nothing special, just wanna repair my current time



ps : all spec still the same as earlier

yeah.. i think something wrong on my HSF. How u all apply the thermal paste on the processor? maybe my method was wrong..

Yeah, that's very hot... Maybe you should try to get the temperature right first before trying to push the proc... I would use the TAT's function to load both the cores cause they produce a higher max temperature compared to running 2 Super Pi or Prime

Make sure you apply enough to cover the entire processor's heat sink, evenly spreaded out with a card, the coating should be evenly distributed with a thickness of probably 0.5-1mm. Thermal paste often require up to 1-3days to 'dry up' to reach maximum performance... BTW, also make sure that the screw of the HSF is properly locked on the back of the mobo (sometimes it doesn't go through the screw hole properly) and secured in the lock position.

This post has been edited by MaGicDust: Nov 10 2006, 10:08 PM

i am running the tat so stress both core. both shows highest 72c at default.

i think my method applying the thermal paste was wrong guah. if have a pic of how to applyin the tp would be nice

and idle at stock is about 48-50c

This post has been edited by basSist: Nov 10 2006, 10:13 PM

hot ka?? i dont thinks so. on air cooling it should be normal
same as mine here :

got 2 methods i know off:
1) AS5 official guide which I normally use AS5 application guide
2) Other method is "In the center of the cpu heatspreader, put a drop of thermal paste the size of one bb. Then just squish it down with the heatsink, lock your heatsink in"
GL
My temp. Using Ultra-120


This post has been edited by mikelanding: Nov 10 2006, 10:53 PM

i used the 2nd method. but still got high temperature

66 is normal for the stock HSF because u r running it @ full load.

my setting cant pass prime test
mayb need more vcore n looser timings

wao.. preety good temp @3.20GHz..
i am planning to get a scythe infinity or scythe mine too..
but someone told me Ultra-120 is better..
how much Ultra-120 cost?? wht was ur oc temp using stock fan??
THANKS

This post has been edited by yehlai: Nov 11 2006, 01:14 AM

Ultra-120 around Rm200+...not sure about market price. I got it from a forumer here.
I dun use the stock cooler so ddont know the temp. I actually upgrade from XP-120 to Ultra-120...I got around 10+C reduction from this upgrade.

Side Note: I couple ultra-120 with NBM 12X12X38 (sold by AllnGap) running at low speed. I tried full blast the fan, only around 2C drop. But I cant bare the noisy... . Now fan stay at low speed@1700RPM

This post has been edited by mikelanding: Nov 11 2006, 02:04 AM

I dont know... I'm using Arctic Cooling Freezer 7 Pro (Cost ~RM130 in UK)... At full blast (Without SmartFan @ 2500rpm)... I can do 57C a peak load with TAT... E6300@3.15Ghz, vCore@1.225. However, normally I'll just leave SmartFan (around 1000rpm) on cause full blast is just too loud... The temp will peak at 62C...

This post has been edited by MaGicDust: Nov 11 2006, 01:16 AM

but i am running in default clock speed and default vcore..

really? buthat i am just running at the default clock speed and vcore.. not o/c yet.

if o/c till 3.2Ghz (400x8) sure around 79-81c ||

but then u r using stock HSF ler..

i m using scythe mine now...but i think ultra 120 is better.... well i have no hardware to test out the infinity yet as my fren find its hard to remove it...so i cant borrow it from him compare ultra 120 to infinity they shd be around the same according to reviews but the size of infinity is just too big, u might have fitting problem ler.... since the performance of ultra 120 is around the same as infinity and ultra 120 is smaller in size.... it shd be better... well just my 2 cents.... wanted to get also from svc.com few days back, they put put the price wrongly .... usd 39.99 only...then the 2nd day i check again it goes back to 49.99

now i have 3 air coolers in mind.... infinity , ultra 120 or tuniq tower 120

btw my idle time for scythe mine + fm121 fan @ around 1700rpm is 42 - 45 degree without air cond and loda will be around 58 degrees or 60 ....i dunno if its good or wat...conroe is so freaking hot!!!!

This post has been edited by sup3rfly: Nov 11 2006, 04:42 AM

Aiseh...U should had act fast had grab that Ultra-120....

Yr idle temp seem to good to me. Mine idle around 45-47C.
But your delta after load is kind of bad...Maybe yr Mine cannot tame yr beasty E6700@ 3.77GHz
Why not give Tuniq Tower 120 a try since U can get it at state. We at here no chance to get it... So far I didnt see any1 in Lowyat had it. Maybe can give us a Mine vs Tuniq Tower 120 review..

fantasy_kenny and pcmoddingmy owned it b4..but its long time ago

My rig quite similar to your setup, basSist.

I'm using Mushkin 1Gb x 2 at 800Mhz 1:1 5-5-5-12 at 2.1v. Currently running at 3.2Ghz running on AlphaCool water cooling at stock voltage. CoreTemp idle at 42 degrees load at 50 degrees

i didnt expect running stock HSF at 3.2Ghz would get so high temperature

yeah similar buthen u got water cooler >.<

i got about 77-78c running at 3.2Ghz.. somemore not stable with Orthos priming. btw i am using F7 bios.

This post has been edited by basSist: Nov 11 2006, 02:19 PM

seems like V2 not so active
got a question here...anyone using hynix C4 here running ddr1000? wats the best timing and vdimm? i seems not to be able to tune it stable