haha see how the RMA goes 1st la
repost question: another question not answered, why i set in bios the cpu volt as 1.55v, but when in windows i stress using prime95, the volts shown in both HWmonitor n Everest are 1.6v?

Some boards are like that
Even my MSI overvolts in Windows, set 1.44v in BIOS, in Windows it hovers around 1.46V to 1.48V maximum

To me overvolt still better than undervolting at full loads at least in my case

UPDATE: Prime95 Blend test 17 hours and 43 minutes error free ^^

This post has been edited by shinjite: Jun 22 2010, 08:09 PM

well currently im running 300x12.5
3.75ghz at 1.55vCore HT2100 NB2100 stable prime for 8 hours already .
will stop at 24hours since im not home today, im at my rent house .
hehe

This post has been edited by monsh: Jun 22 2010, 08:29 PM

new update, prime failed after 10 hours T_T
auto restart .
dunno which part small FFT or large FFT T_T
well i guess 10 hours is considered rock solid OC compared to 1 hour stress test ^^,
passed 50 runs of IBT with fluctuate reading <-- donno y
hopefully someone can explain so i could go back and try to stabilize it back .

@xaverkiang
1: adjust HTT.. (in amd..it is HTT..in CPUZ it bus speed).. HTT x multi = core speed
2: CPU ratio is multi (Refer atas)
3: CPU NB is not the Mobo NB..its the IMC..refer CPUZ tab memory..name is NB Frequency
4: memoryZ is like to know the default timing/ speed of ur ram.. just like CPUZ SPD tab
dah..penat..can google..

@monsh
AMD = budget..
budget mobo = less durable..
less durable = less prime hour..
so if me, i prime 1hr only..sometimes 32M superpi i consider stable for normal use

haiyark like dat pulak ! i didnt even use superPI .
last time use superPI sangkut dunno y .
but 10 hours running 300 HF ref i was quite amazed with this budget proc .
hahaha
not dare to go for 4ghz cause 3.75 oso require 1.55
gila punya 45nm proc !

If auto restart means you increase voltage again...

naa auto restart more like ram not stable wan laa .
iinm, if not enough voltage on vCore always give expected less than 0.5 laa whatsoever .

normally if ram prob will get BSOD

if i were u i will listen to bro shinjite, no harm tryin addin a notch or 2 vcore. diff board diff behaviors, d only way to find out is to do trials n errors.

i wasnt at home dude, but im guessing it BSOD cause my mom said it became the normal green desktop .
most likely ram .
well im using value ram clocked at DDR3-1200 6-6-6-15 1.59V .

how far would i want add voltage to it woah .
its almost 1.6 oledi .

vCore i will add laa later .
see if it could help.

anyway, since u all so long using AMD, mind explaining the vNB and HTT volt ar ?
cause im running at 2100 means a tad bit higher than original .
do i have to crank up the voltage for like xtra 0.2 or 0.3 ?
cause my HTT voltage now is 1.35 iinm and my vNB is only 1.275 like that .

which one is affected by the HTT ref requirement ?

my vdimm is at 1.65v

normally ya proc is hardly goes dead, unless u really so LUKCY enough!!
even overheating the proc will auto turn off..

bro,did u find around garage sale?? i thk garage sale alwaz the best choice for u to find this thingy..

Guys, MA770T-UD3P is suppose to be running SB710 right? currently my mobo is unable to use AHCI suddenly and then when used cpuz to check, it says ID439D (google gave me sb750 also) does this mean my mobo has some issue? Just reformated and it's still the same. Swap sata port also and it's the same

@monsh
got HT voltage meh? i tot got HT voltage only..
i guess i was wrong all this time lah..kekeke
last time..when im using K8.. an otai ask me to increase vNB when HTT oc..
and according to bro antonio recently.. adding a lil bit (1 or 2 notches) of vNB and vHT will improve overall stability..

and vNB is not volt for CPU NB yo..

---

Added on June 22, 2010, 10:42 pmmy CPUZ also state the same (Same mobo with u).. ID439D..but currently im in native IDE (since fogot to change when formating while ago)
iinm SB710 will be written as 750 in CPUZ

This post has been edited by kuntawakaw: Jun 22 2010, 10:42 PM

Well the damn thing is i tried both (set back to native ide and ahci) and still unable to get that AHCI option back (installed windows 7 with AHCI enabled)

tried, but cant find the one like cloudwan punya

Huh?how come you cannot use AHCI?

Im using same mobo as yours..but no problems using AHCI..


You cannot get it?Some thing wrong with the mobo..
How about try updating BIOS?

This post has been edited by AMDAthlon: Jun 22 2010, 10:57 PM

well.. im not in place to tell somethings wrong..since im a noob with this
but just to share exp.. installed win with AHCI enable.but while OC....sure need to reset CMOS plenty of time.. and fogot to revert back to AHCI after reset CMOS.. after some time running in native IDE, i changed back to AHCI...and win wont boot..
happend to me few times. (2 or 3 only perhaps)... might be related or not tho

haha forgot edy how to overcome the AHCI..
since no point using it.. so not bothering anymore..
but i thought win7 no such prob..