Hi funnyface,

May I know what is your current firmware version? The latest one is Firmware version 3.0.0.4.380.1031 dated 2015/12/11.

Try updating it to the latest and if still cannot, do a factory reset also.

http://www.asus.com/Networking/RTAC68U/HelpDesk_Download/

Thank you

This is reverse. I can't loosen the antenna anymore because the port is loose.

use small pliers that can fit the golden connector, den twist to loosen the antenna.

It doesn't solve the issue though that the golden connector is loose though as per my understanding I can claim warranty so I will do that.

Below is the log

Aug 1 08:00:11 syslogd started: BusyBox v1.17.4
Aug 1 08:00:11 kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60416
Aug 1 08:00:11 kernel: Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit earlyprintk debug
Aug 1 08:00:11 kernel: Memory: 255708k/255708k available, 6436k reserved, 0K highmem
Aug 1 08:00:11 kernel: Virtual kernel memory layout:
Aug 1 08:00:11 kernel: vector : 0xffff0000 - 0xffff1000 ( 4 kB)
Aug 1 08:00:11 kernel: fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
Aug 1 08:00:11 kernel: DMA : 0xf7e00000 - 0xffe00000 ( 128 MB)
Aug 1 08:00:11 kernel: vmalloc : 0xd0800000 - 0xf0000000 ( 504 MB)
Aug 1 08:00:11 kernel: lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
Aug 1 08:00:11 kernel: modules : 0xbf000000 - 0xc0000000 ( 16 MB)
Aug 1 08:00:11 kernel: .init : 0xc0008000 - 0xc0037000 ( 188 kB)
Aug 1 08:00:11 kernel: .text : 0xc0037000 - 0xc0390000 (3428 kB)
Aug 1 08:00:11 kernel: .data : 0xc03a8000 - 0xc03c7ec0 ( 128 kB)
Aug 1 08:00:11 kernel: External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
Aug 1 08:00:11 kernel: Mount-cache hash table entries: 512
Aug 1 08:00:11 kernel: Found a AMD NAND flash:
Aug 1 08:00:11 kernel: Total size: 128MB
Aug 1 08:00:11 kernel: Block size: 128KB
Aug 1 08:00:11 kernel: Page Size: 2048B
Aug 1 08:00:11 kernel: OOB Size: 64B
Aug 1 08:00:11 kernel: Sector size: 512B
Aug 1 08:00:11 kernel: Spare size: 16B
Aug 1 08:00:11 kernel: ECC level: 8 (8-bit)
Aug 1 08:00:11 kernel: Device ID: 0x 1 0xf1 0x 0 0x1d 0x 1 0xf1
Aug 1 08:00:11 kernel: bio: create slab <bio-0> at 0
Aug 1 08:00:11 kernel: PCI: no core
Aug 1 08:00:11 kernel: PCI: no core
Aug 1 08:00:12 kernel: PCI: Fixing up bus 0
Aug 1 08:00:12 kernel: PCI: Fixing up bus 0
Aug 1 08:00:12 kernel: PCI: Fixing up bus 1
Aug 1 08:00:12 kernel: VFS: Disk quotas dquot_6.5.2
Aug 1 08:00:12 kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Aug 1 08:00:12 kernel: pflash: found no supported devices
Aug 1 08:00:12 kernel: bcmsflash: found no supported devices
Aug 1 08:00:12 kernel: Boot partition size = 524288(0x80000)
Aug 1 08:00:12 kernel: lookup_nflash_rootfs_offset: offset = 0x200000
Aug 1 08:00:12 kernel: nflash: squash filesystem with lzma found at block 28
Aug 1 08:00:12 kernel: Creating 4 MTD partitions on "nflash":
Aug 1 08:00:12 kernel: 0x000000000000-0x000000080000 : "boot"
Aug 1 08:00:12 kernel: 0x000000080000-0x000000200000 : "nvram"
Aug 1 08:00:12 kernel: 0x000000200000-0x000004000000 : "linux"
Aug 1 08:00:12 kernel: 0x00000038d358-0x000004000000 : "rootfs"
Aug 1 08:00:12 stop_nat_rules: apply the redirect_rules!
Aug 1 08:00:12 kernel: Registering the dns_resolver key type
Aug 1 08:00:12 kernel: Spare area=64 eccbytes 56, ecc bytes located at:
Aug 1 08:00:12 kernel: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
Aug 1 08:00:12 kernel: Available 7 bytes at (off,len):
Aug 1 08:00:12 kernel: (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
Aug 1 08:00:12 kernel: Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
Aug 1 08:00:12 kernel: Creating 2 MTD partitions on "brcmnand":
Aug 1 08:00:12 kernel: 0x000004000000-0x000007ec0000 : "brcmnand"
Aug 1 08:00:12 kernel: 0x000007ec0000-0x000008000000 : "asus"
Aug 1 08:00:12 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Aug 1 08:00:12 WAN(0) Connection: Ethernet link down.
Aug 1 08:00:12 WAN(1) Connection: Ethernet link down.
Aug 1 08:00:12 kernel: ctf: module license 'Proprietary' taints kernel.
Aug 1 08:00:12 kernel: Disabling lock debugging due to kernel taint
Aug 1 08:00:12 kernel: et_module_init: passivemode set to 0x0
Aug 1 08:00:12 kernel: et_module_init: txworkq set to 0x1
Aug 1 08:00:12 kernel: et_module_init: et_txq_thresh set to 0xce4
Aug 1 08:00:12 kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.105 (r485445)
Aug 1 08:00:12 kernel: wl_module_init: passivemode set to 0x0
Aug 1 08:00:12 kernel: wl_module_init: igs set to 0x0
Aug 1 08:00:12 kernel: wl_module_init: txworkq set to 0x1
Aug 1 08:00:12 kernel: eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.105 (r485445)
Aug 1 08:00:12 kernel: jffs2_scan_inode_node(): CRC failed on node at 0x034547cc: Read 0xffffffff, calculated 0xccb2bc60
Aug 1 08:00:12 kernel: Empty flash at 0x03454c6c ends at 0x03455000
Aug 1 08:00:16 dnsmasq[384]: warning: interface ppp1* does not currently exist
Aug 1 08:00:16 RT-N18U: start httpd
Aug 1 08:00:17 miniupnpd[427]: version 1.9 started
Aug 1 08:00:17 miniupnpd[427]: HTTP listening on port 41503
Aug 1 08:00:17 miniupnpd[427]: Listening for NAT-PMP/PCP traffic on port 5351
Aug 1 08:00:17 disk monitor: be idle
Aug 1 08:00:17 syslog: Generating SSL certificate...
Aug 1 08:00:17 hour monitor: daemon is starting
Aug 1 08:00:17 hour monitor: ntp is not syn
Aug 1 08:00:17 wan: finish adding multi routes
Aug 1 08:00:17 syslog: module ledtrig-usbdev not found in modules.dep
Aug 1 08:00:17 syslog: module leds-usb not found in modules.dep
Aug 1 08:00:18 kernel: SCSI subsystem initialized
Aug 1 08:00:20 kernel: jnl: driver (lke_9.2.0, Dec 6 2015 15:53:07, LBD=ON) loaded at bf5ac000
Aug 1 08:00:21 kernel: ufsd:: trace mask set to 0000000f
Aug 1 08:00:21 kernel: ufsd: driver (lke_9.2.0 lke_9.2.0_r248656_b5, build_host("yau.chang"), acl, ioctl, bdi, sd2(0), wb, bz, tr, rsrc) loaded at bf5b9000
Aug 1 08:00:21 kernel: NTFS support included
Aug 1 08:00:21 kernel: Hfs+/HfsJ support included
Aug 1 08:00:21 kernel: optimized: speed
Aug 1 08:00:21 kernel: Build_for__ASUS_PRODUCTS_003_k2.6.36_2013-11-07_lke_9.2.0_r248656_b5
Aug 1 08:00:21 kernel: xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
Aug 1 08:00:21 kernel: xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
Aug 1 08:00:21 kernel: usb usb1: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values
Aug 1 08:00:28 rc_service: wanduck 372:notify_rc start_wan_if 0
Aug 1 08:00:36 wan: finish adding multi routes
Aug 1 08:00:42 rc_service: wanduck 372:notify_rc restart_wan_if 1
Aug 1 08:00:42 kernel: Attempt to kill tasklet from interrupt
Aug 1 08:00:44 wan: finish adding multi routes
Aug 1 08:00:46 hour monitor: daemon is starting
Aug 1 08:00:46 hour monitor: ntp is not syn
Aug 1 08:01:16 hour monitor: daemon is starting
Aug 1 08:01:16 hour monitor: ntp is not syn
Aug 1 08:01:18 rc_service: wanduck 372:notify_rc restart_wan_if 0
Aug 1 08:01:30 wan: finish adding multi routes

hi
for asus rt-n18 and rt-n56 ,which 1 is better? And my pc is installed with tp link pci adapter,can I use it to connect asus router?
thank you.

both very good router rt n18u 2.4ghz and rtn56u dual band

My unifi has spiking issues when I'm gaming, I suspect its the distance and walls in between. The unifi router is at the front part downstairs floor of my house and my desktop is in the back part upstairs.

I found from https://forum.lowyat.net/topic/3611812/all that RT-N12HP is the best for range that is not too expensive.
I will be using QoS to see if I can fix the spiking issue too. My question is, is RT-N12HP dual band? I cant find that info online even on official site.

Nope, its not..

Dual Band normally will contain "AC" word.

like Asus RT-AC55UHP.

guys budget RM200-300. which router to get ar?

the time fiber router is giving bad time on wifi, too limited range.

eyeing on asus rt n12hp for now...any other recommendation?

I just bought RT-AC55UHP router last week for my home unifi. I want wake on lan feature for my desktop Acer M3920, but no matter how i try setting just no respond. Anyone got idea how it work?

I try enable wake on lan at bios,
disable deep power off mode
enable power on by PCIE device
also enable at windows device manager network power management setting

router wake on lan that desktop just no responding, anyone??

Hi guys, im planning to upgrade my router from the stock unifi router they gave me few years back. Im comparing RT-N14UHP and RT-N18U. I stayed in a 2-stry house 22x80 my router will be placed at ground floor. Bascially all my 4pcs will be using it and 5smart phone. ermm casual gaming and also downloading from piratebay quite frequently.

n14 - 359
n18 - 479

Please advise thank you.

aususmy,

thanks for the link, i just update the firmware, working fine.

only that i notice the wifi light (2nd from left on panel) is now on all the time. it used to blink when there is wifi user and goes off when no wifi activity.

any explanation, something i may have missed?

Hi specopsmarines,

You can find the detailed information at below link.

http://www.asus.com/Networking/RTN12HP_B1/?SearchKey=rt-n12/

Thank you

Hi ASUSmy,

I have existing DSL-N12U connected to streamyx and recently I purchased RT-AC66U for extended coverage to my wireless clients. How do I set ac66u as only router and n12u as DSL modem only? I intend to disable n12u router functions (to avoid double NAT) and DHCP activated only for ac66u. Please advise.

Hi I-Kurosaki,

You can change the modem router to modem by changing by going to the WAN->WAN Connection type to Bridge.

Then connect the RT-AC66U WAN port to the DSL-N12U LAN port.

Thank you

Hi AVFAN,

It seen like the new firmware has change the LED light to solid light.

Off: No 2.4GHz signal.
On: Wireless system is ready.
Flashing: Transmitting or receiving data via wireless connection.

Thank you

ok, thanks!

is there any guide for doing QoS on RT-AC1200HP ?

intend to do it for dota 2

ASUSmy

i port forwarded some ports on N12HP, but still cannot detect that its open