I followed the instructions for the DIR-615 router but after reboot(with a DC), it still stayed at IPv4. What gives?
Unifi TMnet Streamyx/Unifi & IPv6, Now live!
|
|
 Nov 8 2013, 09:56 PM
Return to original view | Post
#1
|
 
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe  
|
|
Quote|
|
|
|
|
Nov 10 2013, 01:47 AM
Return to original view | Post
#2
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(prasys @ Nov 9 2013, 02:42 PM) What does windows ipconfig prints out for you Here's the image. I must have missed out something. 
This post has been edited by UserU: Nov 10 2013, 01:50 AM |
|
|
Nov 10 2013, 10:15 AM
Return to original view | Post
#3
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 10 2013, 07:54 AM) The image is really empty like that? If yes, with no link-local address, your TCP/IP stack has big problems. Not empty actually, just censored out the IPs, that's all.Checked the Local Area Connection Settings, IPv6 is not connected too. This post has been edited by UserU: Nov 10 2013, 10:16 AM |
|
|
Nov 10 2013, 01:40 PM
Return to original view | Post
#4
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 10 2013, 12:45 PM) Just put the uncensored version here, nothing sensitive like MAC address is going to be shown there anyway. Here are the images. 
|
|
|
Nov 10 2013, 04:57 PM
Return to original view | Post
#5
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 10 2013, 04:11 PM) If that happens then either there are no IPv6 at all at your router, or that the router did not advertise the prefix on the network. Can you look at the webgui for the D-Link? I checked the DIR-615 dashboard, SETUP > IPv6 panel there:[√] Enable IPv6 WAN Connection My IPv6 connection is PPPoE, shared with IPv4. However, I checked the STATUS > IPv6 on the dashboard and: QUOTE IPv6 Connection Type : PPPoE Network Status : Disconnected WAN IPv6 Address : IPv6 Default Gateway : Primary IPv6 DNS Server : N/A Secondary IPv6 DNS Server : N/A This post has been edited by UserU: Nov 10 2013, 05:00 PM |
|
|
Nov 10 2013, 05:03 PM
Return to original view | Post
#6
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(JohnLai @ Nov 10 2013, 05:00 PM) Since I don't own DIR-615, I can't be sure on my advice. Can't find that setting there... Can you check if you have 'Enable RADVD' ticked? Somewhere at 'IPV6 Local Network'.  |
|
|
|
|
|
Nov 10 2013, 08:48 PM
Return to original view | Post
#7
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 10 2013, 06:22 PM) If that's the case, then the router has not retrieved any prefix from TM. Is this UNIFI? Yes, its UniFi. |
|
|
Nov 11 2013, 02:04 AM
Return to original view | Post
#8
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 10 2013, 11:44 PM) Does the router run the latest firmware version? Yep, its running on 7.17. |
|
|
Nov 11 2013, 01:40 PM
Return to original view | Post
#9
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 11 2013, 06:05 AM) If that's the case, then your exchange probably haven't enabled IPv6 yet. So it means that this is only rolled out for Streamyx, and not UniFi yet? |
|
|
Nov 11 2013, 04:37 PM
Return to original view | Post
#10
|
|
Elite
5,093 posts Joined: Mar 2009 From: Land of make believe
|
QUOTE(asellus @ Nov 11 2013, 04:10 PM) Some UNIFI users already has IPv6, maybe only at your exchange it did not happen yet. Oh well, a shame they still didn't release it in Subang yet |
| Change to: |  0.0406sec
 0.70
 7 queries
 GZIP Disabled
Time is now: 27th November 2025 - 04:48 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.