

CODE
/ipv6 firewall filter add action=accept chain=input connection-state=established disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=forward connection-state=established disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=input connection-state=related disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=forward connection-state=related disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=input disabled=no dst-port=546 in-interface=ether1_vlan500_UNIFI protocol=udp src-address=fe80::/16
/ipv6 firewall filter add action=drop chain=input disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=drop chain=forward disabled=no in-interface=ether1_vlan500_UNIFI

** input chain rules affect traffic heading to ::0 (your router's public IPv6), forward chain rules affect traffic from your clients behind the router

** Updated firewall rules to whitelist DHCPv6 packets

** MTU value tag used rather than iptables6 mangle for TCP MSS fixing

** Lower prefix expiry (30days/7days vs 2hours/1hour) to match Unifi's dynamic IPv6 prefix distribution

This post has been edited by rizvanrp: Oct 21 2013, 08:40 PM
XeactorZ
post Oct 18 2013, 06:14 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 18 2013, 01:51 PM)
Yes, that is just the configuration backup. But what if you want to downgrade to 1.01 firmware? Because 1.06 might be the culprit for frequent dc. I had no dc issues with 1.01
*
no idea
so far now didn't facing frequent dc issue on 1.06 firmware with disable ipv6
yet, by the time I using 1.01 firmware me also didn't get frequent dc issue
and when using 1.01 firmware can't enable ipv6 config also
asellus
post Oct 18 2013, 06:55 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(rizvanrp @ Oct 18 2013, 04:39 PM)
Mikrotik Unifi PPPoE IPV6 configuration (tested on RB750 ROS 5.17 + BSRBRF01)

Prerequisites :

i. IPV6 RouterOS modules loaded in System -> Packages (Winbox)
ii. PPPoE Client profile (default) must have IPV6 set to Yes n PPP -> Profiles -> 'default' -> Protocols (Use IPv6 = Yes)

1. Replace "ether1_vlan500_UNIFI" with the name of your Unifi PPPoE client interface :

In terminal :

CODE
/ipv6 dhcp-client add interface="ether1_vlan500_UNIFI" pool-name="pppoev6" disabled=no


2. Terminal on my RouterOS says the commands for IPv6 addressing are invalid .. so use Winbox GUI and go into :

CODE
IPv6 -> Addresses

Add a new IPv6 address :

Address = ::/64
From Pool = pppoev6
Interface = ether2-local-master (replace with your LAN switch master port)
EUI64 = No
Advertise = Yes


3. Disable and enable your PPPoE client interface. It should get a new DHCPv6 prefix which will propagate to your IPv6 address list and LAN clients.

CODE
/interface pppoe-client disable ether1_vlan500_UNIFI; /interface pppoe-client enable ether1_vlan500_UNIFI

...

Reconnect your LAN clients and it should auto negotiate an IPv6 address for them.

** Do not set static /64 prefixes, they appear to be dynamic and unique to your PPPoE session ID and will change upon reconnect.
Firewall Configuration :

TCP MSS Fix :

Mangle rules so sites like Cloudflare will load. Clamps MSS to -20 bytes under IPv4 default which is 1440 (to match the difference between IPv4 and IPv6 header sizes).

CODE
/ipv6 firewall mangle add action=change-mss chain=forward disabled=no in-interface=ether1_vlan500_UNIFI new-mss=1420 passthrough=yes protocol=tcp tcp-flags=syn tcp-mss=1421-65535
/ipv6 firewall mangle add action=change-mss chain=forward disabled=no new-mss=1420 out-interface=ether1_vlan500_UNIFI passthrough=yes protocol=tcp tcp-flags=syn tcp-mss=1421-65535


Security :

Enabling the IPv6 stack means no NAT to protect you and no firewall rules (by default) to prevent someone from hitting your Mikrotik login at ::0 or your devices behind the router. Setup these firewall rules to protect your network.

Replace "ether1_vlan500_UNIFI" with the name of your Unifi PPPoE client interface :

CODE
/ipv6 firewall filter add action=accept chain=input connection-state=established disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=forward connection-state=established disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=input connection-state=related disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=forward connection-state=related disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=accept chain=input disabled=no dst-port=546 in-interface=ether1_vlan500_UNIFI protocol=udp src-address=fe80::/16
/ipv6 firewall filter add action=drop chain=input disabled=no in-interface=ether1_vlan500_UNIFI
/ipv6 firewall filter add action=drop chain=forward disabled=no in-interface=ether1_vlan500_UNIFI

** input chain rules affect traffic heading to ::0 (your router's public IPv6), forward chain rules affect traffic from your clients behind the router

** Updated firewall rules to whitelist DHCPv6 packets
*
Several questions about this:-

1. Did you manage to make the routerOS dialer gets its own /64 prefix? If yes, how did you do it? All I can do is to get a link-local address assigned to the PPPoE interface by TM.

2. For the MSS clamping command, is the command that wkKaY mentioned here works much better? But at least I know now that the minimum I have to go down is 1420. Tried 1432 before and it doesn't work.

3. Have you encountered a bug where, if you recycle your PPPoE connection, which will result of routerOS being reassigned a new /64 prefix, all computers in the network will lose its IPv6 connectivity unless the computers' interface are turned off and on again?
rizvanrp
post Oct 18 2013, 09:41 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(asellus @ Oct 18 2013, 06:55 PM)
Several questions about this:-

1. Did you manage to make the routerOS dialer gets its own /64 prefix? If yes, how did you do it? All I can do is to get a link-local address assigned to the PPPoE interface by TM.

2. For the MSS clamping command, is the command that wkKaY mentioned here works much better? But at least I know now that the minimum I have to go down is 1420. Tried 1432 before and it doesn't work.

3. Have you encountered a bug where, if you recycle your PPPoE connection, which will result of routerOS being reassigned a new /64 prefix, all computers in the network will lose its IPv6 connectivity unless the computers' interface are turned off and on again?
*
1. Nope, it's getting a link local address then negotiating DHCPv6 over that via its DHCPv6 client. I've only seen the rp-pppoe client manage to negotiate a public IPv6 prefix using ICMPv6 RA's .. that's the client being used in TM's routers anyway. I think Mikrotik is using a modified older version of rp-pppoe or proprietary client.

2. For that MSS clamping command, I simply duplicated the mangle rules created by Mikrotiks default PPP profile (Change TCP MSS - yes) and reduced the MSS size by 20 bytes. I was seeing IPv4 headers at 20 bytes and IPv6 headers at 40 bytes .. so I figured reducing the MSS clamping rule by that difference would be enough to accommodate the larger IPv6 header size.

iptables man page also seems to assume a 20 byte MSS difference :

QUOTE
--clamp-mss-to-pmtu
    Automatically clamp MSS value to (path_MTU - 40 for IPv4; -60 for IPv6). This may not function as desired where asymmetric routes with differing path MTU exist --- the kernel uses the path MTU which it would use to send packets from itself to the source and destination IP addresses. Prior to Linux 2.6.25, only the path MTU to the destination IP address was considered by this option; subsequent kernels also consider the path MTU to the source IP address.

I'm not sure why you would need to clamp to PMTU specifically as path MTU discovery in IPv6 doesn't operate the same way as it does in IPv4 and assumes the MTU is that of the link layer interface.

3. There seem to be a few bugs in Mikrotik's IPv6 implementation. I noted a GUI/terminal bug in my guide where I wasn't able to use the exported configuration from the Winbox GUI on the terminal. The router had no issues updating its IPv6 address list upon disabling/enabling the PPPoE client interface however I'm not sure how it would behave if the session hung or was disconnected administratively at the BRAS. Router reboots also seem to cause some instability with its ability to obtain a DHCPv6 lease and distribute the /64 to LAN clients. And yeah, I had to constantly bring the client interfaces down and up in order to get it to update the prefixes.

When I was testing it back at the lab in TM, accounts were assigned static /64 prefixes and I did not need to test DHCPv6 as the rp-pppoe client was able to obtain the prefix by itself. I think it should be possible to script the Mikrotik to rectify these issues though.

TSwKkaY
post Oct 18 2013, 09:56 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(rizvanrp @ Oct 18 2013, 09:41 PM)
I've only seen the rp-pppoe client manage to negotiate a public IPv6 prefix using ICMPv6 RA's .. that's the client being used in TM's routers anyway. I think Mikrotik is using a modified older version of rp-pppoe or proprietary client.
*
I'm fairly sure that it is Linux, not rp-pppoe, which does that. If you disable the autoconf sysctl, you will not see any ICMPv6 route solicitations sent.
rizvanrp
post Oct 18 2013, 10:01 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(wKkaY @ Oct 18 2013, 09:56 PM)
I'm fairly sure that it is Linux, not rp-pppoe, which does that. If you disable the autoconf sysctl, you will not see any ICMPv6 route solicitations sent.
*
Oh okay. I had to set 4 additional commands inside the rp-pppoe config to get it to obtain an IPv6 address so I assumed it was rp-pppoe tongue.gif

** My bad, it was pppd's config

This post has been edited by rizvanrp: Oct 18 2013, 10:03 PM
TSwKkaY
post Oct 18 2013, 10:15 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(rizvanrp @ Oct 18 2013, 09:41 PM)
I'm not sure why you would need to clamp to PMTU specifically as path MTU discovery in IPv6 doesn't operate the same way as it does in IPv4 and assumes the MTU is that of the link layer interface.
*
Well in the case of PPPoE, the MTU of the host's link layer is bigger than the router's.

AFAIK there's two ways to handle this - 1) through RA announcements about the smaller MTU (not sure whether this is honored by popular OSes), or 2) MSS clamping (which breaks end-to-end principle). The fallback is PMTU discovery.
iXora.ix
post Oct 19 2013, 09:49 AM

scoot scoot
******
Senior Member
1,682 posts

Joined: Jan 2007
From: Kuala Lumpur



I have RN-n16, with latest firmware. I cant get the ipv6 connection.
Did I configure it wrong?
JohnLai
post Oct 19 2013, 10:05 AM

Skeptical Cat
*******
Senior Member
3,669 posts

Joined: Apr 2006
Weird, the guideline of enabling IPV6 from the first post mentioned D-Link DIR 615 (I assumed the guideline has typo DOR615? Screenshot mentioned otherwise).

But there is no "Enable Ipv6" checkbox for my friend particular model.
He is using DIR-615 H/W Version G2 with firmware 7.09 and I can't find any IPV6 option.
asellus
post Oct 19 2013, 11:16 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(rizvanrp @ Oct 18 2013, 09:41 PM)

3. There seem to be a few bugs in Mikrotik's IPv6 implementation. I noted a GUI/terminal bug in my guide where I wasn't able to use the exported configuration from the Winbox GUI on the terminal. The router had no issues updating its IPv6 address list upon disabling/enabling the PPPoE client interface however I'm not sure how it would behave if the session hung or was disconnected administratively at the BRAS. Router reboots also seem to cause some instability with its ability to obtain a DHCPv6 lease and distribute the /64 to LAN clients. And yeah, I had to constantly bring the client interfaces down and up in order to get it to update the prefixes.

When I was testing it back at the lab in TM, accounts were assigned static /64 prefixes and I did not need to test DHCPv6 as the rp-pppoe client was able to obtain the prefix by itself. I think it should be possible to script the Mikrotik to rectify these issues though.
*
The highlighted part is what annoyed me to date with this router. Never encountered the problem before with the HE tunnel maybe because HE gives out static /64 and /48. Do you know how to script this so that there is no need to recycle the Ethernet/wireless interfaces in the computers/tablets in the network when a /64 has been assigned?

My new TP-Link TL-WR1043ND with OpenWRT that I have prepared for my other Streamyx 1Mb account doesn't suffer from that problem.
rizvanrp
post Oct 19 2013, 12:55 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(wKkaY @ Oct 18 2013, 10:15 PM)
Well in the case of PPPoE, the MTU of the host's link layer is bigger than the router's.

AFAIK there's two ways to handle this - 1) through RA announcements about the smaller MTU (not sure whether this is honored by popular OSes), or 2) MSS clamping (which breaks end-to-end principle). The fallback is PMTU discovery.
*
Setting a smaller MTU in the RA's seems the possible using the IPv6 -> ND option in RouterOS

QUOTE(asellus @ Oct 19 2013, 11:16 AM)
The highlighted part is what annoyed me to date with this router. Never encountered the problem before with the HE tunnel maybe because HE gives out static /64 and /48. Do you know how to script this so that there is no need to recycle the Ethernet/wireless interfaces in the computers/tablets in the network when a /64 has been assigned?

My new TP-Link TL-WR1043ND with OpenWRT that I have prepared for my other Streamyx 1Mb account doesn't suffer from that problem.
*
I just tested using both my Windows/Linux boxes.

i. Manually changing the IPv6 address in ROS or disabling/enabling the PPPoE client (sending a PPPoE terminate request and obtaining a new /64 prefix), the Mikrotik sends out an RA and the clients will have the previous + current /64's bound
ii. A BRAS session reset from the headend results in the same behavior from the client .. so hung sessions or administrative disconnects shouldn't be a problem

My Linux client doesn't seem to be unaffected when having multiple /64 prefixes on the interface. Refreshing the client interface may only be needed if you want to purge the older invalid prefixes but it doesn't seem to affect the ability for the clients to utilize IPv6 as long as one of the prefixes is valid. I've tried getting the Routerboard to force the clients to drop the older prefix but nothing seems to work so far.

Interestingly, during one of the server side session terminates I requested.. I was reassigned the same IPv4 address but my IPv6 prefix was incremented by 1.. so it seems the IPv6 prefix isn't being derived from the IPv4 value but rather the session identifier itself.
asellus
post Oct 19 2013, 02:12 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(rizvanrp @ Oct 19 2013, 12:55 PM)

i. Manually changing the IPv6 address in ROS or disabling/enabling the PPPoE client (sending a PPPoE terminate request and obtaining a new /64 prefix), the Mikrotik sends out an RA and the clients will have the previous + current /64's bound
ii. A BRAS session reset from the headend results in the same behavior from the client .. so hung sessions or administrative disconnects shouldn't be a problem

My Linux client doesn't seem to be unaffected when having multiple /64 prefixes on the interface. Refreshing the client interface may only be needed if you want to purge the older invalid prefixes but it doesn't seem to affect the ability for the clients to utilize IPv6 as long as one of the prefixes is valid. I've tried getting the Routerboard to force the clients to drop the older prefix but nothing seems to work so far.

Interestingly, during one of the server side session terminates I requested.. I was reassigned the same IPv4 address but my IPv6 prefix was incremented by 1.. so it seems the IPv6 prefix isn't being derived from the IPv4 value but rather the session identifier itself.
*
My experience when using the HE tunnel shows that multiple /64 on client interfaces should not pose any problems. Only that with TM IPv6, I started to have this problem.

Getting the same IPv4 address when recycling the PPPoE connection seems to be common in the pas year or so, that's why I wait for 10 seconds or so between disabling and re-enabling the PPPoE connection.
asellus
post Oct 19 2013, 02:28 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


I think I found out what the problem is:-

Before I recycle the PPPoE connection:-
Attached Image

After I recycle the PPPoE connection:-
Attached Image

This really isn't supposed to happen. The older prefixes are not depreciated.
Moogle Stiltzkin
post Oct 19 2013, 09:00 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:31 AM
vincent_ng86
post Oct 20 2013, 11:54 AM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


Hmm, changing the MTU to 1392 in IPv6 seems to done the trick. No problem accessing facebook now.

This post has been edited by vincent_ng86: Oct 20 2013, 12:10 PM
vincent_ng86
post Oct 20 2013, 12:17 PM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


Hmm, how come I don't have the IPv6 tag on my replies although I have gone through the test at http://ipv6test.google.com confirming the availability.
asellus
post Oct 20 2013, 01:14 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(vincent_ng86 @ Oct 20 2013, 12:17 PM)
Hmm, how come I don't have the IPv6 tag on my replies although I have gone through the test at http://ipv6test.google.com confirming the availability.
*
If you use Firefox, then you just have encountered its bug, like I do now.
GothFebrio
post Oct 20 2013, 03:09 PM

too long...did not read
******
Senior Member
1,304 posts

Joined: Jan 2009
From: Kuala Lumpur


Just noticed this thread, turned on ipv6 on my router(asus rt n66u) and it works just fine.
vincent_ng86
post Oct 20 2013, 05:57 PM

Regular
******
Senior Member
1,659 posts

Joined: Feb 2005


QUOTE(asellus @ Oct 20 2013, 01:14 PM)
If you use Firefox, then you just have encountered its bug, like I do now.
*
Am using Safari on both iOS and OSX. Wondering why.
prasys
post Oct 20 2013, 08:42 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
Firefox seems to prefer IPV4 over IPV6 for some weird reasons

Got it working on my NT-56U. I was using HE.net , finally it is good to have native IPV6 support smile.gif
Moogle Stiltzkin
post Oct 20 2013, 08:45 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:35 AM
asellus
post Oct 20 2013, 10:22 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


I think the IPv6 connectivity to forum.lowyat.net is down ATM.

QUOTE(Moogle Stiltzkin @ Oct 20 2013, 08:45 PM)
any chance you will be posting a guide on your athena unifi site with screenshots ? Bit confused on some parts.

Like....the TCP MSS fix, where do you add this code ?

Also you mentioneddo not set static /64 prefix. I don't understand where in the settings you are referring to. If it's the router part (not on the microtik), well i use a tomato router, but i'm clueless what option to select under the enable ipv6 option since there are a few different modes X_X;
*
The TCP MSS fix is applied on '/ipv6 firewall mangle' section. No need to set a static /64 prefix in '/ipv6 address' section either, unlike when you use a HE.net tunnel, because the allocated prefix from TM is dynamic.


Moogle Stiltzkin
post Oct 20 2013, 10:30 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:35 AM
asellus
post Oct 20 2013, 10:34 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Moogle Stiltzkin @ Oct 20 2013, 10:30 PM)
thx.

well maybe i'll attempt it doh.gif but save my configuration first just in case.

But in the tomato router what option under enable ipv6 should select ?  hmm.gif
*
In the picture below?

» Click to show Spoiler - click again to hide... «


Try DHCPv6 with Prefix Delegation.
Moogle Stiltzkin
post Oct 21 2013, 02:38 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:36 AM
TSwKkaY
post Oct 21 2013, 05:11 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Coincidentally, after some downtime on my FTTH link today, at reconnection my BRAS now assigns me an allocation through DHCPv6 thumbup.gif
TSwKkaY
post Oct 21 2013, 05:15 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Our hosting provider's IPv6 is down, so you guys won't be able to surf the forum over IPv6 until it is rectified.
Alpha Wolf
post Oct 21 2013, 05:33 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 02:38 AM)
Yep  nod.gif

so i leave the static dns field blank ? prefix length 64 default. Accept RA from WAN but NOT lan (default) ?
i tried accessing my rb250gs switch but i forgot the username password. admin/blank doesn't work :/ so i may need to reset the switch and start over.

But rivzan's guide on his website is offline, so i can't do it right now  cry.gif is he going to restore the site anytime soon  ohmy.gif
*
You can choose to use google's ipv6 dns. Prefix length is 64, yes. Accept RA from WAN only unless this isn't your primary router connecting to the internet.

You could always use wayback machine - http://archive.org/web/ a copy of that site when it was up.
TSwKkaY
post Oct 21 2013, 06:27 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
I've been investigating the MTU issue more closely now that I have IPv6 working at home.

I think it's a problem specific to Mikrotik. MTU for the PPPoE interface is set to 1480 by default. So if you use clamp values that you found through googling, they might not work if calculated to assume an MTU of 1492.

Further compounding the problem, it appears that a ICMPv6 Packet Too Big isn't sent back to the host in this case.

In my opinion, the best solution on the Mikrotik is to set your IPv6 -> ND -> MTU advertisment to match your PPPoE interface MTU. Doing it this way is less hackish than writing mangle rules for the router to change the TCP MSS. Furthermore the MTU hint will be usable by protocols other than TCP.
Moogle Stiltzkin
post Oct 21 2013, 06:31 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:36 AM
Alpha Wolf
post Oct 21 2013, 06:50 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(wKkaY @ Oct 21 2013, 06:27 AM)
I've been investigating the MTU issue more closely now that I have IPv6 working at home.

I think it's a problem specific to Mikrotik. MTU for the PPPoE interface is set to 1480 by default. So if you use clamp values that you found through googling, they might not work if calculated to assume an MTU of 1492.

Further compounding the problem, it appears that a ICMPv6 Packet Too Big isn't sent back to the host in this case.

In my opinion, the best solution on the Mikrotik is to set your IPv6 -> ND -> MTU advertisment to match your PPPoE interface MTU. Doing it this way is less hackish than writing mangle rules for the router to change  the TCP MSS. Furthermore the MTU hint will be usable by protocols other than TCP.
*
Yes, I wanted to suggest the same as it is more efficient. I've tried matching the MTU advertisement to the pppoe line's MTU (in my case 1492) and it works. I wonder what about the 60 bytes overhead deduction that the linked blog on MSS suggested. 1492 works fine for me. Clamping MSS is a work-around and technically not the solution. As a fail-safe approach, start setting your MTU advertisement to the min value of 1280 and slowly increase from there.

A more conclusive way to test whether your MTU setting works is to use the "Other IPv6 Sites" tab on http://test-ipv6.com/ after successfully running the initial test. This should properly test your MTU against many different servers located all around the world using IPv6. Don't be alarm if you get a grey-bluish dot, as some servers might be down occasionally but you should be getting green ticks otherwise:
» Click to show Spoiler - click again to hide... «



By the way, when will lowyat.net's IPv6 connection be up? I am starting to miss those IPv6 tags already.

QUOTE(Moogle Stiltzkin @ Oct 21 2013, 06:31 AM)
primary router..... so are you saying for my network setup

fiberhome modem > Microtik RB250GS switch > Linksys E4200 V1 router
So i need to Wan RA only for the microtik, but for the linksys, RA enable for both WAN and LAN ? is that what you meant  hmm.gif
today they were doing maintenance in the area, i suspect to do with IPV6 but what they changing exactly i'm not sure  hmm.gif
But is that recommended? Like i noticed some sites is blocked by the isp dns. But when use googledns or opendns can access them.

But problem is if use google or opendns
1. higher latency for games
2. harder to use the local akamai cache servers, so may result in exceeding my monthly bandwidth quotas.
*
Your primary router is the device that performs the pppoe connection through your modem. Is that Microtik switch performing the internet connection? Not familiar with that Microtik device as it sounds like just a switch? Anyway, if your Linksys connects to your Microtik via Linksys's WAN port, then yes.

True, it does depend on the websites you use. I personally find google dns much faster compared to open dns. If you want to give priority to local servers, use TM for primary dns and google for secondary dns.

QUOTE(JohnLai @ Oct 19 2013, 10:05 AM)
Weird, the guideline of enabling IPV6 from the first post mentioned D-Link DIR 615 (I assumed the guideline has typo DOR615? Screenshot mentioned otherwise).

But there is no "Enable Ipv6" checkbox for my friend particular model.
He is using DIR-615 H/W Version G2 with firmware 7.09 and I can't find any IPV6 option.
*
It is indeed a typo. Key "i" and "o" are next to each other on the keyboard. I guess the person who put together that ipv6 guide was pressed for time.

You need to update your firmware.

This post has been edited by Alpha Wolf: Oct 21 2013, 07:34 AM


Attached thumbnail(s)
Attached Image
Moogle Stiltzkin
post Oct 21 2013, 06:59 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:36 AM
Alpha Wolf
post Oct 21 2013, 07:10 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 06:59 AM)
I can't login to my rb250gs have to reset, but rivzan's website seems down so i can't remember the guide to set up again, so i'm stuck X_X:

also been a long time since i did it, so i'm not sure about this. But i usually enter my internet info in my router, so maybe the dial up is performed there ? Whereas only the vlan tagging is done via the rb250gs.
Does anyone have a cache for this page ?
http://unifi.athena.my/mikrotik_rb250gs.php
*
Like I've mentioned, use wayback machine. Latest snapshot January 2013. I thought his site was down far back than this?
http://web.archive.org/web/20130118122637/...tik_rb250gs.php

Looks like it's just a switch indeed. Dial up is performed by your modem. Which modem are you using?

This post has been edited by Alpha Wolf: Oct 21 2013, 07:12 AM
Moogle Stiltzkin
post Oct 21 2013, 07:11 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:37 AM
Alpha Wolf
post Oct 21 2013, 07:43 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 18 2013, 06:14 PM)
no idea
so far now didn't facing frequent dc issue on 1.06 firmware with disable ipv6
yet, by the time I using 1.01 firmware me also didn't get frequent dc issue
and when using 1.01 firmware can't enable ipv6 config also
*
Yeah, for some reason dual wan cannot be enabled in fw 1.01.
asellus
post Oct 21 2013, 08:03 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Oct 21 2013, 06:27 AM)
I've been investigating the MTU issue more closely now that I have IPv6 working at home.

I think it's a problem specific to Mikrotik. MTU for the PPPoE interface is set to 1480 by default. So if you use clamp values that you found through googling, they might not work if calculated to assume an MTU of 1492.

Further compounding the problem, it appears that a ICMPv6 Packet Too Big isn't sent back to the host in this case.

In my opinion, the best solution on the Mikrotik is to set your IPv6 -> ND -> MTU advertisment to match your PPPoE interface MTU. Doing it this way is less hackish than writing mangle rules for the router to change  the TCP MSS. Furthermore the MTU hint will be usable by protocols other than TCP.
*
Did you also see the bug I mentioned in point no.3 I mentioned here?

BTW, setting the MTU in ND do work.
XeactorZ
post Oct 21 2013, 10:45 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 21 2013, 07:43 AM)
Yeah, for some reason dual wan cannot be enabled in fw 1.01.
*
any idea how to downgrade to 1.01 firmware ?
rizvanrp
post Oct 21 2013, 01:43 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(wKkaY @ Oct 21 2013, 06:27 AM)
I've been investigating the MTU issue more closely now that I have IPv6 working at home.

I think it's a problem specific to Mikrotik. MTU for the PPPoE interface is set to 1480 by default. So if you use clamp values that you found through googling, they might not work if calculated to assume an MTU of 1492.

Further compounding the problem, it appears that a ICMPv6 Packet Too Big isn't sent back to the host in this case.

In my opinion, the best solution on the Mikrotik is to set your IPv6 -> ND -> MTU advertisment to match your PPPoE interface MTU. Doing it this way is less hackish than writing mangle rules for the router to change  the TCP MSS. Furthermore the MTU hint will be usable by protocols other than TCP.
*
Agreed, the mangle rules have an additional disadvantage of using more resources on the router. Setting the MTU flag in the RAs seems to work biggrin.gif

My only remaining issue is getting rid of the expired v6 prefixes once the session is killed. My home server interface currently looks like this.. :

CODE
         inet6 addr: 2001:e68:5420:15bf:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bd:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bc:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bb:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15ba:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15b9:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15b8:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1590:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1585:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1583:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: fe80::16da:e9ff:fe98:e847/64 Scope:Link
         inet6 addr: 2001:e68:5420:1583:46:f4ff:fe2c:93f0/64 Scope:Global
         inet6 addr: 2001:e68:5420:1581:46:f4ff:fe2c:93f0/64 Scope:Global

zhuoyang
post Oct 21 2013, 02:19 PM

Getting Started
**
Junior Member
197 posts

Joined: Jul 2011
how to enable IPv6 on Unifi DIR-615 with DD-WRT firmware?
Alpha Wolf
post Oct 21 2013, 06:43 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 21 2013, 10:45 AM)
any idea how to downgrade to 1.01 firmware ?
*
You need to get a copy of the 1.01 firmware first, where DellMalaysia has requested through an email awaiting reply from TM. This is also the reason why I am in search for that firmware.


QUOTE(rizvanrp @ Oct 21 2013, 01:43 PM)
Agreed, the mangle rules have an additional disadvantage of using more resources on the router. Setting the MTU flag in the RAs seems to work biggrin.gif

My only remaining issue is getting rid of the expired v6 prefixes once the session is killed. My home server interface currently looks like this.. :

CODE
         inet6 addr: 2001:e68:5420:15bf:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bd:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bc:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15bb:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15ba:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15b9:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:15b8:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1590:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1585:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: 2001:e68:5420:1583:16da:e9ff:fe98:e847/64 Scope:Global
         inet6 addr: fe80::16da:e9ff:fe98:e847/64 Scope:Link
         inet6 addr: 2001:e68:5420:1583:46:f4ff:fe2c:93f0/64 Scope:Global
         inet6 addr: 2001:e68:5420:1581:46:f4ff:fe2c:93f0/64 Scope:Global

*
I was having the same issue with RA clients preferring the older prefixes over the newer ones, thus accumulating a long list of v6 addresses. For wireless devices, his can be fixed by disconnecting and reconnecting to the network. But this can be troublesome. The solution is to shorten the lifetime these prefixes remained preferred in the RA deamon. Most ISP provide static prefixes as v6 prefixes are meant to be static in general, hence why RA deamons have it set to 1 day or more. For some reason, TM is handing out dynamic prefixes. If your router uses radvd like mine for RAs, you can configure this in the config file within the prefix section:
QUOTE
# Shorter lifetimes 1 day valid and 2 hour preferred
                AdvValidLifetime 86400;
                AdvPreferredLifetime 7200;

Otherwise, look for settings related to the time advertised prefixes remain valid.


QUOTE(zhuoyang @ Oct 21 2013, 02:19 PM)
how to enable IPv6 on Unifi DIR-615 with DD-WRT firmware?
*
Just when I was about to wonder if anyone else was using DD-WRT with IPv6... I guess technically none yet?

Incidentally, I've spent the last few days relentlessly sorting out and getting IPv6 connection working with DD-WRT. It was an IPv6 learning experience for me too as I was completely new to IPv6. I finally have my Asus RT-N66U running on DD-WRT fully working with Unifi's native IPv6 along side 500 and 600 vlan tagging. icon_rolleyes.gif

Currently DD-WRT has less support for IPv6 compared to other custom firmwares like Tomato and OpenWRT, at least this is according to the web interface of DD-WRT, most of which needs to be manually configure using the command line interface and script files. But being well accustomed to DD-WRT and its extensive features, I wanted this to work. Only the big builds have IPv6 modules included, but with optware and ipkg and lots of patience, it's fully possible.

In short, here are the applications I am using:
1) rdisc6 to get ICMPv6 from ISP for the WAN interface.
2) DHCPv6 client to get v6 prefix from ISP.
3) and finally radvd to advertise that obtained prefix out to clients.

I also added and configured ip6tables for the v6 firewall.

Here are more details on my setup. Note this is a custom web interface page I included using the MyPage feature of DD-WRT for debugging and status purposes. So far it's been running really stable. No point in masking my IP addresses since they are dynamic plus I run a server. biggrin.gif
» Click to show Spoiler - click again to hide... «


This post has been edited by Alpha Wolf: Oct 21 2013, 08:17 PM


Attached thumbnail(s)
Attached Image
Moogle Stiltzkin
post Oct 21 2013, 07:11 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:37 AM
rizvanrp
post Oct 21 2013, 07:16 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(Alpha Wolf @ Oct 21 2013, 06:43 PM)
I was having the same issue with RA clients preferring the older prefixes over the newer ones, thus accumulating a long list of v6 addresses. For wireless devices, his can be fixed by disconnecting and reconnecting to the network. But this can be troublesome. The solution is to shorten the lifetime these prefixes remained preferred in the RA deamon. Most ISP provide static prefixes as v6 prefixes are meant to be static in general, hence why RA deamons have it set to 1 day or more. For some reason, TM is handing out dynamic prefixes. If your router uses radvd like mine for RAs, you can configure this in the config file within the prefix section:

Otherwise, look for settings related to the time advertised prefixes remain valid.
Adjustable in IPv6 -> ND -> Prefixes -> Default for RouterOS

No Unifi at my site so maybe someone else with a Mikrotik can test if it works
Eoma
post Oct 21 2013, 07:29 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


On Windows (vista/7) a quick disable and enable on the ethernet adapter gets rid of the old prefix.

This post has been edited by Eoma: Oct 21 2013, 07:29 PM
Moogle Stiltzkin
post Oct 21 2013, 07:33 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:37 AM
Eoma
post Oct 21 2013, 07:46 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


Not for the first time, if you redial, it seems the old prefix is not removed.
I initially thought it was due to the half baked TP Link firmware, but it seems others are experiencing the same thing too.
TSwKkaY
post Oct 21 2013, 08:04 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(rizvanrp @ Oct 21 2013, 07:16 PM)
Adjustable in IPv6 -> ND -> Prefixes -> Default for RouterOS

No Unifi at my site so maybe someone else with a Mikrotik can test if it works
*
I have set lowered it from 30d/1w to 2h/1h for Valid/Preferred. Confirmed on Linux that the new lifetimes have taken effect.
TSwKkaY
post Oct 21 2013, 08:08 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(Alpha Wolf @ Oct 21 2013, 06:43 PM)
If your router uses radvd like mine for RAs, you can configure this in the config file within the prefix section:
QUOTE
# Very short lifetimes for dynamic addresses
                AdvValidLifetime 300;
                AdvPreferredLifetime 120;

*
In RFC 4862 section 5.5.3, it is recommended that hosts ignore AdvValidLifetime < 2 hours, to avoid a denial of service attack from bogus advertisements. So I think you should raise that to 2 hours.
Alpha Wolf
post Oct 21 2013, 08:10 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(wKkaY @ Oct 21 2013, 08:08 PM)
In RFC 4862 section 5.5.3, it is recommended that hosts ignore AdvValidLifetime < 2 hours, to avoid a denial of service attack from bogus advertisements. So I think you should raise that to 2 hours.
*
Good point, I read about that too. I will have it adjusted. The default settings for radvd is 1 day valid and 4 hours preferred.

This post has been edited by Alpha Wolf: Oct 21 2013, 08:18 PM
asellus
post Oct 21 2013, 08:17 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


Old prefixes not being removed isn't really a problem. The problem lies in the fact that old prefixes not being marked as depreciated when it should have been.
Alpha Wolf
post Oct 21 2013, 08:30 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 07:33 PM)
does all new ipv6 have to do this for first time setup ? Or is this something have to do on a regular basis after router reboot  hmm.gif
*
Honestly, if I did not reconnect to TM with my router so frequently during my debugging phase, this issue would have been non-existent for me. In fact, I could have left them at the default settings because I leave my router running 24/7 and my pppoe connection is rock solid. This setup is only required if you get very frequent disconnects on your pppoe connection and it auto reconnects within less than the preferred lifetime setting.
Moogle Stiltzkin
post Oct 21 2013, 08:32 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:37 AM
Alpha Wolf
post Oct 21 2013, 08:38 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 08:32 PM)
what is causing this ? Whos fault is it ? Unifis implementation, or the router firmware which lack support ?
Same situation here. 24/7, but when i debug, i reboot my router after update or changes, so this could add up and start to be annoying for me too  shakehead.gif
*
It's not really a "fault". But if I were to blame something, it's the dynamic prefixes that TM hands out.

If you reboot your router that connects to your client devices, the prefixes would automatically clear themselves, just like how disconnecting and reconnecting the ethernet interface on the client devices solves the problem. Rebooting your router is analogous to disconnecting and reconnecting to your client devices. So I really don't see any issues in this at all.

I have a an access point connected to my router which my wireless laptop still connects to when I reboot my router, hence the old prefixes aren't cleared.

Edit: haha, noticed that you edited to add that picture

This post has been edited by Alpha Wolf: Oct 21 2013, 08:41 PM
TSwKkaY
post Oct 21 2013, 08:39 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 21 2013, 08:17 PM)
Old prefixes not being removed isn't really a problem. The problem lies in the fact that old prefixes not being marked as depreciated when it should have been.
*
Ahh yeah Windows has that problem. I did some reading and found one way to address it: the routers sends a 0-second ValidLifetime RA to "clear" the prefix. This probably isn't supported by Mikrotik though.
Alpha Wolf
post Oct 21 2013, 08:44 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(wKkaY @ Oct 21 2013, 08:39 PM)
Ahh yeah Windows has that problem. I did some reading and found one way to address it: the routers sends a 0-second ValidLifetime RA to "clear" the prefix. This probably isn't supported by Mikrotik though.
*
Interesting approach but I wonder if it works. This could be scripted in DD-WRT - launch radvd with a separate config file with 0 ValidLifeTime then kill radvd and launch it again with the primary config file.
Moogle Stiltzkin
post Oct 21 2013, 08:47 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:40 AM
rizvanrp
post Oct 21 2013, 08:47 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(wKkaY @ Oct 21 2013, 08:39 PM)
Ahh yeah Windows has that problem. I did some reading and found one way to address it: the routers sends a 0-second ValidLifetime RA to "clear" the prefix. This probably isn't supported by Mikrotik though.
*
user posted image
RA is sent immediately after configuration is applied, should be able to script this right?

CODE
/ipv6 nd prefix add autonomous=yes disabled=no interface=ether2-master-local on-link=yes preferred-lifetime=0s prefix=2001:e68:dead:beef::/64 valid-lifetime=0s


This post has been edited by rizvanrp: Oct 21 2013, 08:47 PM
TSwKkaY
post Oct 21 2013, 08:57 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(rizvanrp @ Oct 21 2013, 08:47 PM)
RA is sent immediately after configuration is applied, should be able to script this right?
CODE
/ipv6 nd prefix add autonomous=yes disabled=no interface=ether2-master-local on-link=yes preferred-lifetime=0s prefix=2001:e68:dead:beef::/64 valid-lifetime=0s

*
Hmm you might be on to something!

Mikrotik wiki has a code snippet that can be used together with that: http://wiki.mikrotik.com/wiki/Manual:Scrip...ce_have_changed
Alpha Wolf
post Oct 21 2013, 09:06 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 07:11 PM)
Okay i can't test ipv6 i found out.

So just wondering, does anyone with a tomato router who managed to get ipv6 to work yet ? Interested to know doh.gif
@alpha -

thx for confirming unifi ipv6 works on dd-wrt. i'm sure others will appreciate a pictorial guide to set that up  nod.gif
*
The web interface for configuring ipv6 on Tomato looks very promising as they have options for native ipv6. I am sure it's possible.

hmm.gif I'm considering where to place such a guide because it is going to be long and it pre-requires enabling jffs for installing additional applications or using optware and most importantly, running startup scripts to automate the process every time it boots up. Depending on the version of dd-wrt, additional ipv6 modules need to be downloaded and loaded onto dd-wrt separately.

As for my setup, the only thing I'm wondering about right now is: Why do I get two different v6 prefixes for my WAN and LAN? Shouldn't they be the same? Also, I can reach my router from the external internet by using both my WAN or LAN v6 IP.

This post has been edited by Alpha Wolf: Oct 21 2013, 09:16 PM
Moogle Stiltzkin
post Oct 21 2013, 09:16 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:40 AM
Alpha Wolf
post Oct 21 2013, 09:21 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 09:16 PM)
that sounds.... complicated  shocking.gif

*
Yes sweat.gif , but this could all be easily scripted. You only need to get the right modules and application for your version of dd-wrt, particularly if you're using a different Linux kernel version. I am using the latest K3.X.

On a side note, I had to modify and compile a switch driver to enable support for vlanids above 15, namely 500 and 600 that Unifi uses, for my Broadcom based router running linux kernel 3.10. This enables me to directly connect my dd-wrt router to the fiber modem. One less device to run 24/7 and no more requiring the use of that TM router as a bridge for internet, plus my IPTV still works when I need it.

I could now use that L7 TM router for testing. Doubt it will work but maybe I could try flashing it with dd-wrt.

This post has been edited by Alpha Wolf: Oct 21 2013, 09:32 PM
rizvanrp
post Oct 21 2013, 09:35 PM

Getting Started
Group Icon
Elite
195 posts

Joined: Sep 2006



QUOTE(wKkaY @ Oct 21 2013, 08:57 PM)
Hmm you might be on to something!

Mikrotik wiki has a code snippet that can be used together with that: http://wiki.mikrotik.com/wiki/Manual:Scrip...ce_have_changed
*
Something like this maybe? biggrin.gif

CODE
:log info "IPv6 Check Start";

:local poolname "pppoev6";
:local intname "ether1-gigabit-master";

:global oldV6;
:local newV6;
:set newV6 [/ipv6 pool get $poolname prefix];

:if ([ :typeof $oldV6 ] = "nothing") do={
:set oldV6 $newV6
}

:if ($newV6 != $oldV6) do={
:log info "Mismatch -- killing old prefix";
:log info "Current -- $newV6";
:log info "Previous -- $oldV6";
:ipv6 nd prefix add autonomous=yes disabled=no interface=$intname on-link=yes preferred-lifetime=0s prefix=$oldV6 valid-lifetime=0s;
:ipv6 nd prefix remove [/ipv6 nd prefix find prefix=$oldV6];
:set oldV6 $newV6;
}

:log info "IPv6 Check Stop";

I was trying to grab the prefix directly from the interface but no luck, kept getting garbage so I ended up pulling from the DHCPv6 client pool instead sad.gif

** Updated the if check for the previous IPv6 prefix

This post has been edited by rizvanrp: Oct 21 2013, 10:17 PM
Moogle Stiltzkin
post Oct 21 2013, 10:22 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:40 AM
asellus
post Oct 21 2013, 10:25 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Moogle Stiltzkin @ Oct 21 2013, 08:32 PM)
what is causing this ? Whos fault is it ? Unifis implementation, or the router firmware which lack support ?
user posted image

*
No, it is the routerOS problem.

QUOTE(Alpha Wolf @ Oct 21 2013, 09:06 PM)

As for my setup, the only thing I'm wondering about right now is: Why do I get two different v6 prefixes for my WAN and LAN? Shouldn't they be the same? Also, I can reach my router from the external internet by using both my WAN or LAN v6 IP.
*
Because that's how it works. If your PPPoE dialer supports IPv6, it can get itself its own /64, then another /64 for clients behind the router. Not that different really than a HE.net tunnel.
zhuoyang
post Oct 21 2013, 10:30 PM

Getting Started
**
Junior Member
197 posts

Joined: Jul 2011
QUOTE(Alpha Wolf @ Oct 21 2013, 06:43 PM)
Just when I was about to wonder if anyone else was using DD-WRT with IPv6... I guess technically none yet?

Incidentally, I've spent the last few days relentlessly sorting out and getting IPv6 connection working with DD-WRT. It was an IPv6 learning experience for me too as I was completely new to IPv6. I finally have my Asus RT-N66U running on DD-WRT fully working with Unifi's native IPv6 along side 500 and 600 vlan tagging.  icon_rolleyes.gif

Currently DD-WRT has less support for IPv6 compared to other custom firmwares like Tomato and OpenWRT, at least this is according to the web interface of DD-WRT, most of which needs to be manually configure using the command line interface and script files. But being well accustomed to DD-WRT and its extensive features, I wanted this to work. Only the big builds have IPv6 modules included, but with optware and ipkg and lots of patience, it's fully possible.

In short, here are the applications I am using:
1) rdisc6 to get ICMPv6 from ISP for the WAN interface.
2) DHCPv6 client to get v6 prefix from ISP.
3) and finally radvd to advertise that obtained prefix out to clients.

I also added and configured ip6tables for the v6  firewall.

Here are more details on my setup. Note this is a custom web interface page I included using the MyPage feature of DD-WRT for debugging and status purposes. So far it's been running really stable. No point in masking my IP addresses since they are dynamic plus I run a server. biggrin.gif
» Click to show Spoiler - click again to hide... «

*
Hmm, is it possible in the DIR-615 ? the space in DIR-615 is quite limited
Alpha Wolf
post Oct 21 2013, 10:49 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(asellus @ Oct 21 2013, 10:25 PM)
Because that's how it works. If your PPPoE dialer supports IPv6, it can get itself its own /64, then another /64 for clients behind the router. Not that different really than a HE.net tunnel.
*
Oh good! So I'm not over pulling a prefix too many or anything like that. I still find it interesting how I can use both my WAN and LAN v6 IP as my public IP. It's like I'm having two public addresses. I guess IPv6 has too many addresses to offer. The way IPv6 works is almost entirely different from IPv4, apparently it's not just as simple as "adding more addresses". I've never tried tunnels as I started straight with native IPv6.

QUOTE(zhuoyang @ Oct 21 2013, 10:30 PM)
Hmm, is it possible in the DIR-615 ? the space in DIR-615 is quite limited
*
You are only required to enable JFFS support on your router to use ipkg. Then, attach a usb drive to your router and bind mount it to /jffs and poof! Your jffs has the space of your USB drive! You have to change your usb mount path accordingly.
CODE
mount --bind /mnt/sda1/jffs /jffs

XeactorZ
post Oct 22 2013, 01:04 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 21 2013, 06:43 PM)
You need to get a copy of the 1.01 firmware first, where DellMalaysia has requested through an email awaiting reply from TM. This is also the reason why I am in search for that firmware.
*
thanks for telling
1st day use the unifi after yesterday midnight reset the router, no dc issue
let see how it goes ...
hinamoriamu
post Oct 22 2013, 10:10 AM

On my way
****
Senior Member
578 posts

Joined: Jun 2012
Just one curious question
If TM never assign a public IPv4 address, will IPv6 will help them to resolve the issue for CCTV or IPCam port forwarding?
JohnLai
post Oct 22 2013, 10:22 AM

Skeptical Cat
*******
Senior Member
3,669 posts

Joined: Apr 2006
QUOTE(hinamoriamu @ Oct 22 2013, 10:10 AM)
Just one curious question
If TM never assign a public IPv4 address, will IPv6 will help them to resolve the issue for CCTV or IPCam port forwarding?
*
Technically, IPv6 could solve the issue, assuming if the router at TM side is capable of IPv6 support.
This way, you will have the private IPv4 and public IPv6 address.

Problem, how do you know if your other end of connection support IPv6 as well?
Example, location A supports both IPv4 (Private or Public) and IPv6 (Public) while location B (the one you want to access) can only support IPv4 (Private, NAT-ed). You gonna have issue setting up teredo tunneling etc just to get pseudo IPv6 working. rclxub.gif
hinamoriamu
post Oct 22 2013, 10:44 AM

On my way
****
Senior Member
578 posts

Joined: Jun 2012
QUOTE(JohnLai @ Oct 22 2013, 10:22 AM)
Technically, IPv6 could solve the issue, assuming if the router at TM side is capable of IPv6 support.
This way, you will have the private IPv4 and public IPv6 address.

Problem, how do you know if your other end of connection support IPv6 as well?
Example, location A supports both IPv4 (Private or Public) and IPv6 (Public) while location B (the one you want to access) can only support IPv4 (Private, NAT-ed). You gonna have issue setting up teredo tunneling etc just to get pseudo IPv6 working.  rclxub.gif
*
Thanks for the clarification, seems it will not resolve as most of them will access from mobile ISP that still uses IPv4 via hand phone
Alpha Wolf
post Oct 22 2013, 11:13 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(JohnLai @ Oct 22 2013, 10:22 AM)
Technically, IPv6 could solve the issue, assuming if the router at TM side is capable of IPv6 support.
This way, you will have the private IPv4 and public IPv6 address.

Problem, how do you know if your other end of connection support IPv6 as well?
Example, location A supports both IPv4 (Private or Public) and IPv6 (Public) while location B (the one you want to access) can only support IPv4 (Private, NAT-ed). You gonna have issue setting up teredo tunneling etc just to get pseudo IPv6 working.  rclxub.gif
*
Instead of going through the hassle setting up tunnels, an ipv6 proxy could be used. http://www.ipv6proxy.net/
maxiscool
post Oct 22 2013, 04:52 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Need some understanding, what happen to the device behind the router when turn on IPv6 for Unifi?

Will all be IPv6 or it is still IPv4?

Being using Mikrotik.

Alpha Wolf
post Oct 22 2013, 05:05 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(maxiscool @ Oct 22 2013, 04:52 PM)
Need some understanding, what happen to the device behind the router when turn on IPv6 for Unifi?

Will all be IPv6 or it is still IPv4?

Being using Mikrotik.
*
IPv6 and IPv4 can run concurrently so they will have both.
maxiscool
post Oct 22 2013, 05:46 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
In this case, all the device behind router will get IPv6 and IPv4 IP address.

For the IPv6 case, the IPv6 DHCP is from the router? or TM DHCP?
asellus
post Oct 22 2013, 06:36 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 22 2013, 05:46 PM)
In this case, all the device behind router will get IPv6 and IPv4 IP address.

For the IPv6 case, the IPv6 DHCP is from the router? or TM DHCP?
*
From the router. TM DHCP only hands out prefix(es), router's DHCP (or RA) hands out address(es) to client computers.

edt: BTW, routerOS does not support DHCPv6 yet (probably never), so RA is the way to go.

This post has been edited by asellus: Oct 22 2013, 06:37 PM
Alpha Wolf
post Oct 22 2013, 07:35 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(asellus @ Oct 22 2013, 06:36 PM)
From the router. TM DHCP only hands out prefix(es), router's DHCP (or RA) hands out address(es) to client computers.

edt: BTW, routerOS does not support DHCPv6 yet (probably never), so RA is the way to go.
*
Is there no way to run downloaded ipkg installations on routerOS like WRT-based OS?
asellus
post Oct 22 2013, 07:55 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Alpha Wolf @ Oct 22 2013, 07:35 PM)
Is there no way to run downloaded ipkg installations on routerOS like WRT-based OS?
*
routerOS has DHCPv6, but it only hands out prefixes, not addresses.
maxiscool
post Oct 23 2013, 07:32 AM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Trying to follow this guide to enable IPv6 on my setup. However when I run a test on the test-ipv6.com, it still doesn't show the IPv6 address.

However, on the Miktrotik Winbox, I can see the IPv6 address and also my client machine, I'm able to see the IPv6 address.

Any advise on where to start troubleshoot?

asellus
post Oct 23 2013, 09:45 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 23 2013, 07:32 AM)
Trying to follow this guide to enable IPv6 on my setup. However when I run a test on the test-ipv6.com, it still doesn't show the IPv6 address.

However, on the Miktrotik Winbox, I can see the IPv6 address and also my client machine, I'm able to see the IPv6 address.

Any advise on where to start troubleshoot?
*
Recycle your Ethernet/wireless connection first, then try again.
Kiding
post Oct 23 2013, 10:51 PM

Regular
******
Senior Member
1,134 posts

Joined: Jan 2003
From: Seri Kembangan


Finally got my TP-Link TL-WR841ND v7 with OpenWRT 12.09 IPV6 working properly after two nights of studying and troubleshooting.

Attached Image

Now my Windows, Solaris, iPad and Android phone are getting ipv6 flex.gif laugh.gif

Too bad TM not giving fixed ipv6 address sleep.gif
darrenliew96
post Oct 23 2013, 11:50 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


One shocking discovery...
I found out that youtube works better with IPv6 cdn than the IPv4 CDN.

IPv6 CDN max speed 500kbps
user posted image

IPv4 CDN max speed 50kbps
user posted image

Can anyone confirm?
Best website to check (using google video server): http://kissanime.com

Google Video CDN checker: http://redirector.c.youtube.com/report_mapping

This post has been edited by darrenliew96: Oct 23 2013, 11:54 PM
Alpha_Tay
post Oct 23 2013, 11:55 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
QUOTE(darrenliew96 @ Oct 23 2013, 11:50 PM)
One shocking discovery...
I found out that youtube works better with IPv6 cdn than the IPv4 CDN.

IPv6 CDN max speed 500kbps
user posted image

IPv4 CDN max speed 50kbps
user posted image

Can anyone confirm?
Best website to check (using google video server): http://kissanime.com

Google Video CDN checker: http://redirector.c.youtube.com/report_mapping
*
u just give TM a clue where to cap next.
maxiscool
post Oct 24 2013, 12:44 AM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 23 2013, 09:45 AM)
Recycle your Ethernet/wireless connection first, then try again.
*
Tested of reboot the system, but nothing happen. Weird things is that I'm able to see the DHCPv6 client IP address, only doesn't go out to the test-ipv6.com. Can even see on my client machine.
XeactorZ
post Oct 24 2013, 01:11 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
well phone can use ipv6 ?
darrenliew96
post Oct 24 2013, 01:42 AM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(XeactorZ @ Oct 24 2013, 01:11 AM)
well phone can use ipv6 ?
*
Some phone can.

Refer here:
http://en.wikipedia.org/wiki/Comparison_of...erating_systems

My iPhone running iOS 6.1.2 seems to have full IPv6 support including DHCPv6.
But mobile safari won't recognize IPv6 address.
It sometimes uses IPv6 address, and sometimes uses IPv4[very hard to differentiate cause of DNS]
The wifi settings also don't include any IPv6 info.
Need to download third party app eg:ip6config to view IPv6 info.

This post has been edited by darrenliew96: Oct 24 2013, 01:45 AM
XeactorZ
post Oct 24 2013, 02:27 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(darrenliew96 @ Oct 24 2013, 01:42 AM)
Some phone can.

Refer here:
http://en.wikipedia.org/wiki/Comparison_of...erating_systems

My iPhone running iOS 6.1.2 seems to have full IPv6 support including DHCPv6.
But mobile safari won't recognize IPv6 address.
It sometimes uses IPv6 address, and sometimes uses IPv4[very hard to differentiate cause of DNS]
The wifi settings also don't include any IPv6 info.
Need to download third party app eg:ip6config to view IPv6 info.
*
hmm me mainly using s3 and note 2
wonder how to enable ?

btw this few days keep frequent dc again, but phone can connect doh.gif
asellus
post Oct 24 2013, 07:22 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 24 2013, 12:44 AM)
Tested of reboot the system, but nothing happen. Weird things is that I'm able to see the DHCPv6 client IP address, only doesn't go out to the test-ipv6.com. Can even see on my client machine.
*
Can you make a screenshot of the bolded thing? With routerOS 6.5, DHCPv6 isn't supported yet.
Alpha Wolf
post Oct 24 2013, 07:30 AM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(Kiding @ Oct 23 2013, 10:51 PM)
Finally got my TP-Link TL-WR841ND v7 with OpenWRT 12.09 IPV6 working properly after two nights of studying and troubleshooting.

Attached Image

Now my Windows, Solaris, iPad and Android phone are getting ipv6  flex.gif  laugh.gif

Too bad TM not giving fixed ipv6 address  sleep.gif
*
good job rclxms.gif Took me slightly longer to get it all figured out in dd-wrt. Good to see that the LAN and WAN prefixes are indeed different.


QUOTE(XeactorZ @ Oct 24 2013, 02:27 AM)
hmm me mainly using s3 and note 2
wonder how to enable ?

btw this few days keep frequent dc again, but phone can connect doh.gif
*
My S2 support IPv6 out-of-the-box without any extra settings, so I'm assuming S3 and Note 2 and any products later should. Just make sure your web browser app supports IPv6. I tested it on Dolphin.
nymerine
post Oct 24 2013, 01:42 PM

Enthusiast
*****
Senior Member
920 posts

Joined: May 2010


Innacomm W7100N supports Ipv6.
OngHoeYuan0214
post Oct 24 2013, 03:39 PM

New Member
*
Newbie
0 posts

Joined: Oct 2013


Hi,
My Modem D-Link DSL-2730E gt IPv6 DNS and IP already
DHCPv6 Mode Set to Auto Mode already
Why my compuer IPv6 still is No Internet Access..
Help please..
Alpha Wolf
post Oct 24 2013, 03:42 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(OngHoeYuan0214 @ Oct 24 2013, 03:39 PM)
Hi,
My Modem D-Link DSL-2730E gt IPv6 DNS and IP already
DHCPv6 Mode Set to Auto Mode already
Why my compuer IPv6 still is No Internet Access..
Help please..
*
Have you actually tired restarting both the modem and your computer?
XeactorZ
post Oct 24 2013, 05:06 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 24 2013, 07:30 AM)
My S2 support IPv6 out-of-the-box without any extra settings, so I'm assuming S3 and Note 2 and any products later should. Just make sure your web browser app supports IPv6. I tested it on Dolphin.
*
how to check whether support or not
btw this 2 days get frequent dc again doh.gif
Alpha Wolf
post Oct 24 2013, 05:22 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 24 2013, 05:06 PM)
how to check whether support or not
btw this 2 days get frequent dc again doh.gif
*
Make sure that you are connected to an IPv6 network then visit a site like test-ipv6.com to test your ipv6 connectivity. Most mobile internet do not have ipv6 yet like my umobile.

Here's my test in chome browser app:
Attached Image

My S2 doesn't show the ipv6 address in the wifi connection details nor the phone status page but that test site shows my ipv6 address and it has full 10/10 v6 connectivity.

Btw, this post is sent from my S2 for extra testing too.

As for your dc issues, do you think it's related to your firmware update?
XeactorZ
post Oct 24 2013, 05:25 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 24 2013, 05:22 PM)
Make sure that you are connected to an IPv6 network then visit a site like test-ipv6.com to test your ipv6 connectivity. Most mobile internet do not have ipv6 yet like my umobile.

Here's my test in chome browser app:
Attached Image

My S2 doesn't show the ipv6 address in the wifi connection details nor the phone status page but that test site shows my ipv6 address and it has full 10/10 v6 connectivity.

Btw, this post is sent from my S2 for extra testing too.

As for your dc issues, do you think it's related to your firmware update?
*
later I try
but I thought only 1.06 firmware can enable ipv6 while 1.01 can't enable ?

and normally is related to firmware update issue, my phone normally can connect while computer sometime showing ! icon at bottom right hand site (wi-fi signal bar)
Alpha Wolf
post Oct 24 2013, 05:47 PM

Getting Started
**
Junior Member
263 posts

Joined: Mar 2008
From: SS2, Petaling Jaya


QUOTE(XeactorZ @ Oct 24 2013, 05:25 PM)
later I try
but I thought only 1.06 firmware can enable ipv6 while 1.01 can't enable ?

and normally is related to firmware update issue, my phone normally can connect while computer sometime showing !  icon at bottom right hand site (wi-fi signal bar)
*
Yeah, unfortunately v6 cannot be enabled with 1.01 because the dual wan checkbox is disabled on the web interface, so an upgrade is required to use v6 but I am hesitant to update because of the dc issues you're facing in 1.06.

I'm using my asus rt-n66u running on dd-wrt for v6 by the way. I'm glad that I no longer have to depend on that L7 router and can now use it for testing/development.
maxiscool
post Oct 24 2013, 11:11 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 24 2013, 07:22 AM)
Can you make a screenshot of the bolded thing? With routerOS 6.5, DHCPv6 isn't supported yet.
*
Thanks, @asellus for pointing out & @rizvanrp for the step by step guide. Update to routerOS 6.5 and re-configure seems solving my issue.
Finally, managed to visit test-ipv6.com and get 10/10 results.

I was referring to the IPV6 address I get in my Windows clients. Not quite understand DHCPv6 difference that IPv6 address in this case.

This post has been edited by maxiscool: Oct 24 2013, 11:15 PM
maxiscool
post Oct 24 2013, 11:13 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(maxiscool @ Oct 24 2013, 11:11 PM)
Thanks, @asellus for pointing out. Update to routerOS 6.5 and re-configure seems solving my issue.
Finally, managed to visit test-ipv6.com and get 10/10 results.

I was referring to the IPV6 address I get in my Windows clients. Not quite understand DHCPv6 difference that IPv6 address in this case.
*
Update:- Manage to get IPV6 if using Chrome. Safari doesnt seems to interpret correctly.

How come my post do not have IPV6 indicator as other forumer despite success in test-ipv6.com

This post has been edited by maxiscool: Oct 24 2013, 11:13 PM
XeactorZ
post Oct 25 2013, 12:17 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(Alpha Wolf @ Oct 24 2013, 05:47 PM)
Yeah, unfortunately v6 cannot be enabled with 1.01 because the dual wan checkbox is disabled on the web interface, so an upgrade is required to use v6 but I am hesitant to update because of the dc issues you're facing in 1.06.

I'm using my asus rt-n66u running on dd-wrt for v6 by the way. I'm glad that I no longer have to depend on that L7 router and can now use it for testing/development.
*
no wonder, but the router provided by TM really cannot use
when free also need go buy 1 doh.gif
maxiscool
post Oct 25 2013, 09:12 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
I'm doing further test on the setup of IPv6 despite having 10/10 result on test-ipv6.com.

I disable the IPv4 interface and left the IPv6 turn on only. (reboot router and windows interface just in case), and i get an IPv6 address.

And when I try to ping www.google.com, it request time out, is this the expected results?
darrenliew96
post Oct 25 2013, 09:28 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


Maxiscool: No. This is not the expected result. It should be able to get reply from google.com with IPv6 address.
What device are you using? PC or Phone?

How to find out your IPv6 really work?

Solution: disable or just make your IPv4 address change to static while simply randomize and input gateway IP.
Leave IPv6 settings auto assign by DHCPv6.
Then try to ping and surf www.google.com
If can surf, that means your IPv6 is ready to be used.

This post has been edited by darrenliew96: Oct 25 2013, 09:31 PM
Kiding
post Oct 25 2013, 10:04 PM

Regular
******
Senior Member
1,134 posts

Joined: Jan 2003
From: Seri Kembangan


QUOTE(maxiscool @ Oct 25 2013, 09:12 PM)
I'm doing further test on the setup of IPv6 despite having 10/10 result on test-ipv6.com.

I disable the IPv4 interface and left the IPv6 turn on only. (reboot router and windows interface just in case), and i get an IPv6 address.

And when I try to ping www.google.com, it request time out, is this the expected results?
*
I just did the same test, disable ipv4 protocol in the interface, and access lowyat forum again, no problem, but I couldn't access most of the sites due to not ipv6 enabled web site

I can see your post in lowyat does have the IPV6 tag, your ipv6 should work.

darrenliew96
post Oct 25 2013, 10:10 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


The IPv6 of lowyat is recently implemented?
maxiscool
post Oct 25 2013, 10:40 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(darrenliew96 @ Oct 25 2013, 09:28 PM)
Maxiscool: No. This is not the expected result. It should be able to get reply from google.com with IPv6 address.
What device are you using? PC or Phone?

How to find out your IPv6 really work?

Solution: disable or just make your IPv4 address change to static while simply randomize and input gateway IP.
Leave IPv6 settings auto assign by DHCPv6.
Then try to ping and surf www.google.com
If can surf, that means your IPv6 is ready to be used.
*
Hi Darrenliew96, I'm using a PC. Apparently I've figured out the root cause, it is the DNS not assigned to my device, manually insert in the DNS field on the PC, it works surfing to www.google.com and forum.lowyat.net.

Now, I need to figure how I correct this config, any help?
darrenliew96
post Oct 25 2013, 10:43 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(maxiscool @ Oct 25 2013, 10:40 PM)
Hi Darrenliew96, I'm using a PC. Apparently I've figured out the root cause, it is the DNS not assigned to my device, manually insert in the DNS field on the PC, it works surfing to www.google.com and forum.lowyat.net.

Now, I need to figure how I correct this config, any help?
*
Try this two google IPv6 DNS

2001:4860:4860::8888
2001:4860:4860::8844


For IPv4
8.8.8.8
8.8.4.4
maxiscool
post Oct 25 2013, 10:57 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Thanks, this will work if I manually entered in each client/PC.

But I'm trying to check how come it is not push to each client as the correct DNS without manual input.
asellus
post Oct 25 2013, 11:00 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 25 2013, 10:57 PM)
Thanks, this will work if I manually entered in each client/PC.

But I'm trying to check how come it is not push to each client as the correct DNS without manual input.
*
You cannot do that if you use Windows PC, the router is routerOS and disabled the IPv4 stack in Windows.
maxiscool
post Oct 25 2013, 11:13 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Not quite understand that, but I'm trying in PC and MAC. What you mean is that Windows need manual input? My MAC also need manual input. Is that anything i need to look at ?
asellus
post Oct 25 2013, 11:34 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


Your Mac run what OS X version?
maxiscool
post Oct 25 2013, 11:46 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Maverick..
asellus
post Oct 25 2013, 11:54 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


Then if you tell routerOS to advertise DNS servers via RA OS X should picked it up automatically. Windows just ignore those advertisement.
maxiscool
post Oct 26 2013, 12:00 AM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Thanks once again, change the settings at ND. Now MAC able to pull DNS automatically.

Can give a brief on which MAC onwards this will work? Ubuntu linux will works?

For Windows, no solution? To use IPv6 with routerOS, i need to manually input v6 DNS?
asellus
post Oct 26 2013, 12:14 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 26 2013, 12:00 AM)
Thanks once again, change the settings at ND. Now MAC able to pull DNS automatically.

Can give a brief on which MAC onwards this will work? Ubuntu linux will works?

For Windows, no solution? To use IPv6 with routerOS, i need to manually input v6 DNS?
*
OSX Lion and above, all Linux distros should be OK too. Windows doesn;t therefore Ipv4 stack has to be enabled at all times there, or need to install rdnssd-win32.
maxiscool
post Oct 26 2013, 12:22 AM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
Thanks @asellus for the explanation. OK, will try with Linux once perform the installation.

For windows, is that limited to RouterOS and Windows or other router will be perform good? Even latest Windows 8.1 will not be resolving this issue?
asellus
post Oct 26 2013, 12:27 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Oct 26 2013, 12:22 AM)
Thanks @asellus for the explanation. OK, will try with Linux once perform the installation.

For windows, is that limited to RouterOS and Windows or other router will be perform good? Even latest Windows 8.1 will not be resolving this issue?
*
If Mikrotik actually comes around and actually implement a fully working DHCPv6, then there should be no problem. We will not probably see this until version 7 though.

If you use a router with fully-working DHCPv6 like OpenWRT Barrier Breaker, then IPv6 DNS will be configured automatically in Windows.


TSwKkaY
post Oct 26 2013, 01:58 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(darrenliew96 @ Oct 25 2013, 10:10 PM)
The IPv6 of lowyat is recently implemented?
*
The first record of our implementation was in December 2010: https://forum.lowyat.net/topic/1420285?author=wKkaY
joeboto
post Oct 26 2013, 10:39 AM

insert title
*****
Senior Member
913 posts

Joined: Jun 2006


testing to see is there ipv6 on my post.

EDITED: nope cry.gif

This post has been edited by joeboto: Oct 26 2013, 10:40 AM
darrenliew96
post Oct 26 2013, 12:11 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(joeboto @ Oct 26 2013, 10:39 AM)
testing to see is there ipv6 on my post.

EDITED: nope  cry.gif
*
Disable IPv4 and try again.
Some browser will preferred IPv4 rather than IPv6.
I don't know how the dual stack logic works, but I know they prefer IPv4 because it doesn't need to wait for IPv6 packets to reach to the device, thus decrease timeout period.
Just like the iOS.

<TIPS>
How to load IPv6 address in browser?

For example:
this is Google's IPv6 address
2404:6800:4001:c01::65
http://[2404:6800:4001:c01::65]

You just need to add the square brackets [] at the address in address bar.
For example:
user posted image

[Latest announcement]
Looks like TM had posted IPv6 faq at their FAQ homepage.
https://www.tm.com.my/OnlineHelp/CustomerSu...Pages/FAQs.aspx

This post has been edited by darrenliew96: Oct 26 2013, 07:52 PM
asellus
post Oct 26 2013, 07:19 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


Anyone here knows if TM uses any other IPv6 transit providers other than Hurricane Electric?
TSwKkaY
post Oct 26 2013, 09:03 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 26 2013, 07:19 PM)
Anyone here knows if TM uses any other IPv6 transit providers other than Hurricane Electric?
*
Checked out a looking glass and saw that they also use NTT, C&W, Sprint.

And for what it's worth, lowyat.net's hosting provider isn't peered with TMNet at MyIX. Not sure when it will be complete hmm.gif
asellus
post Oct 26 2013, 10:40 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


2401:3400:2000:1::17 isn't in Singapore right, because tracert sure looks like it.
TSwKkaY
post Oct 27 2013, 02:07 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(asellus @ Oct 26 2013, 10:40 PM)
2401:3400:2000:1::17 isn't in Singapore right, because tracert sure looks like it.
*
It's in AIMS @ Jalan Raja Chulan.
asellus
post Oct 27 2013, 08:50 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


The then IPv6 routing isn't really efficient then, just like for Facebook and Yahoo. That's why streaming videos from Facebook isn't really smooth here.

Very few IPv6 websites in US can be connected via non-HE transit, sees only C&W, Cogent and Atrato (EU).
jutamind
post Oct 27 2013, 09:55 PM

Look at all my stars!!
*******
Senior Member
2,429 posts

Joined: Jul 2007
did TM upgrade dlink dir-615 firmware remotely recently? just now i realized that i couldnt browse and i tried to login to my router using the operator username but couldnt login anymore.

luckily i can still login using my admin username. i checked and found my firmware is now 7.17 instead of the original 7.09 and operator username and password and cannot be used anymore.
darrenliew96
post Oct 27 2013, 10:04 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(jutamind @ Oct 27 2013, 09:55 PM)
did TM upgrade dlink dir-615 firmware remotely recently? just now i realized that i couldnt browse and i tried to login to my router using the operator username but couldnt login anymore.

luckily i can still login using my admin username. i checked and found my firmware is now 7.17 instead of the original 7.09 and operator username and password and cannot be used anymore.
*
You port forward your router telnet or Webadmin?
If no, then is most likely auto update.
jutamind
post Oct 27 2013, 10:51 PM

Look at all my stars!!
*******
Senior Member
2,429 posts

Joined: Jul 2007
QUOTE(darrenliew96 @ Oct 27 2013, 10:04 PM)
You port forward your router telnet or Webadmin?
If no, then is most likely auto update.
*
No port forward
powerwoot
post Oct 28 2013, 06:25 PM

讨厌的 ubuntu
*******
Senior Member
2,930 posts

Joined: Jan 2007
From: Kolej Universiti Agrosains Malaysia, Melaka



Does anyone have the router screenshot for D-Link DSL2730E that is working for IPv6? I tried any IPv6 settings in it but still no internet, only IPv4 that is working. Just want to check which part I've been left unattended. Thanks.
TSwKkaY
post Oct 28 2013, 06:53 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
I have split off the Youtube discussion to https://forum.lowyat.net/topic/3010305

Please center this discussion around TMnet and IPv6.
paultantk
post Oct 28 2013, 09:16 PM

Casual
***
Junior Member
407 posts

Joined: Jan 2003


QUOTE(wKkaY @ Oct 26 2013, 09:03 PM)
Checked out a looking glass and saw that they also use NTT, C&W, Sprint.

And for what it's worth, lowyat.net's hosting provider isn't peered with TMNet at MyIX. Not sure when it will be complete hmm.gif
*
Just to clarify... IPS1 peered with IPv4 and not with IPv6?
TSwKkaY
post Oct 28 2013, 09:39 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(paultantk @ Oct 28 2013, 09:16 PM)
Just to clarify... IPS1 peered with IPv4 and not with IPv6?
*
Ja!
ssslayerrr
post Oct 29 2013, 07:05 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


Followed the instructions from TMNET, it now works at my home near Sg Long, but not at my workplace, near Jalan Kuchai Lama, TMNETs DHCPv6 not giving out ipv6 prefixes there. Same router, both sides, Asus RT-N16.

Security is a big issue, since I was previously behind the router's firewall, so everything was open within my network, and ASUS's firmware does not support ipv6 firewall.
Initially, doing an IPv6 port scan here showed a lot of the common were open and responding from the internet!!

ipv6.chappell-family.com/ipv6tcptest/

Fortunately merlins firmware for the RT N16 does enable an ipv6 firewall, he supports a few routers.

http://www.lostrealm.ca/tower/node/79

So now my rt n16 firewalls ipv6 traffic, and a recheck shows that all my ports are in stealth mode now. Saved me the pain of having to secure each pc in my network.

Anyway, for the RT-N16, you just need to click on the ipv6 tab on the left navigation bar, then choose 'Native' as the connection type, 'PPP' interface, and enable DHCP-PD. If you are using merlin's firmware, you can then go the the firewall tab and enable the ipv6 firewall there, but it's enabled by default.

As for my workplace at Kuchai Lama, its really frustrating. I have IPv6 connectivity from the router itself, I can ping ipv6.google.com from the router, but Router Advertisement is disabled because radvd can't get the ipv6 prefix from TMNET.

radvd[439]: no auto-selected prefix on interface br0, disabling advertisements.

If only there is a way for me to specify my own prefix......, have been looking this up but to no avail.
TSwKkaY
post Oct 29 2013, 07:14 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(ssslayerrr @ Oct 29 2013, 07:05 PM)
Security is a big issue, since I was previously behind the router's firewall, so everything was open within my network, and ASUS's firmware does not support ipv6 firewall.
*
Yup a host-based firewall becomes important in an IPv6 setup.

IMO you negate many of the end-to-end benefits of IPv6 by using a firewall at the router to block incoming tcp connections by default.
ssslayerrr
post Oct 29 2013, 07:40 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


Wouldn't a host based firewall block unsolicited tcp connections as well?

TSwKkaY
post Oct 29 2013, 08:59 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(ssslayerrr @ Oct 29 2013, 07:40 PM)
Wouldn't a host based firewall block unsolicited tcp connections as well?
*
Yes, however the difference is where control lies. A host-based firewall can be configured by the host, either manually by the user or programatically like Windows INetFwRule. I think the Windows implementation is pretty nice where it gives you the choice of trusted/untrusted whitelist for each network you join and each application.

With a perimeter firewall, how would a home user do that? I believe troubleshooting firewalls or logging into one's router to edit firewall rules is beyond most lusers ability - and that is assuming the ISP even offer that option. TM for example is known not to disclose password to their routers.

UPNP to punch holes in the firewall? A complicated solution to a problem which should be solved at the host anyway. For example, what if you bring your computer somewhere which doesn't block incoming connections by default? You will want a host firewall protecting you by default.

Perimeter firewalls still have their place to enforce security in depth, but it should be in addition to host firewalls and not in place of it... and for it to be effective it should be locked down with no way for holes to be punched by hosts.
prasys
post Oct 29 2013, 09:16 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(hinamoriamu @ Oct 22 2013, 10:10 AM)
Just one curious question
If TM never assign a public IPv4 address, will IPv6 will help them to resolve the issue for CCTV or IPCam port forwarding?
*
As answered earlier uh , yes and no.

Your CCTV/IP camera needs to support IPV6. It is useless and most ones I have seen does not even have ipv6 stack installed (my cctv for instance runs on old linux 2.4.x kenrel without ipv6 compiled). So it is useless , even if my Telco network supports ipv6 and my router is able to handle IPV6 , but the device itself is not compatible with IPV6

QUOTE(XeactorZ @ Oct 24 2013, 01:11 AM)
well phone can use ipv6 ?
*
Yes , Android 4.x and iOS 5 and above supports IPV6. Not sure about earlier version of Android as I have not tested before

The phone might not show it has a IPV6 address under Settings , but try surfing with a browser and it is able to view IPV6 content and for some reason , like iPhone with iOS 7 for instance , it seems to prefer to fall back to ipv4 instead of ipv6 , when it is given a choice between the two.
ssslayerrr
post Oct 29 2013, 09:19 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


QUOTE(wKkaY @ Oct 29 2013, 08:59 PM)
Yes, however the difference is where control lies. A host-based firewall can be configured by the host, either manually by the user or programatically like Windows INetFwRule. I think the Windows implementation is pretty nice where it gives you the choice of trusted/untrusted whitelist for each network you join and each application.

With a perimeter firewall, how would a home user do that? I believe troubleshooting firewalls or logging into one's router to edit firewall rules is beyond most lusers ability - and that is assuming the ISP even offer that option. TM for example is known not to disclose password to their routers.

UPNP to punch holes in the firewall? A complicated solution to a problem which should be solved at the host anyway. For example, what if you bring your computer somewhere which doesn't block incoming connections by default? You will want a host firewall protecting you by default.

Perimeter firewalls still have their place to enforce security in depth, but it should be in addition to host firewalls and not in place of it... and for it to be effective it should be locked down with no way for holes to be punched by hosts.
*
Thanks for the explanation dude, understood, I totally didn't think of that, but now that you explained it, it seems so obvious
darrenliew96
post Oct 29 2013, 10:03 PM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(prasys @ Oct 29 2013, 09:16 PM)
As answered earlier uh , yes and no.

Your CCTV/IP camera needs to support IPV6. It is useless and most ones I have seen does not even have ipv6 stack installed (my cctv for instance runs on old linux 2.4.x kenrel without ipv6 compiled). So it is useless , even if my Telco network supports ipv6 and my router is able to handle IPV6 , but the device itself is not compatible with IPV6
Yes , Android 4.x and iOS 5 and above supports IPV6. Not sure about earlier version of Android as I have not tested before

The phone might not show it has a IPV6 address under Settings , but try surfing with a browser and it is able to view IPV6 content and for some reason , like iPhone with iOS 7 for instance , it seems to prefer to fall back to ipv4 instead of ipv6 , when it is given a choice between the two.
*
iOS kernel is based on Mac OSX darwin BSD kernel.
The operating system kernel itself will constantly select what is best for communication based on latency and speed.
TSwKkaY
post Oct 29 2013, 10:20 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(prasys @ Oct 29 2013, 09:16 PM)
Your CCTV/IP camera needs to support IPV6. It is useless and most ones I have seen does not even have ipv6 stack installed (my cctv for instance runs on old linux 2.4.x kenrel without ipv6 compiled). So it is useless , even if my Telco network supports ipv6 and my router is able to handle IPV6 , but the device itself is not compatible with IPV6
*
A possible bandaid is to setup a IPv6-to-IPv4 proxy. With practically unlimited IPv6 addresses, you can even assign 1 IPv6 IP to 1 internal IPv4.
prasys
post Oct 29 2013, 10:26 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(wKkaY @ Oct 29 2013, 10:20 PM)
A possible bandaid is to setup a IPv6-to-IPv4 proxy. With practically unlimited IPv6 addresses, you can even assign 1 IPv6 IP to 1 internal IPv4.
*
Thanks for the heads up. Didn't think of that , I am still searching the source code or any sort of information about the cctv in the internet so that it would be possible to recompile with ipv6 stack
Victek
post Oct 30 2013, 05:05 PM

New Member
*
Newbie
0 posts

Joined: Aug 2008
IPv6 test with Tomato RAF firmware runs well.

@ssslayerrr , you can try other firmware versions where prefix options are enabled ....

This post has been edited by Victek: Oct 30 2013, 05:12 PM


Attached thumbnail(s)
Attached Image
ssslayerrr
post Oct 30 2013, 06:07 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


QUOTE(Victek @ Oct 30 2013, 05:05 PM)
IPv6 test with Tomato RAF firmware runs well.

@ssslayerrr , you can try other firmware versions where prefix options are enabled ....
*
Hi, hahaha, the man himself. I've used your tomato firmware on my wrt54gl s, thanks for that. Actually, the Asus firmware allows me to disable the dhcp-pd and hence, specify my own prefixes, it's just that I have no idea on what to put in there, just blindly googling now hoping to find some info on this, no luck so far......


Victek
post Oct 30 2013, 06:24 PM

New Member
*
Newbie
0 posts

Joined: Aug 2008
OK, just posted here by other forum members comments and the lack of knowledge about ipv6 ....everybody wants, ISP's offer as commercial advantage but infrastructure not ready ...
Moogle Stiltzkin
post Oct 30 2013, 08:31 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:42 AM
DellMalaysia
post Nov 2 2013, 09:43 PM

Kindly look at my previous successful threads
*****
Senior Member
735 posts

Joined: Sep 2013
From: IYD ~ In Your Dream



anybody got problem with his ipv6 slow connectivity? my unifi is 5mb and 20mb. both decreased to 2mb and 11mb. if i change back to ipv4, speed came back to normal. why? please help. thank you.
ikemaman
post Nov 5 2013, 05:55 AM

New Member
*
Junior Member
4 posts

Joined: Jun 2009
QUOTE(XeactorZ @ Oct 3 2013, 05:50 PM)
thanks
I think my model is Model L7 since I have the design
however I can't tick dual LAN, any idea ?

refer the photo
*
same here. how do you resolve the problem?
Moogle Stiltzkin
post Nov 5 2013, 08:21 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:42 AM
XeactorZ
post Nov 5 2013, 04:07 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(ikemaman @ Nov 5 2013, 05:55 AM)
same here. how do you resolve the problem?
*
I didn't enable ipv6
just ignore it

yet still getting frequent dc
andrew9292
post Nov 5 2013, 06:43 PM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


How would the configuration be in OpenWRT? There are so many options & methods, have tried it for a day and still no go. Even broke the DHCP and probably some other stuff, now i'm back with TM's router.

I'm using TM's DIR615 as a VLAN Bridge, stripped the v.500 there.
With a DIR615-C2 on OpenWRT to simply dail PPPoE via the bridge.
That's for IPv4.

So what direction should i be heading? What packages to download and what to input? I'm not a network guy i just follow online instructions really well tongue.gif

If i get it correctly, what i need to do is configure it for Dual-Stack as we're running ipv6 concurrently with v4.
And TM uses SLAAC with DHCPv6 to assign addresses.
The address needs to be routed to clients via something like radvd, something like a DHCP for ipv6?
Anything else needed? 6to4 / 6rd?

At one point i managed to get TM's ipv6 assigned address.
But there was no network connectivity, some routing somewhere didnt work out...
I'm veri confused rclxub.gif
Any detailed guides or ideas? notworthy.gif

This post has been edited by andrew9292: Nov 5 2013, 06:46 PM
ssslayerrr
post Nov 5 2013, 09:25 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


QUOTE(andrew9292 @ Nov 5 2013, 06:43 PM)
How would the configuration be in OpenWRT? There are so many options & methods, have tried it for a day and still no go. Even broke the DHCP and probably some other stuff, now i'm back with TM's router.

I'm using TM's DIR615 as a VLAN Bridge, stripped the v.500 there.
With a DIR615-C2 on OpenWRT to simply dail PPPoE via the bridge.
That's for IPv4.

So what direction should i be heading? What packages to download and what to input? I'm not a network guy i just follow online instructions really well tongue.gif

If i get it correctly, what i need to do is configure it for Dual-Stack as we're running ipv6 concurrently with v4.
And TM uses SLAAC with DHCPv6 to assign addresses.
The address needs to be routed to clients via something like radvd, something like a DHCP for ipv6?
Anything else needed? 6to4 / 6rd?

At one point i managed to get TM's ipv6 assigned address.
But there was no network connectivity, some routing somewhere didnt work out...
I'm veri confused rclxub.gif
Any detailed guides or ideas? notworthy.gif
*
I have access to 3 locations with unifi and all 3 have different 'situations'.

No. 1. The first location gets an wan, lan ipv6 address and lan prefix, ipv6 works with tm's dir 615, but now I'm using the asus RT N16 over there. no problems.

No. 2. The second location is able to get a wan ipv6 address, but no lan ipv6 address and no lan prefix, so, while the router itself has ipv6 internet connectivity (can ping ipv6.google.com etc), the lan clients don't.

No. 3. The third location, doesnt even get a wan ipv6 address.

So, it could be very frustrating trying to configure it when it might not be 'fully' available. I suggest you try tm's dir 615 router first and confirm that you are getting complete ipv6 functionality, if you are, then go ahead and try openwrt.

What you describe in your last paragraph sounds like the my situation no. 2, ie, your area is not getting ipv6 prefixes from tmnet yet.
asellus
post Nov 5 2013, 11:09 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(andrew9292 @ Nov 5 2013, 06:43 PM)
How would the configuration be in OpenWRT? There are so many options & methods, have tried it for a day and still no go. Even broke the DHCP and probably some other stuff, now i'm back with TM's router.

I'm using TM's DIR615 as a VLAN Bridge, stripped the v.500 there.
With a DIR615-C2 on OpenWRT to simply dail PPPoE via the bridge.
That's for IPv4.

So what direction should i be heading? What packages to download and what to input? I'm not a network guy i just follow online instructions really well tongue.gif

If i get it correctly, what i need to do is configure it for Dual-Stack as we're running ipv6 concurrently with v4.
And TM uses SLAAC with DHCPv6 to assign addresses.
The address needs to be routed to clients via something like radvd, something like a DHCP for ipv6?
Anything else needed? 6to4 / 6rd?

At one point i managed to get TM's ipv6 assigned address.
But there was no network connectivity, some routing somewhere didnt work out...
I'm veri confused rclxub.gif
Any detailed guides or ideas? notworthy.gif
*
Assuming that you use Barrier Breaker, all you need to do is to run a DHCPv6-PD client on '@wan' interface, assuming of course the PPPoE interface runs on 'wan' interface. No need to get a second /64 prefix, because OpenWRT can actually use the /64 supplied to the 'wan' interface for all supporting devices in your network.

Kinda work the opposite way of routerOS.
Sharingan
post Nov 5 2013, 11:28 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

Did u run successfully run Mikrotik with TM DHCP-PD ? Kinda wondering how's ur config looks like since i'm trying hard to follow the code and till now still return NULL . Well to be exact, i did get the address but i can't ping to ipv6.google.com nor www.kame.net .

My current setup:
Virtualbox 4.1.24
2 x Physical NIC
Mikrotik 5.25
ADSL 4M Streamyx

Few hours ago i did tried on pfSense 2.1-RELEASE , same condition met . Can't ping to both address at all and this time i'm quite sure that all my firewall rules are set for accept and forwarded properly. If else fails, i'll go back to tunnelbroker setup. Thanks for the attention and insights.
asellus
post Nov 6 2013, 12:06 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 5 2013, 11:28 PM)
@asellus

Did u run successfully run Mikrotik with TM DHCP-PD ? Kinda wondering how's ur config looks like since i'm trying hard to follow the code and till now still return NULL . Well to be exact, i did get the address but i can't ping to ipv6.google.com nor www.kame.net .

My current setup:
Virtualbox 4.1.24
2 x Physical NIC
Mikrotik 5.25
ADSL 4M Streamyx

Few hours ago i did tried on pfSense 2.1-RELEASE , same condition met . Can't ping to both address at all and this time i'm quite sure that all my firewall rules are set for accept and forwarded properly. If else fails, i'll go back to tunnelbroker setup. Thanks for the attention and insights.
*
Yes, that's how I do it. And actually is the only way to do it.

» Click to show Spoiler - click again to hide... «


Assuming you already have the PPPoE connection up and running, then:-

1. In 'IPv6 ---> DHCP client', add a DHCPv6 client on your PPPoE interface, give a name of the pool that will contain the /64 prefix given by TM.
2. Then, in 'IPv6 ---> Addresses', add a '::/64' address, specifying the pool name you have just created in step 1 above, run it on the interface you wanted it to run, and enable the 'Advertise' option.

With this, all devices connected to the interface you have specified at step 2 above should get IPv6 address(es) via SLAAC.
faizal87
post Nov 6 2013, 12:08 AM

piko piko pong pong
******
Senior Member
1,384 posts

Joined: Jan 2007
From: shah alam@ ampang



any advantages using ipv6?
Sharingan
post Nov 6 2013, 12:16 AM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

Ah the no.2, i did try that and yes i did get the address via SLAAC. Hmm must be my rules then. Would you mind compare mine with you then please,

CODE
/ipv6 firewall filter
add action=accept chain=input connection-state=established disabled=no \
   in-interface=ether1
add action=accept chain=forward connection-state=established disabled=no \
   in-interface=ether1
add action=accept chain=input connection-state=related disabled=no \
   in-interface=ether1
add action=accept chain=forward connection-state=related disabled=no \
   in-interface=ether1
add action=accept chain=input disabled=no dst-port=546 in-interface=ether1 \
   protocol=udp src-address=fe80::/16
add action=drop chain=input disabled=no in-interface=ether1
add action=drop chain=forward disabled=no in-interface=ether1
add action=accept chain=input comment="Allow established connections" \
   connection-state=established disabled=no



asellus
post Nov 6 2013, 12:34 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 6 2013, 12:16 AM)
@asellus

Ah the no.2, i did try that and yes i did get the address via SLAAC. Hmm must be my rules then. Would you mind compare mine with you then please,

CODE
/ipv6 firewall filter
add action=accept chain=input connection-state=established disabled=no \
   in-interface=ether1
add action=accept chain=forward connection-state=established disabled=no \
   in-interface=ether1
add action=accept chain=input connection-state=related disabled=no \
   in-interface=ether1
add action=accept chain=forward connection-state=related disabled=no \
   in-interface=ether1
add action=accept chain=input disabled=no dst-port=546 in-interface=ether1 \
   protocol=udp src-address=fe80::/16
add action=drop chain=input disabled=no in-interface=ether1
add action=drop chain=forward disabled=no in-interface=ether1
add action=accept chain=input comment="Allow established connections" \
   connection-state=established disabled=no

*
Something that looks like below:-

CODE

/ipv6 firewall filter
add action=accept chain=input comment="Router - Allow IPv6 ICMP" disabled=no protocol=icmpv6
add action=accept chain=input comment="Router - accept UDP traffic on port 546" disabled=no protocol=udp dst-port=546 in-interface="Streamyx PPPoE"
add action=accept chain=input comment="Router - Accept established connections" connection-state=established disabled=no
add action=accept chain=input comment="Router - Accept related connections" connection-state=related disabled=no
add action=drop chain=input comment="Router - Drop invalid connections" connection-state=invalid disabled=no
add action=accept chain=input comment="Router- UDP" disabled=no protocol=udp
add action=accept chain=input comment="Router - From our LAN" disabled=no in-interface=bridge-local
add action=drop chain=input comment="Router - Drop other traffic" disabled=no
add action=drop chain=forward comment="LAN - Drop invalid Connections" connection-state=invalid disabled=no
add action=accept chain=forward comment="LAN - Accept UDP" disabled=no protocol=udp
add action=accept chain=forward comment="LAN - Accept ICMPv6 " disabled=no protocol=icmpv6
add action=accept chain=forward comment="LAN - Accept established Connections" connection-state=established disabled=no
add action=accept chain=forward comment="LAN - Accept related connections" connection-state=related disabled=no
add action=accept chain=forward comment="LAN - Internal traffic" disabled=no in-interface=bridge-local
add action=log chain=forward comment="LAN - Log everything else" disabled=no log-prefix="Log IPv6"
add action=reject chain=forward comment="LAN - Drop everything else" connection-state=new disabled=no in-interface="Streamyx PPPoE" reject-with=icmp-no-route

Moogle Stiltzkin
post Nov 6 2013, 09:23 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:42 AM
teh_tarik_satu
post Nov 6 2013, 09:34 AM

Getting Started
**
Junior Member
140 posts

Joined: Jun 2011
noted!
faizal87
post Nov 6 2013, 09:55 AM

piko piko pong pong
******
Senior Member
1,384 posts

Joined: Jan 2007
From: shah alam@ ampang




QUOTE(Moogle Stiltzkin @ Nov 6 2013, 09:23 AM)
user posted image
1. more address space...
the first notable and obvious benefit, is for the entire netizen community, more ip addresses to accomodate more devices now and into the future  nod.gif thats one problem we can forget for now.
2. faster latency
You can run a test here
http://ipv6-test.com/pingtest/

well latency is most important for gamers. I remember a few years back when i was playing world of warcraft with Tmnut Adsl to the US server. I was averaging 600-800 MS latency. Barely playable as my reaction time was slower than other players, which is most noticeable in the battlegrounds and pvp. Basically i was playing with a nerf around my shoulders in terms of high latency  rclxub.gif

Then later i got Unifi 10mbps. My latency to US server these days around 200-300ms. This is drastically better  thumbup.gif
I suspect they achieve this by getting around the whole NAT deal in the router  hmm.gif
VOIP also benefits from lower latency. If you ever use teamspeak, Ventrilo, Mumble, skype..... you may have at some point come across latency issue, like delayed time before the message gets through via audio doh.gif So lower latency here means, less lag time between input/output of audio through the internet  cool.gif
3. improved security
IPv6 has several advantages over IPv4. IPv6 has several privacy enhancements: it has more encryption and authentication options, which ensures that networks are less susceptible to being compromised overall significantly more secure.

user posted image
4. p2p benefits
In addition IPv6 supports multicast, which saves network bandwidth by allowing bandwidth-intensive packet flows—such as multimedia streams—to simultaneously be sent to multiple destinations.

If that sounds confusing, well a very wise person (Confucious) once said, a picture is worth a thousand words  cool.gif

user posted image
But because now is still in the transistional period, there are some slight hickups for the meanwhile
5. Mobile devices retain IP addresses when moving from network to another on the go

Another advantage of IPv6 addressing is that when you're moving from place to place with your mobile device, you'll no longer need to worry with getting a new Internet address at every stop. With Mobile IPv6, whether your smartphone or tablet is connected to the Internet with Wi-Fi or WiMAX, your device should retain the same address.

If the wireless infrastructure around you is up to snuff, mobile IPv6 will let you seamlessly move from one form of wireless connectivity to another without losing your connection or needing to pick up a new IP address.
6. faster internet speed
*
» Click to show Spoiler - click again to hide... «
Moogle Stiltzkin
post Nov 6 2013, 09:56 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:44 AM
prasys
post Nov 6 2013, 01:42 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(Moogle Stiltzkin @ Nov 6 2013, 09:23 AM)
user posted image
1. more address space...
the first notable and obvious benefit, is for the entire netizen community, more ip addresses to accomodate more devices now and into the future  nod.gif thats one problem we can forget for now.
2. faster latency
You can run a test here
http://ipv6-test.com/pingtest/

well latency is most important for gamers. I remember a few years back when i was playing world of warcraft with Tmnut Adsl to the US server. I was averaging 600-800 MS latency. Barely playable as my reaction time was slower than other players, which is most noticeable in the battlegrounds and pvp. Basically i was playing with a nerf around my shoulders in terms of high latency  rclxub.gif

Then later i got Unifi 10mbps. My latency to US server these days around 200-300ms. This is drastically better  thumbup.gif

6. faster internet speed
*
WoW on IPV6 - latency is stable at 160ms. This is amazing , green latency

Even LFR times , it hovers around 201-210ms...
andrew9292
post Nov 6 2013, 02:03 PM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


QUOTE(ssslayerrr @ Nov 5 2013, 09:25 PM)
I have access to 3 locations with unifi and all 3 have different 'situations'.

No. 1. The first location gets an wan, lan ipv6 address and lan prefix, ipv6 works with tm's dir 615, but now I'm using the asus RT N16 over there. no problems.

No. 2. The second location is able to get a wan ipv6 address, but no lan ipv6 address and no lan prefix, so, while the router itself has ipv6 internet connectivity (can ping ipv6.google.com etc), the lan clients don't.

No. 3. The third location, doesnt even get a wan ipv6 address.

So, it could be very frustrating trying to configure it when it might not be 'fully' available. I suggest you try tm's dir 615 router first and confirm that you are getting complete ipv6 functionality, if you are, then go ahead and try openwrt.

What you describe in your last paragraph sounds like the my situation no. 2, ie, your area is not getting ipv6 prefixes from tmnet yet.
*
Followed your suggestion and enabled ipv6 at TM's 615. It worked!
But I dont want to use their router and i found out it works well on OpenWRT thanks to Asellus!

QUOTE(asellus @ Nov 5 2013, 11:09 PM)
Assuming that you use Barrier Breaker, all you need to do is to run a DHCPv6-PD client on '@wan' interface, assuming of course the PPPoE interface runs on 'wan' interface. No need to get a second /64 prefix, because OpenWRT can actually use the /64 supplied to the 'wan' interface for all supporting devices in your network.

Kinda work the opposite way of routerOS.
*
Nope, I was on Attitude Adjustment before this and you triggered my curiosity on Barrier Breaker.
The problem with Barrier Breaker is that the current version takes up too much space on my DIR615-C2 4MB flash, unable to install the graphic user interface at all... hopefull this changes when the release candidate / final is out.

After doing the basic configs via SSH and just adding [option ipv6 '1'] into /etc/config/network
It works completely without problem! Much simpler than Attitude adjustment notworthy.gif

----

I found that if I dont input Google/ OpenDNS's IPv6 address, test-ipv6.com shows that ISP DNS cannot resolve IPv6.
Turning off IPv4 in Network Preferences without inputing IPv6 DNS results in lost in connectivity
saturn85
post Nov 6 2013, 03:48 PM

Folding@home
*******
Senior Member
8,686 posts

Joined: Mar 2009



QUOTE(Moogle Stiltzkin @ Nov 6 2013, 09:23 AM)
» Click to show Spoiler - click again to hide... «

*
good info. thumbup.gif

This post has been edited by saturn85: Nov 6 2013, 03:50 PM
yeam
post Nov 6 2013, 05:26 PM

New Member
*
Junior Member
16 posts

Joined: Dec 2005


Noob question.

How to configure router/client to use "IPv6"?

Router: Asus RT-N56u

From the rounter ping tool service "ipv6.google.com".

Seem the router got IPv6 WAN IP.

user posted image

but the client doesn't pick up any IPv6 address.

How can i proceed from bellow? need some manual config? or everythings should be handle by DHCP?

user posted image

user posted image
ssslayerrr
post Nov 6 2013, 05:37 PM

Enthusiast
*****
Senior Member
805 posts

Joined: Dec 2004


QUOTE(yeam @ Nov 6 2013, 05:26 PM)
Noob question.

How to configure router/client to use "IPv6"?

Router: Asus RT-N56u

From the rounter ping tool service "ipv6.google.com".

Seem the router got IPv6 WAN IP.

user posted image

but the client doesn't pick up any IPv6 address.

How can i proceed from bellow? need some manual config? or everythings should be handle by DHCP?

user posted image

user posted image
*
I don't see anything wrong with your config, its the same as my Asus RT N16. Not much more you can do, other than wait till tm starts giving out lan prefixes to your area. If you click on System Log>IPV6, you will see that you have a wan ipv6 address, but no lan ipv6 address, no prefix either.
Nickimaru
post Nov 6 2013, 08:03 PM

Getting Started
**
Junior Member
58 posts

Joined: Feb 2009
From: Kuala Lumpur, Malaysia


Yay, managed to configure IPv6 on my router biggrin.gif
» Click to show Spoiler - click again to hide... «

wKkaY: For the router database:

Router model ASUS RT-N56U
Firmware Padavan RT-N56U_3.4.3.6-069 (firmware link)
Broadband package UniFi Home VIP20

This post has been edited by Nickimaru: Nov 6 2013, 08:07 PM
TSwKkaY
post Nov 6 2013, 08:20 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(Nickimaru @ Nov 6 2013, 08:03 PM)
Yay, managed to configure IPv6 on my router biggrin.gif
» Click to show Spoiler - click again to hide... «

wKkaY: For the router database:

Router model ASUS RT-N56U
Firmware Padavan RT-N56U_3.4.3.6-069 (firmware link)
Broadband package UniFi Home VIP20
*
Thanks Nicholas!
prasys
post Nov 6 2013, 08:24 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(yeam @ Nov 6 2013, 05:26 PM)
Noob question.

How to configure router/client to use "IPv6"?

Router: Asus RT-N56u

From the rounter ping tool service "ipv6.google.com".

Seem the router got IPv6 WAN IP.

user posted image

but the client doesn't pick up any IPv6 address.

How can i proceed from bellow? need some manual config? or everythings should be handle by DHCP?

user posted image

user posted image
*
Stock Firmware ? Get rid of it and use padavan's RT56U

https://code.google.com/p/rt-n56u/


maxiscool
post Nov 6 2013, 08:27 PM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(Sharingan @ Nov 5 2013, 11:28 PM)
@asellus

Did u run successfully run Mikrotik with TM DHCP-PD ? Kinda wondering how's ur config looks like since i'm trying hard to follow the code and till now still return NULL . Well to be exact, i did get the address but i can't ping to ipv6.google.com nor www.kame.net .

My current setup:
Virtualbox 4.1.24
2 x Physical NIC
Mikrotik 5.25
ADSL 4M Streamyx

Few hours ago i did tried on pfSense 2.1-RELEASE , same condition met . Can't ping to both address at all and this time i'm quite sure that all my firewall rules are set for accept and forwarded properly. If else fails, i'll go back to tunnelbroker setup. Thanks for the attention and insights.
*
Hi @Sharingan ,

I'm facing the same issue whereby I'm not able to ping the domain name. However when tried with web browser, I'm able to surf the IPV6 domain.

Are you able to get thru this?

Thanks.
prasys
post Nov 6 2013, 08:27 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
For those who are using RT-56U

1. You need to flash to this 3rd party firmware. ASUS Firmware does support IPV6 for some reason it's super broke and it does not have radvd installed (which is needed to advertise to local computers) -> https://code.google.com/p/rt-n56u/

2. Once you have configured , go to IPV6 and set it up as follows

Do not bother off-loading to hardware for some reason it locks up. I think there might be a bug with the firmware I am using.

Just use get IP from both source , because one is from advertisement and other one is via DHCPv6. Not sure which one TM is using , so just put both


For DNSv6 , you can get the DNS servers automatically or use Google DNS Servers




Attached thumbnail(s)
Attached Image
Sharingan
post Nov 6 2013, 08:36 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


QUOTE(maxiscool @ Nov 6 2013, 08:27 PM)
Hi @Sharingan ,

I'm facing the same issue whereby I'm not able to ping the domain name. However when tried with web browser, I'm able to surf the IPV6 domain.

Are you able to get thru this?

Thanks.
*
@maxiscool

Hey there buddy, well i haven't figure it out yet since i'm quite confused as to @asellus config. In the statement that asellus pasted, i noticed that there's a bridge interface . Not sure on how to achieve this or what interface to bind/group with into the bridge. Will dig deeper later on since i'm quite handful with other task atm. I'm sure prasys or wkKay wouldn't mind shedding some light on this situation.

@asellus ,
Sorry for the late reply, i'm still figuring it out your full config atm and as i mentioned in this post, atm i'm kinda got my hands full with other tasks to complete. But if you wouldn't mind to shed some light on your full config please , it would really help us Mikrotik users here. Thanks .
yangchee98
post Nov 6 2013, 10:01 PM

Getting Started
**
Junior Member
264 posts

Joined: Dec 2010


Anyone here using tplink TL-WR1043ND router?
http://ipv6test.google.com/ says :
No problems detected.
You don’t have IPv6, but you shouldn’t have problems on websites that add IPv6 support.

Anyone using this router care to teach me how to enable ipv6 ?
asellus
post Nov 6 2013, 10:33 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 6 2013, 08:36 PM)
@maxiscool

Hey there buddy, well i haven't figure it out yet since i'm quite confused as to @asellus config. In the statement that asellus pasted, i noticed that there's a bridge interface . Not sure on how to achieve this or what interface to bind/group with into the bridge. Will dig deeper later on since i'm quite handful with other task atm. I'm sure prasys or wkKay wouldn't mind shedding some light on this situation.

@asellus ,
Sorry for the late reply, i'm still figuring it out your full config atm and as i mentioned in this post, atm i'm kinda got my hands full with other tasks to complete. But if you wouldn't mind to shed some light on your full config please , it would really help us Mikrotik users here. Thanks .
*
The rules are copy-pasta from http://www.mikrotik-routeros.com/2011/12/i...routeros-v5-10/
Basically it is the adaptation of the default IPv4 firewall rules in routerOS, with the exception that all ICMPv6 traffic and UDP traffic at port 546 are allowed.
It has a bridge interface because my Routerboard is a wireless router.
asellus
post Nov 6 2013, 10:38 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(yangchee98 @ Nov 6 2013, 10:01 PM)
Anyone here using tplink TL-WR1043ND router?
http://ipv6test.google.com/ says :
No problems detected.
You don’t have IPv6, but you shouldn’t have problems on websites that add IPv6 support.

Anyone using this router care to teach me how to enable ipv6 ?
*
I think the latest default firmware of that router does not support IPv6. You need third-party firmware like OpenWRT to make it support TM's IPv6 dual-stack service.

Attached Image

Barrier Breaker is the easiest although Attitude Adjustment is possible too. Beta Barrier breaker builds does not have a webgui though, therefore you have to be comfortable at using command-line.
andrew9292
post Nov 6 2013, 11:38 PM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


I cant seem to get IPv6 dns advertisments / address resolving properly from OpenWrt BB.

1. If enabling ONLY IPv6 in windows and flush the dns cache, I wont be able to resolve to ipv6 'text' addresses.
Eg... ping ipv6.google.com will fail. But ping 2404:6800:4001:800::1014 will pass.

2. If set custom IPv6 DNS into windows settings with ONLY IPv6 enabled, can resolve ipv6.google.com and it's native address format.

3. If turn on IPv6+IPv4, without inputing a custom ipv6 dns... able to resolve all addresses. So weird...

/etc/config/network
» Click to show Spoiler - click again to hide... «

/etc/config/6relayd
» Click to show Spoiler - click again to hide... «


Yet, resolv.conf.auto will show this, which means it was supposed to resolve! or not?
» Click to show Spoiler - click again to hide... «


For all i know that's all thats needed for ipv6 dns advertisment / resolving.
Do you guys face the same?
Any tips if any? Or is this just the nature of IPv6 at the moment? rclxub.gif

This post has been edited by andrew9292: Nov 7 2013, 12:08 AM
asellus
post Nov 7 2013, 12:01 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(andrew9292 @ Nov 6 2013, 11:38 PM)
I cant seem to get IPv6 dns advertisments / address resolving properly from OpenWrt BB.

1. If enabling ONLY IPv6 in windows and flush the dns cache, I wont be able to resolve to ipv6 addresses.
Eg... ping ipv6.google.com will fail. But ping 2404:6800:4001:800::1014 will pass.

2. If set custom IPv6 DNS with into windows settings ONLY IPv6 enabled, can resolve.

*
This is Windows' problem, not OpenWRT. Do not ever disable TCP/IP IPv4 stack in Windows, because Windows will ignore IPv6 DNS addresses sent by the router. Windows will always use the DNS server(s) provided by the DHCPv4 (not the RA) to get the AAAA records for IPv6-enabled domains. If you disable the IPv4 stack, you will not have any domain-resolving ability at all.

You have to use DHCPv6 server or use manual configuration in Windows (not feasible because TM gives out dynamic prefixes) if you really want to live with IPv6-only stack in Windows.
andrew9292
post Nov 7 2013, 12:06 AM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


QUOTE(asellus @ Nov 7 2013, 12:01 AM)
This is Windows' problem, not OpenWRT. Do not ever disable TCP/IP IPv4 stack in Windows, because Windows will ignore IPv6 DNS addresses sent by the router. Windows will always use the DNS server(s) provided by the DHCPv4 (not the RA) to get the AAAA records for IPv6-enabled domains. If you disable the IPv4 stack, you will not have any domain-resolving ability at all.

You have to use DHCPv6 server or use manual configuration in Windows (not feasible because TM gives out dynamic prefixes) if you really want to live with IPv6-only stack in Windows.
*
I see, that was my suspect too.
Dont intend to disable ipv4 but just wanted to test 'fully ipv6 only' and found this weird scenario...
I tried in OSX 10.6.8 too and it appeared simillar...
Thanks for the explaination! notworthy.gif
XeactorZ
post Nov 8 2013, 05:05 PM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
just got a called from tm staff
temporary solution for frequent disconnection my computer
my case is firmware version 1.06 TM, router is L7
solution is login router > go wireless setting > manual > untick enable auto channel scan > change wireless channel to ..... CH 13 for windows 7, CH 6 for windows xp, vista forget

This post has been edited by XeactorZ: Nov 8 2013, 05:05 PM
andrew9292
post Nov 8 2013, 08:32 PM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


QUOTE(XeactorZ @ Nov 8 2013, 05:05 PM)
just got a called from tm staff
temporary solution for frequent disconnection my computer
my case is firmware version 1.06 TM, router is L7
solution is login router > go wireless setting > manual > untick enable auto channel scan > change wireless channel to ..... CH 13 for windows 7, CH 6 for windows xp, vista forget
*
As far as i know, there is no such thing as 'best channel for this OS'
There are some routers which cannot run well on certain channels due to software or hardware designs. Example, my DIR-615-C2 has slightly weaker transmit power on channel 1 for some reason.

But this is whats real, taken from my previous postings:
Assuming the real cause of your problem is interference and poor config.
Part 1
» Click to show Spoiler - click again to hide... «


Part2
» Click to show Spoiler - click again to hide... «


This post has been edited by andrew9292: Nov 8 2013, 08:57 PM
UserU
post Nov 8 2013, 09:56 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

I followed the instructions for the DIR-615 router but after reboot(with a DC), it still stayed at IPv4. What gives?
XeactorZ
post Nov 9 2013, 01:28 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(andrew9292 @ Nov 8 2013, 08:32 PM)
As far as i know, there is no such thing as 'best channel for this OS'
There are some routers which cannot run well on certain channels due to software or hardware designs. Example, my DIR-615-C2 has slightly weaker transmit power on channel 1 for some reason.

But this is whats real, taken from my previous postings:
Assuming the real cause of your problem is interference and poor config.
Part 1
» Click to show Spoiler - click again to hide... «


Part2
» Click to show Spoiler - click again to hide... «

*
I didn't try case 1
but I already do the case 2, set the N only
and set to WPA2 and AES, channel width to 40 mhz
let see how it goes lolx

This post has been edited by XeactorZ: Nov 9 2013, 01:31 AM
Eoma
post Nov 9 2013, 01:02 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(yangchee98 @ Nov 6 2013, 10:01 PM)
Anyone here using tplink TL-WR1043ND router?
http://ipv6test.google.com/ says :
No problems detected.
You don’t have IPv6, but you shouldn’t have problems on websites that add IPv6 support.

Anyone using this router care to teach me how to enable ipv6 ?
*
With the current firmware available, it either goes v4 or v6. In the IPv6 section, there is anoter PPPoE dialog for you to login. If you have 2 valid logins, you can dial both v4 and v6 at the same time. The v6 is still terribly broken though.
Many emails to TP Link support but they are just "shaking legs/goyang kaki".
prasys
post Nov 9 2013, 02:42 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(UserU @ Nov 8 2013, 09:56 PM)
I followed the instructions for the DIR-615 router but after reboot(with a DC), it still stayed at IPv4. What gives?
*
What does windows ipconfig prints out for you


UserU
post Nov 10 2013, 01:47 AM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(prasys @ Nov 9 2013, 02:42 PM)
What does windows ipconfig prints out for you
*
Here's the image. I must have missed out something.
Attached Image


This post has been edited by UserU: Nov 10 2013, 01:50 AM
asellus
post Nov 10 2013, 07:54 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 10 2013, 01:47 AM)
Here's the image. I must have missed out something.
Attached Image
*
The image is really empty like that? If yes, with no link-local address, your TCP/IP stack has big problems.
UserU
post Nov 10 2013, 10:15 AM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 10 2013, 07:54 AM)
The image is really empty like that? If yes, with no link-local address, your TCP/IP stack has big problems.
*
Not empty actually, just censored out the IPs, that's all.

Checked the Local Area Connection Settings, IPv6 is not connected too.

This post has been edited by UserU: Nov 10 2013, 10:16 AM
asellus
post Nov 10 2013, 12:45 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 10 2013, 10:15 AM)
Not empty actually, just censored out the IPs, that's all.

Checked the Local Area Connection Settings, IPv6 is not connected too.
*
Just put the uncensored version here, nothing sensitive like MAC address is going to be shown there anyway.
UserU
post Nov 10 2013, 01:40 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 10 2013, 12:45 PM)
Just put the uncensored version here, nothing sensitive like MAC address is going to be shown there anyway.
*
Here are the images.
Attached Image
Attached Image
asellus
post Nov 10 2013, 04:11 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 10 2013, 01:40 PM)
Here are the images.
Attached Image
Attached Image
*
If that happens then either there are no IPv6 at all at your router, or that the router did not advertise the prefix on the network. Can you look at the webgui for the D-Link?
Wayne_DareDevil
post Nov 10 2013, 04:49 PM

New Member
*
Junior Member
31 posts

Joined: Sep 2012
From: 한국
Mind to ask, what's the major difference of using IPv4 and IPv6 ?
UserU
post Nov 10 2013, 04:57 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 10 2013, 04:11 PM)
If that happens then either there are no IPv6 at all at your router, or that the router did not advertise the prefix on the network. Can you look at the webgui for the D-Link?
*
I checked the DIR-615 dashboard, SETUP > IPv6 panel there:
[√] Enable IPv6 WAN Connection
My IPv6 connection is PPPoE, shared with IPv4.

However, I checked the STATUS > IPv6 on the dashboard and:
QUOTE
IPv6 Connection Type :    PPPoE
Network Status :    Disconnected
WAN IPv6 Address : 
IPv6 Default Gateway : 
Primary IPv6 DNS Server :    N/A
Secondary IPv6 DNS Server :    N/A


This post has been edited by UserU: Nov 10 2013, 05:00 PM
JohnLai
post Nov 10 2013, 05:00 PM

Skeptical Cat
*******
Senior Member
3,669 posts

Joined: Apr 2006
QUOTE(UserU @ Nov 10 2013, 04:57 PM)
I checked the DIR-615 dashboard, and it has the IPv6 panel there:
[√] Enable IPv6 WAN Connection
My IPv6 connection is PPPoE, shared with IPv4
*
Since I don't own DIR-615, I can't be sure on my advice.

Can you check if you have 'Enable RADVD' ticked? Somewhere at 'IPV6 Local Network'.

UserU
post Nov 10 2013, 05:03 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(JohnLai @ Nov 10 2013, 05:00 PM)
Since I don't own DIR-615, I can't be sure on my advice.

Can you check if you have 'Enable RADVD' ticked? Somewhere at 'IPV6 Local Network'.
*
Can't find that setting there... hmm.gif
asellus
post Nov 10 2013, 06:22 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 10 2013, 04:57 PM)
I checked the DIR-615 dashboard, SETUP > IPv6 panel there:
[√] Enable IPv6 WAN Connection
My IPv6 connection is PPPoE, shared with IPv4.

However, I checked the STATUS > IPv6 on the dashboard and:
*
If that's the case, then the router has not retrieved any prefix from TM. Is this UNIFI?
UserU
post Nov 10 2013, 08:48 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 10 2013, 06:22 PM)
If that's the case, then the router has not retrieved any prefix from TM. Is this UNIFI?
*
Yes, its UniFi.
asellus
post Nov 10 2013, 11:44 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 10 2013, 08:48 PM)
Yes, its UniFi.
*
Does the router run the latest firmware version?
yeam
post Nov 11 2013, 12:14 AM

New Member
*
Junior Member
16 posts

Joined: Dec 2005


I check with DIR615 1st before reflashed RTN56U.

After i upgraded the Unifi Router DIR615 to latest firmware. It become like this.
(Default 7.09 seem doesn't include IPv6 feature at all)

user posted image

user posted image

As usual i can ping from router.

ipv6.google.com -- router ping utilities return succeed.

All inhouse device still didn't pick up any IPv6 address.

***

TM full IPv6 support region related? roll out to everywhere? or maybe just certain place only?


Sharingan
post Nov 11 2013, 12:44 AM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

I seems to got the IPv6 part but sadly it's from HE.Net tunnelbroker. Will update here or via your PM about my findings tomorrow once i got back from work on TM IPv6.

Btw thanks, if this forum supports +1 or some sort of karma, you have my vote.
UserU
post Nov 11 2013, 02:04 AM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 10 2013, 11:44 PM)
Does the router run the latest firmware version?
*
Yep, its running on 7.17.
asellus
post Nov 11 2013, 06:05 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 11 2013, 02:04 AM)
Yep, its running on 7.17.
*
If that's the case, then your exchange probably haven't enabled IPv6 yet.
UserU
post Nov 11 2013, 01:40 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 11 2013, 06:05 AM)
If that's the case, then your exchange probably haven't enabled IPv6 yet.
*
So it means that this is only rolled out for Streamyx, and not UniFi yet?
prasys
post Nov 11 2013, 03:33 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
You are getting a blank for all ? No IPV4 nor 6 , wow your IP stack got some serious issues there
asellus
post Nov 11 2013, 04:10 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(UserU @ Nov 11 2013, 01:40 PM)
So it means that this is only rolled out for Streamyx, and not UniFi yet?
*
Some UNIFI users already has IPv6, maybe only at your exchange it did not happen yet.
UserU
post Nov 11 2013, 04:37 PM

CSONLINE2.NET - FREE COUNTER-STRIKE
Group Icon
Elite
5,093 posts

Joined: Mar 2009
From: Land of make believe

QUOTE(asellus @ Nov 11 2013, 04:10 PM)
Some UNIFI users already has IPv6, maybe only at your exchange it did not happen yet.
*
Oh well, a shame they still didn't release it in Subang yet hmm.gif
Sharingan
post Nov 11 2013, 05:11 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


Looks like i share the same fate as UserU, i got the address but it seems that my client cannot surf properly IPv6 sites. Even www.kame.net that turtle didn't dance for me.. sleep.gif . Right now i'm using HE.net tunnelbroker and it works like charm.. rules are default and RA is running fine inside Mikrotik (Virtualbox).
asellus
post Nov 11 2013, 11:26 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 11 2013, 05:11 PM)
Looks like i share the same fate as UserU, i got the address but it seems that my client cannot surf properly IPv6 sites. Even www.kame.net that turtle didn't dance for me.. sleep.gif . Right now i'm using HE.net tunnelbroker and it works like charm.. rules are default and RA is running fine inside Mikrotik (Virtualbox).
*
If you can pull a prefix from TM via DHCPv6-PD, there is no reason actually for your client to fail from using IPv6. If you emptied the '/ipv6 firewall' do you still have problems?
Sharingan
post Nov 12 2013, 12:15 AM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

In fact i did emptied it, i did test with HE.Net with emptied my firewall (IPv6 that is) and can get it working. So it's not the firewall rules i figured, something went beyond which i can reach atm. I'll look into it later after i got back from work.
asellus
post Nov 12 2013, 06:16 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 12 2013, 12:15 AM)
@asellus

In fact i did emptied it, i did test with HE.Net with emptied my firewall (IPv6 that is) and can get it working. So it's not the firewall rules i figured, something went beyond which i can reach atm. I'll look into it later after i got back from work.
*
Can you do successful ping from the routerOS to ipv6.google.com?
maxiscool
post Nov 12 2013, 07:35 AM

Casual
***
Junior Member
379 posts

Joined: Jan 2003
QUOTE(Sharingan @ Nov 6 2013, 08:36 PM)
@maxiscool

Hey there buddy, well i haven't figure it out yet since i'm quite confused as to @asellus config. In the statement that asellus pasted, i noticed that there's a bridge interface . Not sure on how to achieve this or what interface to bind/group with into the bridge. Will dig deeper later on since i'm quite handful with other task atm. I'm sure prasys or wkKay wouldn't mind shedding some light on this situation.

@asellus ,
Sorry for the late reply, i'm still figuring it out your full config atm and as i mentioned in this post, atm i'm kinda got my hands full with other tasks to complete. But if you wouldn't mind to shed some light on your full config please , it would really help us Mikrotik users here. Thanks .
*
@Sharingan
I just discovered that I've being ping the wrong way all this while to ping ipv6, apparently when I tried "ping6 ipv6.google.com" the return is positive. You may want to try this..

@asellus,
Am I doing it correctly? If yes, perhaps this will help others.
syahpian
post Nov 12 2013, 08:58 AM

Enthusiast
*****
Junior Member
811 posts

Joined: Jul 2008
From: Kota Kinabalu <-> Kuala Lumpur


~~edited~~

This post has been edited by syahpian: Nov 12 2013, 09:05 AM
darrenliew96
post Nov 12 2013, 09:03 AM

Getting Started
**
Junior Member
115 posts

Joined: Nov 2011


QUOTE(maxiscool @ Nov 12 2013, 07:35 AM)
@Sharingan
I just discovered that I've being ping the wrong way all this while to ping ipv6, apparently when I tried "ping6 ipv6.google.com" the return is positive. You may want to try this..

@asellus,
Am I doing it correctly? If yes, perhaps this will help others.
*
Yes... Linux and Unix user have separate ping.
It uses ping6 or traceroute6 for it's IPv6 connection
asellus
post Nov 12 2013, 10:41 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(maxiscool @ Nov 12 2013, 07:35 AM)
@Sharingan
I just discovered that I've being ping the wrong way all this while to ping ipv6, apparently when I tried "ping6 ipv6.google.com" the return is positive. You may want to try this..

@asellus,
Am I doing it correctly? If yes, perhaps this will help others.
*
'ping6' is used in Linux only. In routerOS, as of 6.6, 'ping' is still used.
Sharingan
post Nov 12 2013, 06:29 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

I've done some checking and i found that all of my IPv6 traffic went Unreplied after Syn Sent.

Mikrotik -> IPv6 -> Firewall -> Connection Tab

I even try ping from inside Mikrotik Terminal and here's the results:

CODE
[admin@MikroTik] > ping [:resolve ipv6.google.com]          
HOST                                     SIZE TTL TIME  STATUS                    
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2001:e68:4410:64a7::                      104  64 2ms   address unreachable      
   sent=4 received=0 packet-loss=100%

[admin@MikroTik] > ping 2001:200:dff:fff1:216:3eff:feb1:44d7
HOST                                     SIZE TTL TIME  STATUS                    
2001:200:dff:fff1:216:3eff:feb1:44d7                    timeout                  
2001:200:dff:fff1:216:3eff:feb1:44d7                    timeout                  
   sent=2 received=0 packet-loss=100%

[admin@MikroTik] > ping [:resolve ipv6.google.com]          
HOST                                     SIZE TTL TIME  STATUS                    
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
   sent=4 received=0 packet-loss=100%

[admin@MikroTik] >


Here's the info on Firewall -> Connection

CODE
[admin@MikroTik] /ipv6 firewall connection> print
Flags: S - seen reply, A - assured
#    PROTOCOL SRC-ADDRESS                 DST-ADDRESS                 TCP-STATE  
0 SA tcp      fe80::a02b:1dd9:d366:c5ef   fe80::a00:27ff:fe9d:aaa2    established
1    icmpv6   2001:e68:4410:64a7:35c2:... 2001:200:dff:fff1:216:3e...
2    tcp      2001:e68:4410:64a7:35c2:... 2404:6800:4001:c01::5f      syn-sent  
3    tcp      2001:e68:4410:64a7:35c2:... 2a02:26f0:8:181::eed        syn-sent  
4    tcp      2001:e68:4410:64a7:35c2:... 2401:3400:2000:1::17        syn-sent  
5    tcp      2001:e68:4410:64a7:35c2:... 2401:3400:2000:1::17        syn-sent  
6    tcp      2001:e68:4410:64a7:35c2:... 2a02:26f0:8:181::eed        syn-sent  
[admin@MikroTik] /ipv6 firewall connection> print
Flags: S - seen reply, A - assured
#    PROTOCOL SRC-ADDRESS                 DST-ADDRESS                 TCP-STATE  
0 SA tcp      fe80::a02b:1dd9:d366:c5ef   fe80::a00:27ff:fe9d:aaa2    established
1    icmpv6   2001:e68:4410:64a7:35c2:... 2001:200:dff:fff1:216:3e...
2    icmpv6   2001:e68:4410:64a7:35c2:... 2404:6800:4001:803::1012  
[admin@MikroTik] /ipv6 firewall connection>


As of the moment, here's my firewall IPv6 current rules

CODE
/ipv6 firewall filter
add action=accept chain=input comment="Router - Allow IPv6 ICMP" disabled=yes protocol=icmpv6
add action=accept chain=input comment="Router - Accept established connections" connection-state=established disabled=yes
add action=accept chain=input comment="Router - Accept related connections" connection-state=related disabled=yes
add action=drop chain=input comment="Router - Drop invalid connections" connection-state=invalid disabled=yes
add action=accept chain=input comment="Router- UDP" disabled=yes protocol=udp
add action=accept chain=input comment="Router - From our LAN" disabled=yes in-interface=ether1
add action=drop chain=input comment="Router - Drop other traffic" disabled=yes
add action=drop chain=forward comment="LAN - Drop invalid Connections" connection-state=invalid disabled=yes
add action=accept chain=forward comment="LAN - Accept UDP" disabled=no protocol=udp
add action=accept chain=forward comment="LAN - Accept ICMPv6 " disabled=yes protocol=icmpv6
add action=accept chain=forward comment="LAN - Accept established Connections" connection-state=established disabled=yes
add action=accept chain=forward comment="LAN - Accept related connections" connection-state=related disabled=yes
add action=accept chain=forward comment="LAN - Internal traffic" disabled=yes in-interface=ether1
add action=log chain=forward comment="LAN - Log everything else" disabled=yes log-prefix="Log IPv6"
add action=reject chain=forward comment="LAN - Drop everything else" connection-state=new disabled=yes in-interface=ether2 reject-with=icmp-no-route
add action=drop chain=input disabled=yes in-interface=sit1
add action=accept chain=forward disabled=yes protocol=icmpv6
add action=accept chain=forward connection-state=established disabled=yes
add action=accept chain=forward connection-state=related disabled=yes
add action=accept chain=forward disabled=yes
add action=accept chain=input connection-state=established disabled=yes
[admin@MikroTik] /ipv6 firewall>


And as you can see no rules are active and even if i active all or some of the rules, it still fails to ping or respond. DNS however responding though and correctly resolve name-> ipv6 .

My current setup,
Host OS: Windows 7 Ultimate 64
Virtualization: Virtualbox
Hardware : 2 Physical NIC (bridge setup both inside Virtualbox)
Software : Mikrotik 5.25

I can confirm that pfSense with HE.net Tunnelbroker setup works and all my LAN client can obtain address either via RA or DHCPv6. I can confirm also that Mikrotik with HE.Net tunnelbroker setup also works with/without firewall rules. Any comments from the forumers is much appreciated and please do not hesitate to ask for more information if needed.

p/s: Maybe it's not my time yet?

Regards


asellus
post Nov 12 2013, 10:38 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 12 2013, 06:29 PM)
@asellus

I've done some checking and i found that all of my IPv6 traffic went Unreplied after Syn Sent.

Mikrotik -> IPv6 -> Firewall -> Connection Tab

I even try ping from inside Mikrotik Terminal and here's the results:

CODE
[admin@MikroTik] > ping [:resolve ipv6.google.com]          
HOST                                     SIZE TTL TIME  STATUS                    
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2001:e68:4410:64a7::                      104  64 2ms   address unreachable      
   sent=4 received=0 packet-loss=100%

[admin@MikroTik] > ping 2001:200:dff:fff1:216:3eff:feb1:44d7
HOST                                     SIZE TTL TIME  STATUS                    
2001:200:dff:fff1:216:3eff:feb1:44d7                    timeout                  
2001:200:dff:fff1:216:3eff:feb1:44d7                    timeout                  
   sent=2 received=0 packet-loss=100%

[admin@MikroTik] > ping [:resolve ipv6.google.com]          
HOST                                     SIZE TTL TIME  STATUS                    
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
2404:6800:4001:803::1012                                timeout                  
   sent=4 received=0 packet-loss=100%

[admin@MikroTik] >


Here's the info on Firewall -> Connection

CODE
[admin@MikroTik] /ipv6 firewall connection> print
Flags: S - seen reply, A - assured
#    PROTOCOL SRC-ADDRESS                 DST-ADDRESS                 TCP-STATE  
0 SA tcp      fe80::a02b:1dd9:d366:c5ef   fe80::a00:27ff:fe9d:aaa2    established
1    icmpv6   2001:e68:4410:64a7:35c2:... 2001:200:dff:fff1:216:3e...
2    tcp      2001:e68:4410:64a7:35c2:... 2404:6800:4001:c01::5f      syn-sent  
3    tcp      2001:e68:4410:64a7:35c2:... 2a02:26f0:8:181::eed        syn-sent  
4    tcp      2001:e68:4410:64a7:35c2:... 2401:3400:2000:1::17        syn-sent  
5    tcp      2001:e68:4410:64a7:35c2:... 2401:3400:2000:1::17        syn-sent  
6    tcp      2001:e68:4410:64a7:35c2:... 2a02:26f0:8:181::eed        syn-sent  
[admin@MikroTik] /ipv6 firewall connection> print
Flags: S - seen reply, A - assured
#    PROTOCOL SRC-ADDRESS                 DST-ADDRESS                 TCP-STATE  
0 SA tcp      fe80::a02b:1dd9:d366:c5ef   fe80::a00:27ff:fe9d:aaa2    established
1    icmpv6   2001:e68:4410:64a7:35c2:... 2001:200:dff:fff1:216:3e...
2    icmpv6   2001:e68:4410:64a7:35c2:... 2404:6800:4001:803::1012  
[admin@MikroTik] /ipv6 firewall connection>


As of the moment, here's my firewall IPv6 current rules

CODE
/ipv6 firewall filter
add action=accept chain=input comment="Router - Allow IPv6 ICMP" disabled=yes protocol=icmpv6
add action=accept chain=input comment="Router - Accept established connections" connection-state=established disabled=yes
add action=accept chain=input comment="Router - Accept related connections" connection-state=related disabled=yes
add action=drop chain=input comment="Router - Drop invalid connections" connection-state=invalid disabled=yes
add action=accept chain=input comment="Router- UDP" disabled=yes protocol=udp
add action=accept chain=input comment="Router - From our LAN" disabled=yes in-interface=ether1
add action=drop chain=input comment="Router - Drop other traffic" disabled=yes
add action=drop chain=forward comment="LAN - Drop invalid Connections" connection-state=invalid disabled=yes
add action=accept chain=forward comment="LAN - Accept UDP" disabled=no protocol=udp
add action=accept chain=forward comment="LAN - Accept ICMPv6 " disabled=yes protocol=icmpv6
add action=accept chain=forward comment="LAN - Accept established Connections" connection-state=established disabled=yes
add action=accept chain=forward comment="LAN - Accept related connections" connection-state=related disabled=yes
add action=accept chain=forward comment="LAN - Internal traffic" disabled=yes in-interface=ether1
add action=log chain=forward comment="LAN - Log everything else" disabled=yes log-prefix="Log IPv6"
add action=reject chain=forward comment="LAN - Drop everything else" connection-state=new disabled=yes in-interface=ether2 reject-with=icmp-no-route
add action=drop chain=input disabled=yes in-interface=sit1
add action=accept chain=forward disabled=yes protocol=icmpv6
add action=accept chain=forward connection-state=established disabled=yes
add action=accept chain=forward connection-state=related disabled=yes
add action=accept chain=forward disabled=yes
add action=accept chain=input connection-state=established disabled=yes
[admin@MikroTik] /ipv6 firewall>


And as you can see no rules are active and even if i active all or some of the rules, it still fails to ping or respond. DNS however responding though and correctly resolve name-> ipv6 .

My current setup,
Host OS: Windows 7 Ultimate 64
Virtualization: Virtualbox
Hardware : 2 Physical NIC (bridge setup both inside Virtualbox)
Software : Mikrotik 5.25

I can confirm that pfSense with HE.net Tunnelbroker setup works and all my LAN client can obtain address either via RA or DHCPv6. I can confirm also that Mikrotik with HE.Net tunnelbroker setup also works with/without firewall rules. Any comments from the forumers is much appreciated and please do not hesitate to ask for more information if needed.

p/s: Maybe it's not my time yet?

Regards
*
What is the output of '/ipv6 route print'?

Sharingan
post Nov 16 2013, 02:03 AM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

Sorry for the late reply,

here's my output of /ipv6 route print


CODE
[admin@MikroTik] > ipv6 route print
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, o - ospf, b - bgp, U - unreachable
#      DST-ADDRESS              GATEWAY                  DISTANCE
0 ADS  ::/0                     Streamyx                        1
1  DS  ::/0                     fe80::121b:54ff:fe83:...        1
2 X S  ::/0                     2001:470:36:bd::1               1
3 X S  2000::/3                 2001:470:35:bd::1               1
4 X S  2000::/3                 ether2                          1
5 X S  2000::/3                 ether1                          1
6 ADC  2001:e68:4410:6d1f::/64  ether1                          0
[admin@MikroTik] >


The only active route is #6

asellus
post Nov 16 2013, 12:25 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 16 2013, 02:03 AM)
@asellus

Sorry for the late reply,

here's my output of /ipv6 route print
CODE
[admin@MikroTik] > ipv6 route print
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, o - ospf, b - bgp, U - unreachable
#      DST-ADDRESS              GATEWAY                  DISTANCE
0 ADS  ::/0                     Streamyx                        1
1  DS  ::/0                     fe80::121b:54ff:fe83:...        1
2 X S  ::/0                     2001:470:36:bd::1               1
3 X S  2000::/3                 2001:470:35:bd::1               1
4 X S  2000::/3                 ether2                          1
5 X S  2000::/3                 ether1                          1
6 ADC  2001:e68:4410:6d1f::/64  ether1                          0
[admin@MikroTik] >


The only active route is #6
*
ether1 is where your DHCP service runs?
ryan18
post Nov 16 2013, 03:46 PM

Look at all my stars!!
*******
Senior Member
2,406 posts

Joined: Jul 2010
From: bandar Sunway


anyone else having problem with unifi?in bandar sunway/subang jaya area?
Sharingan
post Nov 17 2013, 09:52 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus,

Yes ether1 is where the DHCP runs

ether1 = LAN NIC
ether2 = Streamyx NIC
asellus
post Nov 17 2013, 10:31 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 17 2013, 09:52 PM)
@asellus,

Yes ether1 is where the DHCP runs

ether1 = LAN NIC
ether2 = Streamyx NIC
*
There should be no problem then with your config; there is a link-local address in the PPPoE interface, and you got a /64 prefix too. Tw questions: Did the clients get IPv6 addresses via SLAAC from the router, and have you run radvd on ether1?
Sharingan
post Nov 17 2013, 10:50 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus ,

1. Client did received address via router (SLAAC)
2. radvd did listen on all interface
asellus
post Nov 17 2013, 10:55 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 17 2013, 10:50 PM)
@asellus ,

1. Client did received address via router (SLAAC)
2. radvd did listen on all interface
*
In radvd, did you set MTU to 1452?
Sharingan
post Nov 17 2013, 10:59 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


@asellus

No i didn't, but lemme try that and get back to you in a moment.
Sharingan
post Nov 17 2013, 11:02 PM

New Member
*
Junior Member
26 posts

Joined: Apr 2005


Well it's still the same results as earlier.
asellus
post Nov 17 2013, 11:48 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Sharingan @ Nov 17 2013, 11:02 PM)
Well it's still the same results as earlier.
*
Still cannot ping ipv6.google.com from the router itself, even with empty '/ipv6 firewall filter'? If that's the case somehow I think the parent OS of the VirtualBox may have something to do with it.
OKLY
post Nov 19 2013, 09:23 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


My long serving Buffalo WHR-HP-G300N on DD-WRT just died and so I reverted back to the stock DIR-615, really hassle free to enable IPv6 on this router. laugh.gif
OKLY
post Nov 19 2013, 10:52 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


wKkaY How come the forum does not show I have posted from an IPv6 address when I'm on my iPad?
TSwKkaY
post Nov 19 2013, 11:27 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(OKLY @ Nov 19 2013, 10:52 PM)
wKkaY How come the forum does not show I have posted from an IPv6 address when I'm on my iPad?
*
If your iPad isn't connecting to our forum over IPv6, then it won't show that you've posted from an IPv6 address.
OKLY
post Nov 20 2013, 09:49 AM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(wKkaY @ Nov 19 2013, 11:27 PM)
If your iPad isn't connecting to our forum over IPv6, then it won't show that you've posted from an IPv6 address.
*
Okay, after several testing, not sure why my iPad/iPhone is preferring IPv4 over IPv6 most of the time. My desktop PC has no issues. sweat.gif

Guys, anyone tried TP-Link TL-WDR4300? Does it fully support IPv6? Thinking of getting this to replace my previous Buffalo WHR-HP-G300N as I'm now on the stock D-Link DIR-615.
yeam
post Nov 20 2013, 11:30 AM

New Member
*
Junior Member
16 posts

Joined: Dec 2005


Probably because of this.
http://en.wikipedia.org/wiki/Happy_Eyeballs
Eoma
post Nov 20 2013, 04:57 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(OKLY @ Nov 20 2013, 09:49 AM)
Guys, anyone tried TP-Link TL-WDR4300? Does it fully support IPv6? Thinking of getting this to replace my previous Buffalo WHR-HP-G300N as I'm now on the stock D-Link DIR-615.
*
Stay away. It still doesn't have Dual Stack support.
OKLY
post Nov 20 2013, 08:42 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(Eoma @ Nov 20 2013, 04:57 PM)
Stay away. It still doesn't have Dual Stack support.
*
Thanks, guess I have to stick with the stock DIR-615 first for now while the other manufacturers sort out their firmware to fully support IPv6.
iOnicStorm
post Nov 20 2013, 11:11 PM

New Member
*
Junior Member
18 posts

Joined: Nov 2008
From: Malaysia


QUOTE(OKLY @ Nov 20 2013, 09:49 AM)
Guys, anyone tried TP-Link TL-WDR4300? Does it fully support IPv6? Thinking of getting this to replace my previous Buffalo WHR-HP-G300N as I'm now on the stock D-Link DIR-615.
*
TP-Link's stock firmware may not have good support for ipv6, but WDR4300 is well supported by OpenWRT and it's Linux!

http://wiki.openwrt.org/toh/tp-link/tl-wdr4300
http://ofmodemsandmen.com/supported.html

OKLY
post Nov 20 2013, 11:51 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(iOnicStorm @ Nov 20 2013, 11:11 PM)
TP-Link's stock firmware may not have good support for ipv6, but WDR4300 is well supported by OpenWRT and it's Linux!

http://wiki.openwrt.org/toh/tp-link/tl-wdr4300
http://ofmodemsandmen.com/supported.html
*
Will look into that but currently prefer something that will work out of the box.
Moogle Stiltzkin
post Nov 21 2013, 12:08 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:45 AM
hellzboyz
post Nov 21 2013, 12:55 PM

New Member
*
Junior Member
8 posts

Joined: Jun 2012


IPv6 available for Unifi area Shah Alam? I using Unifi BIZ20.
Router D-Link DL-604 Firmware 7.15.

IPv6 Connection status : Disconnect.
IPv6 Connection Type: PPPoE

Any help?
Moogle Stiltzkin
post Nov 21 2013, 03:15 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:45 AM
piju
post Nov 21 2013, 05:39 PM

Getting Started
**
Junior Member
164 posts

Joined: Feb 2008
guys,

i cant tick dual lan checkbox box but i can tick ipv6 checkbox on L7 router. location is in sungai buloh. is there any chance that sungai buloh area is not ipv6 supported yet ?
Moogle Stiltzkin
post Nov 21 2013, 07:56 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:46 AM
OKLY
post Nov 22 2013, 12:25 AM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(Moogle Stiltzkin @ Nov 21 2013, 03:15 PM)
same issue here  hmm.gif  how to fix ?
*
Try lowering the MTU value to 1452.
Moogle Stiltzkin
post Nov 22 2013, 06:23 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:46 AM
prasys
post Nov 22 2013, 11:46 AM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(Moogle Stiltzkin @ Nov 21 2013, 12:08 PM)
i confirm got ipv6

but i'm not sure how to set up properly.
1. do i switch to opendns ipv6 ? or continue using tmnuts default dns ?
2. how to set chrome and firefox to prefer ipv6 when available ? Currently they prefer ipv4 :/
3. any other settings to do ?
4. does diablo 3 have ipv6 ? how to ping test to their server ?
*
1. I switched to Google's
2. It will automatically prefer IPV6 whenever posisble. Need to clear DNS cache and try lowyat.net , it will use ipv6
3. No
4. Yes , for World of Warcraft. Not sure about Diablo 3 . I assume it will work for it. http://ipv6.blizzard.com/
Alpha_Tay
post Nov 22 2013, 01:15 PM

Beware The Spammer Star!
******
Senior Member
1,725 posts

Joined: Jan 2003
speedtest.net support ipv6? ipv6 ping should be higher than ipv4 most if not all of the times.

QUOTE(Moogle Stiltzkin @ Nov 21 2013, 07:56 PM)
user posted image

tested using Unifi IPV6  flex.gif
Now for the real test for internetional connection.
user posted image

user posted image

user posted image

user posted image

user posted image

wub.gif
As a gamer, from my observation, the 200-300ms is pretty okay for gaming overseas. This is a vast improvement from long ago during the adsl times when ping latency was somewhere around 600-800ms and even more on bad days.

Local gaming say counter strike with 4-15 ms .....is just insanely good..... almost as fast latency as playing on a lan  laugh.gif
Anyway, just some observations.

I noticed my laptop shows in the ipv6 test as having it, but my desktop didn't. To fix that, i went to my network adapter and disabled it, and turn it back on after 10 seconds. As an extra measure i also went to cmd and did a ipconfig /flushdns

I then refresh the browser to perform the test, and it accurately showed that i'm running on ipv6.

Oh and i notice that the test indicated that the browser will prefer ipv4 over ipv6 when both are available. I'm not quite sure how to prioritize ipv6  hmm.gif

also i'm having trouble accessing facebook. not quite sure how to fix that.
*
Moogle Stiltzkin
post Nov 22 2013, 01:24 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:46 AM
Moogle Stiltzkin
post Nov 22 2013, 07:41 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:46 AM
Moogle Stiltzkin
post Nov 23 2013, 12:02 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:46 AM
wkkm007
post Nov 23 2013, 03:28 PM

Look at all my stars!!
*******
Senior Member
3,123 posts

Joined: Sep 2008
From: OUG - Muhibbah LRT


Can't get IPv6, Unifi VIP5 Ampang
L7 modem

PDF doc from TMnet about enabling IPv6

For Dynamic IP I can't tick ''Dual LAN'' cry.gif , but can tick ''Enable IPv6''
For Fixed IP I can't access the internet but can tick both ''Dual LAN'' and ''Enable IPv6''

Is that for Unifi VIP5 user can't use Fixed IP? Must use Dynamic IP hmm.gif

ipv6.pcap.zip
what is this?

This post has been edited by wkkm007: Nov 23 2013, 03:38 PM
SUSmrlive005
post Nov 23 2013, 05:21 PM

Getting Started
**
Junior Member
114 posts

Joined: Nov 2013
Did my IPV6 enable yet ?
user posted image

What i should configure here ? it say i still on ipv4 and ipv6 no internet access as u can see in the image, appreciate any help .
user posted image

This post has been edited by mrlive005: Nov 23 2013, 05:23 PM
jolmy
post Nov 23 2013, 05:31 PM

Meow
******
Senior Member
1,182 posts

Joined: Jan 2003


QUOTE(iOnicStorm @ Nov 20 2013, 11:11 PM)
TP-Link's stock firmware may not have good support for ipv6, but WDR4300 is well supported by OpenWRT and it's Linux!

http://wiki.openwrt.org/toh/tp-link/tl-wdr4300
http://ofmodemsandmen.com/supported.html
*
QUOTE(OKLY @ Nov 20 2013, 11:51 PM)
Will look into that but currently prefer something that will work out of the box.
*
Unfortunately, the firmware that supports TM UniFi at the moment does not have IPv6 support, although the general firmware does. Just hope TP-Link can release an updated firmware soon that supports IPv6 on TM UniFi.
SUSmrlive005
post Nov 23 2013, 06:27 PM

Getting Started
**
Junior Member
114 posts

Joined: Nov 2013
Now it's enable, but i still can't test http://ipv6-test.com/ , something wrong.
Image
user posted image

This is my result when i do test
user posted image

This post has been edited by mrlive005: Nov 23 2013, 06:27 PM
asellus
post Nov 23 2013, 08:23 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(mrlive005 @ Nov 23 2013, 06:27 PM)
Now it's enable, but i still can't test http://ipv6-test.com/ , something wrong.
Image
» Click to show Spoiler - click again to hide... «


This is my result when i do test
» Click to show Spoiler - click again to hide... «

*
Try this test page first, then try opening this IPv6-only page if it loads or not.
SUSmrlive005
post Nov 23 2013, 10:12 PM

Getting Started
**
Junior Member
114 posts

Joined: Nov 2013
QUOTE(asellus @ Nov 23 2013, 08:23 PM)
Try this test page first, then try opening this IPv6-only page if it loads or not.
*
i guess it's enable lol tongue.gif i can open both of them.

Can anyone please explain me ? what is the differences Ipv4 and Ipv6 ?
is it will make my internet more speed ? would i have lower ping when i play game ?
Sorry i dont have time to read all those 22 page ;/ i'm just a basic computer user .
Thx in advance



user posted image
OKLY
post Nov 23 2013, 10:27 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(mrlive005 @ Nov 23 2013, 10:12 PM)
i guess it's enable lol tongue.gif i can open both of them.

Can anyone please explain me ? what is the differences Ipv4 and Ipv6  ?
is it will make my internet more speed ? would i have lower ping when i play game ?
Sorry i dont have time to read all those 22 page ;/ i'm just a basic computer user .
Thx in advance
user posted image
*
Yes, if you're connected to this forum via IPv6 then you will see the IPv6 word next to your post number. smile.gif
SUSmrlive005
post Nov 23 2013, 10:34 PM

Getting Started
**
Junior Member
114 posts

Joined: Nov 2013
QUOTE(OKLY @ Nov 23 2013, 10:27 PM)
Yes, if you're connected to this forum via IPv6 then you will see the IPv6 word next to your post number. smile.gif
*
Oh ye, i see it tongue.gif
can you explain what is the differences btw ipv4 and ipv6 ? would it make my ping lower when i play game and speed up my connection?

This post has been edited by mrlive005: Nov 23 2013, 10:36 PM
OKLY
post Nov 23 2013, 10:45 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(wKkaY @ Nov 19 2013, 11:27 PM)
If your iPad isn't connecting to our forum over IPv6, then it won't show that you've posted from an IPv6 address.
*
QUOTE(yeam @ Nov 20 2013, 11:30 AM)
Yup I think it's due to Happy Eyeballs.

Attached Image

Connecting to this forum using IPv6 will result in slightly higher ping compared to IPv4 and I think that's why my iPad/iPhone resorted back to IPv4. hmm.gif
OKLY
post Nov 23 2013, 10:51 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(mrlive005 @ Nov 23 2013, 10:34 PM)
Oh ye, i see it tongue.gif
can you explain what is the differences btw ipv4 and ipv6 ? would it make my ping lower when i play game and speed up my connection?
*
In a not so technical way of explaining, most of the time they will perform about the same. The difference won't make miracles happen (e.g. from lag to no lag).
Anonymous34
post Nov 24 2013, 04:38 PM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(OKLY @ Nov 23 2013, 10:51 PM)
In a not so technical way of explaining, most of the time they will perform about the same. The difference won't make miracles happen (e.g. from lag to no lag).
*
I thought they said ipv4 is very congested so that's why they invented iPv6 for more space. Btw bro I have just tukar my dir 615 to Asus RT-N10+ C1 with openwrt. Everything works except iptv. Any idea how to set up ipv6?
I'm really noob in networking things.
OKLY
post Nov 24 2013, 08:48 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(amirsubhi @ Oct 7 2013, 06:22 PM)
Tested my Asus RT-N12 C1 Ver 3.0.0.4.374_813 with Unifi

and IPv6 connected  rclxm9.gif

» Click to show Spoiler - click again to hide... «

*
Do you mind sharing your WAN and IPv6 settings? My IPv6 is fine but I can't seem to get 10/10 from the IPv6 test as the site is reporting that I may have MTU problems. hmm.gif
Anonymous34
post Nov 24 2013, 08:57 PM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(OKLY @ Nov 24 2013, 08:48 PM)
Do you mind sharing your WAN and IPv6 settings? My IPv6 is fine but I can't seem to get 10/10 from the IPv6 test as the site is reporting that I may have MTU problems. hmm.gif
*
I also want to know how to configure ipv6 on open-wrt firmware nod.gif
Please someone teach us! After configure also cannot work.
OKLY
post Nov 24 2013, 09:08 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(Anonymous34 @ Nov 24 2013, 08:57 PM)
I also want to know how to configure ipv6 on open-wrt firmware nod.gif
Please someone teach us! After configure also cannot work.
*
This one need OpenWRT guru, I'm on Asus' stock firmware only.
andrew9292
post Nov 24 2013, 09:17 PM

-/Livin' On A Prayer/-
*****
Senior Member
955 posts

Joined: Sep 2008
From: Petaling Jaya


QUOTE(Anonymous34 @ Nov 24 2013, 04:38 PM)
I thought they said ipv4 is very congested so that's why they invented iPv6 for more space. Btw bro I have just tukar my dir 615 to Asus RT-N10+ C1 with openwrt. Everything works except iptv. Any idea how to set up ipv6?
I'm really noob in networking things.
*
They just ran out of addresses. Just like number plates.

WYZ 1234 = v4
W 1234 A = v6

Route still the same or assigned by isp peering.
It means that even if u hav ipv6 'number plate'. If your isp assigns a 'kampung road' to your address, it wont be any faster. If u get a fast route, faster. Simillar route, same speed.

Old number plate or new number plate, both on the same existing roads.
Ipv4 or ipv6. Same theory.
At the end of the day, just a number plate to identify yourself.lol.

If there's any speed difference, it will be due to specific peering to that ip subnet by isp, which happens to be a faster or slower route.

Correct me if im wrong.
----

For ipv6 on Openwrt i only got it to work on latest beta 'barrier breaker'. It has native ipv6 support
Settings have to be done via ssh as the build is too big to install luci. Follow their wiki, pretty straightforward.
http://wiki.openwrt.org/doc/uci/network6#b...eaker.and.later

This post has been edited by andrew9292: Nov 24 2013, 09:28 PM
OKLY
post Nov 24 2013, 09:18 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(andrew9292 @ Nov 24 2013, 09:17 PM)
They just ran out of addresses. Just like number plates.

WYZ 1234 = v4
W 1234 A = v6

Route still the same or assigned by isp peering.
It means that even if u hav ipv6 'number plate'. If your isp assigns a 'kampung road' to your address, it wont be any faster. If u get a fast route, faster. Simillar route, same speed.

Old number plate or new number plate, both on the same road.
Ipv4 or ipv6. Same theory. At the end of the day, just a number plate.lol.

Correct me if im wrong
*
Yes, one should not expect too much of performance. It won't make miracles happen.
prasys
post Nov 24 2013, 09:37 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
QUOTE(mrlive005 @ Nov 23 2013, 10:34 PM)
Oh ye, i see it tongue.gif
can you explain what is the differences btw ipv4 and ipv6 ? would it make my ping lower when i play game and speed up my connection?
*
In my case , World of Warcraft ping times have been reduced by 30-40ms.

There are some cases whereby the ping time increased

Again , your game server ,game client must support IPV6. So far World of Warcraft supports IPV6 , not sure if other MMO games support IPV6 or any other games


On IPV6 , there are some routes faster compared to IPV4. Again there are cases where it is worst

Performance may vary


patienceGNR
post Nov 24 2013, 10:00 PM

♥ Ride All Day ♥
*******
Senior Member
2,058 posts

Joined: Mar 2011
From: Today: 9:03 AM



Anybody having wonky internet now? My Modem keeps restarting by itself. Sigh.

OKLY
post Nov 24 2013, 10:03 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(patienceGNR @ Nov 24 2013, 10:00 PM)
Anybody having wonky internet now? My Modem keeps restarting by itself. Sigh.
*
Nope mine is fine, if your modem is restarting by itself then that should be a hardware issue already.
patienceGNR
post Nov 24 2013, 10:05 PM

♥ Ride All Day ♥
*******
Senior Member
2,058 posts

Joined: Mar 2011
From: Today: 9:03 AM



QUOTE(OKLY @ Nov 24 2013, 10:03 PM)
Nope mine is fine, if your modem is restarting by itself then that should be a hardware issue already.
*
it was working fine earlier today. hmm.gif crap......... and it keeps restarting every 2 minutes now. only Power will be on, then slowly all others reconnect.

I think I have made 5 calls to UniFi center, with 2 calls that went through but disconnected halfway - and then no one calls back. Terus create a case and close it.

How I know it is closed - I received SMS saying it is closed. Seriously? In Starhub where I work, if the agents close the case without giving call back, will kena one.
Moogle Stiltzkin
post Nov 24 2013, 10:47 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:47 AM
patienceGNR
post Nov 24 2013, 11:17 PM

♥ Ride All Day ♥
*******
Senior Member
2,058 posts

Joined: Mar 2011
From: Today: 9:03 AM



QUOTE(Moogle Stiltzkin @ Nov 24 2013, 10:47 PM)
welcome to monopoly or as we say, malaysia boleh  laugh.gif
*
Just ended a 21min long call with them, using my hp. gonna cost me a bomb. will definitely seek compensation dy. 1-3mths waiver whistling.gif

my typical learned-from-Singaporean style whistling.gif service down, terus marah. hahahaha. well, they can't pinpoint what the issue is, no wrong to that but they require 24hrs for tech to reply to the case first, then only will send tech to my house here to check on the hub. that'll take another like 24 hours? i on the call said, "The very least for them to come to my house is by Tuesday. So I gotta bear with the internet that disconnects every 2-5 minutes for 2 days? I will definitely seek for compensation in this case. I would want to hear from TM regarding my case tomorrow. No calls tomorrow from TM, I will call in and look for your manager."

diam je the agent. i know not her fault but she cannot give resolution, like, "Ok sir, I will send out an e-mail to the technical team, the very least I could do to assist to resolve your issue as you require the internet."

at least saying that can psychologically tipu orang. just my experience working in call centers lah tongue.gif but we do send out emails to speed up process.

well, just sharing my experience to people who, in future, want to dispute/complaint/get waiver.
OKLY
post Nov 24 2013, 11:28 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(patienceGNR @ Nov 24 2013, 11:17 PM)
Just ended a 21min long call with them, using my hp. gonna cost me a bomb. will definitely seek compensation dy. 1-3mths waiver whistling.gif

my typical learned-from-Singaporean style whistling.gif service down, terus marah. hahahaha. well, they can't pinpoint what the issue is, no wrong to that but they require 24hrs for tech to reply to the case first, then only will send tech to my house here to check on the hub. that'll take another like 24 hours? i on the call said, "The very least for them to come to my house is by Tuesday. So I gotta bear with the internet that disconnects every 2-5 minutes for 2 days? I will definitely seek for compensation in this case. I would want to hear from TM regarding my case tomorrow. No calls tomorrow from TM, I will call in and look for your manager."

diam je the agent. i know not her fault but she cannot give resolution, like, "Ok sir, I will send out an e-mail to the technical team, the very least I could do to assist to resolve your issue as you require the internet."

at least saying that can psychologically tipu orang. just my experience working in call centers lah tongue.gif but we do send out emails to speed up process.

well, just sharing my experience to people who, in future, want to dispute/complaint/get waiver.
*
One annoying thing is they do not have a toll free or at least free for their own customers to call. Time is already ticking the moment we have to press this and that and wait for the call to be connected to a customer service personnel. sweat.gif
alexwsk
post Nov 24 2013, 11:30 PM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


QUOTE(andrew9292 @ Nov 24 2013, 09:17 PM)
They just ran out of addresses. Just like number plates.
For ipv6 on Openwrt i only got it to work on latest beta 'barrier breaker'. It has native ipv6 support
Settings have to be done via ssh as the build is too big to install luci. Follow their wiki, pretty straightforward.
http://wiki.openwrt.org/doc/uci/network6#b...eaker.and.later
*
for barrier breaker, need to Enable IPv6 negotiation on the PPP link?
And which protocol to select for WAN6?
thx

This post has been edited by alexwsk: Nov 24 2013, 11:34 PM
asellus
post Nov 24 2013, 11:41 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(alexwsk @ Nov 24 2013, 11:30 PM)
for barrier breaker, need to Enable IPv6 negotiation on the PPP link?
And which protocol to select for WAN6?
thx
*
You need to create a DHCPv6-PD client on your @wan interface too.
patienceGNR
post Nov 24 2013, 11:46 PM

♥ Ride All Day ♥
*******
Senior Member
2,058 posts

Joined: Mar 2011
From: Today: 9:03 AM



QUOTE(OKLY @ Nov 24 2013, 11:28 PM)
One annoying thing is they do not have a toll free or at least free for their own customers to call. Time is already ticking the moment we have to press this and that and wait for the call to be connected to a customer service personnel.  sweat.gif
*
It is free if you're calling from their own number, i.e your houseline but if your Unifi is down, how to call la? laugh.gif

Really funny one these people laugh.gif
alexwsk
post Nov 25 2013, 12:01 AM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


QUOTE(asellus @ Nov 24 2013, 11:41 PM)
You need to create a DHCPv6-PD client on your @wan interface too.
*
any details guide? currently i have luci but have not install luci-proto-ipv6
can I do it manually by modifying /etc/config/network only or need to modify more files?
asellus
post Nov 25 2013, 05:50 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(alexwsk @ Nov 25 2013, 12:01 AM)
any details guide? currently i have luci but have not install luci-proto-ipv6
can I do it manually by modifying /etc/config/network only or need to modify more files?
*
With Barrier Breaker, only need to modify '/etc/config/network' file, if you don't install luci-proto-ipv6. Still need odhcp6c though.

This post has been edited by asellus: Nov 25 2013, 05:52 AM
SUSmrlive005
post Nov 25 2013, 06:33 AM

Getting Started
**
Junior Member
114 posts

Joined: Nov 2013
Do you guys running on both ? btw Ipv4 and Ipv6 ? im not sure if im doing the right things, just clear me up tongue.gif or i should disable one of them ?

user posted image

This post has been edited by mrlive005: Nov 25 2013, 06:34 AM
asellus
post Nov 25 2013, 06:48 AM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(mrlive005 @ Nov 25 2013, 06:33 AM)
Do you guys running on both ? btw Ipv4 and Ipv6 ? im not sure if im doing the right things, just clear me up tongue.gif or i should disable one of them ?

» Click to show Spoiler - click again to hide... «

*
Of course you should run both, many sites are still IPv4-only.
Anonymous34
post Nov 25 2013, 10:45 AM

Look at all my stars!!
*******
Senior Member
3,176 posts

Joined: May 2013
From: Petaling Jaya


QUOTE(andrew9292 @ Nov 24 2013, 09:17 PM)
They just ran out of addresses. Just like number plates.

WYZ 1234 = v4
W 1234 A = v6

Route still the same or assigned by isp peering.
It means that even if u hav ipv6 'number plate'. If your isp assigns a 'kampung road' to your address, it wont be any faster. If u get a fast route, faster. Simillar route, same speed.

Old number plate or new number plate, both on the same existing roads.
Ipv4 or ipv6. Same theory.
At the end of the day, just a number plate to identify yourself.lol.

If there's any speed difference, it will be due to specific peering to that ip subnet by isp, which happens to be a faster or slower route.

Correct me if im wrong.
----

For ipv6 on Openwrt i only got it to work on latest beta 'barrier breaker'. It has native ipv6 support
Settings have to be done via ssh as the build is too big to install luci. Follow their wiki, pretty straightforward.
http://wiki.openwrt.org/doc/uci/network6#b...eaker.and.later
*
Mind explaining to me more detailing? I'm sorry I'm a noob in networking sad.gif
If you help me this time I could help you with your computer next time! biggrin.gif
PS:I have no idea how to install Barrier breaker

This post has been edited by Anonymous34: Nov 25 2013, 10:46 AM
alexwsk
post Nov 25 2013, 11:29 AM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


QUOTE(asellus @ Nov 25 2013, 05:50 AM)
With Barrier Breaker, only need to modify '/etc/config/network' file, if you don't install luci-proto-ipv6. Still need odhcp6c though.
*
odhcp6c has been installed by default
can you post or pm me your /etc/config/network without those sensitive info, thx notworthy.gif
Moogle Stiltzkin
post Nov 25 2013, 12:19 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:47 AM
asellus
post Nov 25 2013, 12:46 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(alexwsk @ Nov 25 2013, 11:29 AM)
odhcp6c has been installed by default
can you post or pm me your /etc/config/network without those sensitive info, thx  notworthy.gif
*
I don't have the router anymore, but just doing what http://wiki.openwrt.org/doc/uci/network6 told you and you should be OK.

CODE

config interface wan
       option ipv6 1 # only required for PPP-based protocols
       ...

config interface wan6
       option ifname   @wan
       option proto    dhcpv6

config interface lan
       option proto    static
       option ip6assign 60
       ...

alexwsk
post Nov 25 2013, 03:28 PM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


QUOTE(asellus @ Nov 25 2013, 12:46 PM)
I don't have the router anymore, but just doing what http://wiki.openwrt.org/doc/uci/network6 told you and you should be OK.

CODE

config interface wan
       option ipv6 1 # only required for PPP-based protocols
       ...

config interface wan6
       option ifname   @wan
       option proto    dhcpv6

config interface lan
       option proto    static
       option ip6assign 60
       ...

*
ok, thx
will try it out, currently one location no ipv6 yet (USJ), will try at another location (PJ)
asellus
post Nov 25 2013, 04:29 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(alexwsk @ Nov 25 2013, 03:28 PM)
ok, thx
will try it out, currently one location no ipv6 yet (USJ), will try at another location (PJ)
*
BTW, the 'option ip6assign' for Streamyx should be 64.
alexwsk
post Nov 25 2013, 11:50 PM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


QUOTE(asellus @ Nov 25 2013, 04:29 PM)
BTW, the 'option ip6assign' for Streamyx should be 64.
*
mine are unifi/unifibiz
no luck at both areas
XeactorZ
post Nov 26 2013, 01:12 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
QUOTE(mrlive005 @ Nov 25 2013, 06:33 AM)
Do you guys running on both ? btw Ipv4 and Ipv6 ? im not sure if im doing the right things, just clear me up tongue.gif or i should disable one of them ?

user posted image
*
yup running both
XeactorZ
post Nov 26 2013, 01:18 AM

♥ PandaDog ♥
*********
All Stars
31,607 posts

Joined: Aug 2010
btw how to enable ipv6 for google chrome ?
try below link solution, don't have the button at all
http://www.upubuntu.com/2012/06/how-to-ena...-in-google.html

only showing Default address family: UNSPECIFIED

fizal hashim
post Nov 26 2013, 01:13 PM

New Member
*
Newbie
1 posts

Joined: Nov 2013


hello fella's,

why i cannot set ipv6 at my laptop and my router too?
im using unifi vip 5 and my laptop is using windows 7 pro.
as my router L7.

1.cannot tick at dual lan
Moogle Stiltzkin
post Nov 26 2013, 01:31 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:47 AM
OKLY
post Nov 27 2013, 11:01 PM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


QUOTE(fizal hashim @ Nov 26 2013, 01:13 PM)
hello fella's,

why i cannot set ipv6 at my laptop and my router too?
im using unifi vip 5 and my laptop is using windows 7 pro.
as my router L7.

1.cannot tick at dual lan
*
When you say cannot set, are your devices not getting any IPv6 addresses from the router? Perhaps some supporting screenshots of your router configuration page would help.
alexwsk
post Nov 28 2013, 11:46 AM

Look at all my stars!!
*******
Senior Member
4,090 posts

Joined: Jan 2003
From: USJ


seems like PJ seksyen 17 got ipv6
just testing out with this post

/etc/config/network for openwrt barrier breaker as below:

config interface 'wan'
option ifname 'eth0.500'
option proto 'pppoe'
option username 'xxxxxx@unifi'
option password 'xxxxxx'
option peerdns '0'
option dns '8.8.8.8 208.67.222.222'
option ipv6 '1'

config interface 'wan6'
option ifname '@wan'
option proto 'dhcpv6'
option reqaddress 'try'
option reqprefix 'auto'
option peerdns '0'
option dns '2001:4860:4860::8888 2620:0:ccc::2'

This post has been edited by alexwsk: Nov 28 2013, 11:55 AM
TSwKkaY
post Nov 28 2013, 04:24 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Just went for a presentation by TM on their IPv6 broadband rollout.

A few new things I learned today:

1) Dual-stacking IPv4/IPv6 increases resource usage at the BRAS (memory, licensing, etc). This is one of the factors that limit the rollout.

2) Business broadband (static IP) customers need to call their account manager or branch to request for an IPv6 prefix. It isn't assigned automatically like for home users.

3) The hotline staff are trained in IPv6 hmm.gif
aneip
post Nov 28 2013, 04:43 PM

Look at all my stars!!
*******
Senior Member
2,466 posts

Joined: Nov 2004


QUOTE(wKkaY @ Nov 28 2013, 04:24 PM)
Just went for a presentation by TM on their IPv6 broadband rollout.

A few new things I learned today:

1) Dual-stacking IPv4/IPv6 increases resource usage at the BRAS (memory, licensing, etc). This is one of the factors that limit the rollout.

2) Business broadband (static IP) customers need to call their account manager or branch to request for an IPv6 prefix. It isn't assigned automatically like for home users.

3) The hotline staff are trained in IPv6 hmm.gif
*
All place roll out already?
asellus
post Nov 28 2013, 05:34 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(wKkaY @ Nov 28 2013, 04:24 PM)
Just went for a presentation by TM on their IPv6 broadband rollout.

A few new things I learned today:

1) Dual-stacking IPv4/IPv6 increases resource usage at the BRAS (memory, licensing, etc). This is one of the factors that limit the rollout.

2) Business broadband (static IP) customers need to call their account manager or branch to request for an IPv6 prefix. It isn't assigned automatically like for home users.

3) The hotline staff are trained in IPv6 hmm.gif
*
you didn;t ask if TM will give out prefix larger than /64?
rogue
post Nov 28 2013, 05:54 PM

Getting Started
**
Junior Member
75 posts

Joined: Jun 2006
QUOTE(asellus @ Nov 28 2013, 05:34 PM)
you didn;t ask if TM will give out prefix larger than /64?
*
Unless you are running as an SLA, I doubt it.
TSwKkaY
post Nov 28 2013, 06:07 PM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
Edit: I'll email her your questions.

This post has been edited by wKkaY: Nov 28 2013, 06:56 PM
Moogle Stiltzkin
post Nov 28 2013, 06:10 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:47 AM
rogue
post Nov 28 2013, 06:59 PM

Getting Started
**
Junior Member
75 posts

Joined: Jun 2006
QUOTE(Moogle Stiltzkin @ Nov 28 2013, 06:10 PM)
nub here, but what is prefix 64 and what is the relevance ?
*
A /64 in IPv6 is a prefix length. A single IPv6 address is 128bits in length. So /64 is half of that. Commonly end sites or host on the LAN are handed /64, and the remaining half is taken from the host MAC address. Joining them together get's you a single IPv6 address (128bits).

This is where SLAAC comes in, as it autoconfigures the host address by combining the /64 prefix length and host MAC address. No user intervention required, hence Stateless Auto Address Configuration (SLAAC).

You can also think of a /64 as a /24 class C in IPv4-land.

Hope this helps :>

This post has been edited by rogue: Nov 28 2013, 07:03 PM
asellus
post Nov 28 2013, 07:17 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


An IPv6 /64 prefix equals an IPv4 /32 in functionality, more like it.
Eoma
post Nov 28 2013, 07:44 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(asellus @ Nov 28 2013, 07:17 PM)
An IPv6 /64 prefix equals an IPv4 /32 in functionality, more like it.
*
Not quite.

A /64 prefix will yield 1 x IPv6 subnet, but it can host 18,446,744,073,709,551,616 IPv6 addresses
For the typical home scenario with one gateway/RG/AP, that one subnet and 2^64 hosts is good enough.
And since there is no concept of NAT in IPv6, all 2^64 hosts are globally routed.

/56 will give you 2^8 IPv6 subnets. For those inclined in having several subnets around the house.
IIANM, TM gives /56 for their biz packages.

This post has been edited by Eoma: Nov 28 2013, 07:57 PM
renishi
post Nov 28 2013, 07:55 PM

Enthusiast
*****
Senior Member
893 posts

Joined: Jun 2006
just a question, did mcmc just ban all the proxies?? i cant access any of them
Moogle Stiltzkin
post Nov 28 2013, 09:45 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:48 AM
rogue
post Nov 28 2013, 09:59 PM

Getting Started
**
Junior Member
75 posts

Joined: Jun 2006
QUOTE(Moogle Stiltzkin @ Nov 28 2013, 09:45 PM)
wah... so many sensei ! thx thx  thumbup.gif

so in summary you mean this ?
user posted image
so i was wondering from the question asellus posted earlier, why he thought we needed better than the current 64 ?
Or is there something i'm not seeing here  hmm.gif
what proxies ?  ohmy.gif
*
So complicated..see also pening lol...that is meant for network security ppl or ppl involve in network design software engineers..

user posted image

This 1 abit simpler rite ?


This post has been edited by rogue: Nov 28 2013, 10:01 PM
rogue
post Nov 28 2013, 10:05 PM

Getting Started
**
Junior Member
75 posts

Joined: Jun 2006
Btw, today I checked and I think my area(Subang Jaya) is covered already. Tried yesterday but nothing.

I disconnected/reconnected my connection and I can see v6 addresses.
asellus
post Nov 28 2013, 11:12 PM

#gompusas
Group Icon
Elite
4,541 posts

Joined: Jan 2003
From: BSRPPG51 Access Concentrator


QUOTE(Eoma @ Nov 28 2013, 07:44 PM)
Not quite.

A /64 prefix will yield 1 x IPv6 subnet, but it can host 18,446,744,073,709,551,616 IPv6 addresses
For the typical home scenario with one gateway/RG/AP, that one subnet and 2^64 hosts is good enough.
And since there is no concept of NAT in IPv6, all 2^64 hosts are globally routed.

/56 will give you 2^8 IPv6 subnets. For those inclined in having several subnets around the house.
IIANM, TM gives /56 for their biz packages.
*
With only a /64, you can only have one router in the network. Which is no different really than having only one dynamic publicly-routed IPv4 address. Subnetting is made harder because of this.
Eoma
post Nov 28 2013, 11:32 PM

- ,. -
Group Icon
Elite
4,603 posts

Joined: Jan 2003
From: PJ


QUOTE(asellus @ Nov 28 2013, 11:12 PM)
With only a /64, you can only have one router in the network. Which is no different really than having only one dynamic publicly-routed IPv4 address. Subnetting is made harder because of this.
*
The fine difference is one router, one subnet, but many publicly routed addresses VS one router, one subnet, one public address, and the rest behind NAT.

As i mentioned earlier, those inclined to subnet their home network further (the kitchen, room#1, room#2, room#3, wired, wireless for example) would definitely want more than a /64.

To anyone else wondering, a /64 is the smallest subnet allowable in IPv6. So a /64 will only give you one "network", whereas a /56 for example will give you 256 x /64 subnets. To which you can configure to your needs (routes/firewall rules/ACLs etc).
ihsan
post Nov 28 2013, 11:55 PM

Regular
Group Icon
Elite
1,235 posts

Joined: Jan 2003
From: kuala lipis
/64 ought to be enough for anybody. smile.gif
TSwKkaY
post Nov 29 2013, 12:49 AM

misutā supākoru
Group Icon
VIP
6,008 posts

Joined: Jan 2003
QUOTE(ihsan @ Nov 28 2013, 11:55 PM)
/64 ought to be enough for anybody. smile.gif
*
Diamlar, /32 owner tongue.gif
Moogle Stiltzkin
post Nov 29 2013, 08:54 AM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:48 AM
OKLY
post Nov 29 2013, 10:53 AM

The Penguin Vader
Group Icon
Staff
12,089 posts

Joined: Dec 2004
From: Malaysia


Have a question about QoS on our router side, it applies for IPv4 connections but does it do the same for IPv6? They are different right? hmm.gif
ihsan
post Nov 30 2013, 01:30 AM

Regular
Group Icon
Elite
1,235 posts

Joined: Jan 2003
From: kuala lipis
QUOTE(wKkaY @ Nov 29 2013, 12:49 AM)
Diamlar, /32 owner tongue.gif
*
for the record, i'm merely leasing.
prasys
post Nov 30 2013, 09:42 PM

Heros Never Die
Group Icon
VIP
12,925 posts

Joined: Mar 2005
From: Kuala Lumpur
Anyway for those who are wondering how IPV6 vs IPV4 in World of Warcraft. The difference is day and light

I am getting constant 180-190ms with IPV6 and it will be around 250-330ms with IPV4


Attached Image
rogue
post Nov 30 2013, 10:25 PM

Getting Started
**
Junior Member
75 posts

Joined: Jun 2006
QUOTE(prasys @ Nov 30 2013, 09:42 PM)
Anyway for those who are wondering how IPV6 vs IPV4 in World of Warcraft. The difference is day and light

I am getting constant 180-190ms with IPV6 and it will be around 250-330ms with IPV4
Attached Image
*
Sounda like good news for gamers..
Moogle Stiltzkin
post Nov 30 2013, 10:30 PM

Look at all my stars!!
*******
Senior Member
4,451 posts

Joined: Jan 2003
bruce.gif

This post has been edited by Moogle Stiltzkin: Jul 15 2017, 10:48 AM

3 Pages  1 2 3 >Top
 

Change to:
| Lo-Fi Version
0.3095sec    1.74    6 queries    GZIP Disabled
Time is now: 27th November 2025 - 09:10 AM