Mine is Powerline Activity is not on, power and ethernet led is on.  If I do not plug LAN cable, there is only one power led on.

I did not paired side by side. Do I need to have LAN cable connected to modem/STB for pairing? Thanks for replying

I think you may have accidentally changed the network name and they are not matched now. Try using the utility software to set both to the same network name, or just to reset both back to factory default.

Hi Guys,

i've followed the guide provided in this link

http://unifi.athena.my/index.php?option=co...id=49&Itemid=61

but still no go. my setup is like

huawei modem -> dlink DIR-615 (Bridge mode) -> Aztech Router WL830RT4 -> PC/Laptop

i follow the link above and set the same setting in Dlink DIR-615 and able to dial up from my pc, but it doesn't dial if i using the Aztech router to dial. i confirmed Aztech router settings are correct and when i checked the log from Aztech router and it keep showing message

Sending PADI...
Sending PADI...
Sending PADI...
Request timed out.

oh ya, i notice my LAN icon from taskbar showing limited connectivity if i plug the DIR-615 directly to my PC after i set the DIR-615 to bridge mode. Is this correct?

anyway, if above solution not possible..will it be possible if i upgrade to DD-WRT firmware and set as bridge mode again to use above setup? if possible how should i do it?

i found this tutorial site but i do not know which is the correct tutorial to configure bridge mode for DD-WRT firmware.

http://www.dd-wrt.com/wiki/index.php/Tutorials

any kind soul can help me out here? 

Yes you can, just pull a cat5 from the DIR-615 to the LAN port on that Planet router and make sure its DHCP server is off and its IP address does not conflict with the IP of the DIR-615.
Same answer as above, pull a LAN cable to the linksys and use it as a wifi AP. The DIR-615 has terribad wifi so I doubt it's going to be an upgrade for you.

Thanks Akerue, try it out now, I did not use the CD previously. Hopefully it works

I have had factory resetted and successfully paired them side by side with powerline activity (green light).

When I transfer them one at 1st floor; the other at ground floor, turn them on, there is no more powerline activity? Why ?

I have had factory resetted and successfully paired them side by side with powerline activity (green light).

When I transfer them one at 1st floor; the other at ground floor, turn them on, there is no more powerline activity? Why ?

---

Added on September 2, 2010, 5:43 pm

It works now, after I connect direct to wall outlet instead of power extension,

Just for a while, the pairing is unstable, I do not have a wall outlet (using power extension) on the other end

Is Caller ID really working? In my case initially was showing Private Number, after I called to activate CLIP it started showing "Out of Area". Now I am told they have a technical glitch that will only be resolved till end Setpember 10.

Maybe your power extension is old? I too use a power extension (Belkin) at one end where my BTU, DIR 615, NAS etc are located but have no problems

I have diagnosed my problem, my extension was connected from another extension, there may be lot of electronic noise affecting the pairing.  I reconfigure my extension direct from another socket outlet (due to limited socket outlet at 1st floor), it finally works. What a day !

It gets worse if you have your surge protector like those Belkin ones connected to a voltage regulator unit. These units were meant to normalize the powerline noise, hence negating the effect of home plug.

Mine also no caller id. I have called them 5 to 6 times. Yet still not there.

Hey guys... What happened to the Mikrotik Bulk Purchase ? Don't see the list no more...

Solitan SG indicated the shipment should arrive mid-Sep, but we still haven't sorted out the logistic arrangement like custom problem, payment, re-deliver to individual or self collect etc etc .... never been in this kind of group purchase before, somemore import from SG ...
Hope some member here can offer further assistance.

Btw, has anyone contacted Landasan KL? Are they bringing in?

what happen if download more than 60gb for vip5

Been using for 1 week now, online gaming, BT, internet & IPTV all so far so good, the DIR-615 working as VLAN also seem to be ok.
Except for the STB LED display which didn't display correctly, called them on Friday night and was immediately replaced with a new unit the next day morning 10am, customer care even called twice to confirm it's ok, honestly I'm quite impressed with UniFi service, hope TM continue to uphold such a rapid support 

Also been trying to replace the DIR-615 with other router, unfortunately still not working, here's my testing scenario:

Equipment: ASUS RT-N12 [Broadcom base]

Test 1 - Stock standard firmware 1.0.0.6 [come with it]
PPPoE cannot connect at all, it said something like no response.

Test 2 - download from ASUS and update firmware to 1.0.0.7 [beta]
Still the same problem, PPPoE cannot connect....

Test 3 - flashed with dd-wrt BrainSlayer R14815 16Jul10 firmware, setup as follows:
[attachmentid=1724462]
[attachmentid=1724464]
[attachmentid=1724466]
[attachmentid=1724467]
Still, PPPoE cannot connect at all ....