Same happen to me.. my RAM prob cant take +0.3vDimm.. dont think corsair is good for OC. crap RAM
will upgrade to Mushkin or KVR soon.

Corsair VS? Care to snap a picture of the chips?

wont care if dont need to peel off the warranty sticker

yeah..i knw its air flow...but if my casing wif close panel had better air flow y the cpu temp is higher while the system temp drops? supposely is same rite? problem here is my cpu temp is higher in close panel then open panel while my system temp is higher in open panel then close panel...

dual HSF jk

try loosenin the timing lor some ram dun like high vdimm...
btw im priming orthos 12hrs ++ @ 430x7 @ 1.35vcore...vdimm +0.3v @ 4-4-4-12..vmch and vfsb +0.2v..
TAT shows load temp is 69-70ºc

corsair no good? well u cant mention ram brand lar...its the chipset more important in oc...corsair oso have high performance ram ler...u dare to say corsair h/p ram no good in oc?

i mean Corsair VS.. can c in my signature using VS

My timing already at 5-5-5-15, isn't that lose enough? That was setting for DDR2 800 btw

Value select also come with diff chip....mine using Power Chip but can run 820MHz@ 4-4-4-12 on +0.3Vdimm with ease.
Like other OCer said...is ALL LUCK...

This post has been edited by mikelanding: Oct 28 2006, 01:43 PM

mine CVS 860Mhz running 5-7-7-20...
max can take +0.2vDimm only.. no respond to +0.3vDimm.

This post has been edited by yehlai: Oct 28 2006, 01:57 PM

wow...tats oledi loose...mayb u dun hv a good chip in ur ram

yeah..nice chip

OT: dood ur vga cooler sold ka?

Just did some tweaking, still can't go pass 410FSB, the ram limiting me for sure, can't take more than 0.2vdimm, tried adding VFSB VMch all the same, can't go pass 410 while maintaining stability. 430 can boot though, but not stable enough to load window

FYI, I'm not in a air-condition room... it just that the room temp is cooled bcoz of raining this few days....room temp at night @ 25-26 ºC, morning id like 26-27 ºC. But if I OC the proc, will the TAT software compromise the performance based on it's temp reading?? coz it's a mojor 20ºC different...

not yet...want to re offer me?

Anyway, mine power chip is good till 900Mhz +- 10 Mhz (didnt really stress them). I tried change multiplier from X8 to X7 and FSB up to 450...surprisingly can boot and manage to complete super pi 1M test...but result only slightly better than DDR820.
I run the above setting after reading this thread OC Secret. Maybe U guys should give it a try...

Maybe U can change multiplier to X6 and bump up yr FSB...see how far U can push yr ram...
BTW, did u burn in yr ram? If not, try use memtest86+ and let it run overnight....might help a little bit...

This post has been edited by mikelanding: Oct 28 2006, 01:59 PM

same thing happen to me.. when try 440FSB...
U sure this is RAM prob?? my CVR can go 430FSB though.. ya with loose lanterncy la.. my only prob is cant reboot.. im quite sure this is cause by my lazy CVR

This post has been edited by yehlai: Oct 28 2006, 03:22 PM

hey guys..those ds3 user,how u measure ur vcore?take from bios or et5?which is more accurate?
and izzit ds3 got vdroop prob?i notice the volt drop when priming

I mean you don't have to peel off the seal right? You can see the marking on the chips there... Just wanted to know which chips are good and which are not

Lazy to try again, very damn sure it's ram problem, cpu can do with low voltage but ram cannot accept +0.3vdimm . Everytime i went pass 400 sure won't stay stable for more than 30mins

@bliz
mind to take a snap of ur RAM chip also??


Sure.. i'll take a snap and post it.

This post has been edited by yehlai: Oct 28 2006, 02:15 PM

btw how much vcore u feed? r u sure is ram limiting?

Same here, mine was not stable even at +0.3 vDimm and 5-5-5-15. Damn crappy CVS

perhaps lowering vdimm?

btw how need to run orthos to really show stability???
so far my 430x7 had run for 12hr++