hi guys.. im going to buy E3600 this month. I wanna know Gigabyte 945P-S3 mobo can do OC?? the result good?? this mobo is below RM 400 actually..
pls gimme some advice or recommed me good overclocker mobo please..thanks guys.

BTW do u guys know any forum tht guide newbies OC C2Duo pls..

This post has been edited by yehlai: Sep 11 2006, 08:12 PM

i need a very good mobo and ram for OC my E6300?? if Gigabyte 945 series mobo... 2x512DDR3 667 and 430W PSU. then is my spec ok to do OC??.. i will try OC soon. pls advice me.

This post has been edited by yehlai: Sep 12 2006, 08:41 PM

Im newbie in OC core2,
Just now i try OC my E63 with Easy Tune 5. I straight away push proc peformance to 120%. No doubt sure will reboot one.. but im curious, so i give it a try...
After failure and reboot twice then BIOS auto recovery... pc back to normal.

Can any C2D OC pros help me.
1) wht soft ware should i use to OC??.. (currently i have some basic tools like cpu-z-137, Prime95 ver. 24.14, Easy tune, 3Dmark03/05).
2) I only need to adjust the FSB to OC..
3) Should i modding the mobo??
4) Shall i change some BIOS setting??

thanks.

yes, i tune my grafic before.
For C2D, i only need to tune the FSB only ?? ignore other?? Really need suggestion from u guys, wht software should i use to OC.

(If only tunning FSB, then using Easy tune5 from Gigabye to tune FSB is sufficient??)

This post has been edited by yehlai: Oct 6 2006, 06:27 PM

thanks, sifu i google wht is bios F6 vers. first....

This post has been edited by yehlai: Oct 6 2006, 08:14 PM

Im newbie in OC C2D.. i tried OC my E6300 with BIOS. Push FSB to 400 and proc clock at 2.8ghz. Then i stop already. If i wanna go beyond tht wht else should i do ??
Got forumer teach me to +0.2vDimm.. is that correct??

2nd question. I use Super PI and GO-ORTHOS Beta to test stabability. But i dunno how to evaluate the score. Can some OC pros please tell me how to evaluate score please.
Thanks.

@Evogenix
can tell me which should i add volt after unstable occur please. How much the limit is.. Thanks

This post has been edited by yehlai: Oct 9 2006, 08:09 PM

wao ur E63 @3.332FGhz....
did u increase vFSB -> vMCH -> vCore ??
u increase vDimm?? how u know your RAM not stable??

So ur max voltage increase is +0.3 for vFSB, vMCH and vCore...
U know how much is your limit?? or u just watchin the temp to make decission??
Im really not dare to increase voltage like u ppl.. because i dunno how much my mobo and proc can take...

Guys,i know my quest is a bit out. But pls help me.
i was try to OC my C2D which using GA965P-S3 mobo running F2.. so i tried flash BIOS to F5.. but i dunno flash it.

This is wht im saw on screen.


FILE

Load
[Drive:\path\Filename]
___________________


Save
[Drive:\Path\Filename]
____________________

wht should i do?? Pls teach me flash my BIOS please.
Thanks

This post has been edited by yehlai: Oct 10 2006, 10:17 PM

can gimme some hint pls...

Guys my E63 only can reach 2.331Ghz (333x7).. beyond that BIOS cannot reboot. izzit bottleneck by my RAM??
Because my RAM only can go until 667Mhz.. if u adjust to 334x7, RAm is beyond 667 already. Cant reboot.

My 2.331ghz temp is 60-62C for both core. Is that too high??

This post has been edited by yehlai: Oct 11 2006, 03:36 PM

Thank you much for reminding me..
mild OC only.. not extreme...
Getting Enermax 450W soon.. but i cant wait to try OC.
i OC my grafic and E63 last nite.. run Mark03 and SP2004 no burnt.. but both core reach 61-62C.
Im using stock voltage.. i also dunno how much voltage..

This post has been edited by yehlai: Oct 11 2006, 03:56 PM

So i need to increase CPU and RAM's clock and voltage same time?? But if increasing CPU clock the RAM clock will also increase automaticlly above 667.. im using 667 RAM only wo..

but im runnig I-cute 450W also.. no OC i run 8 hours... no reboot happen..
last time i buy this PSU becasue PSU + casing only cost RM 120. i think still worth la.. because cheap casing alone also cost RM 100+. Now i plan to buy Enermax also i can still use back tht case. If really budget tihgt can consider i-cute la.

I check my CPu dan speed with Easy Tune5. My E6300 fan only run 980-1080 RPM average after i flash BIOS. izzit too low rpm?? or affcted by new BIOS???

@kcnyc.
Thank you. Ya i'll be back with new PSU. b4 Xmas i hope. Then i will come back here to learn OC from all sifu here. 10s m

This post has been edited by yehlai: Oct 13 2006, 12:41 AM

Is this PSU good enuf to OC E6300+GC??
Enermax EG365P-VE FMA 24PIN (350W)
thanks.

@kcnyc.
wao.. eys wide shut...

Hi.. wanna ask overclockers sifu here.
my E6300 stock (266x7) idle = 50-51C

but when i oc to
2.3Ghz the temp reach 58C-59C idle;
2.8Ghz reach 61-62C idle, load temp is 64-65C.

Question:
# Aft OC idle temp between 2.3GHz and 2.8GHz are almost the same.. is tht normal??
# When 2.8GHz load temp is 65C.. is tht acceptable?? (i worry when it go over 60C)
# How much vCore should i adding to go beyond 400FSB?? (normal vCore setting for my mobo is 1.32?)
# How much voltage will cause dmg to proc.??
# How to check my default vCore,vDimm and vMCH??


# I tried to oc my RAM.. i tune [FSB =266]@stock; [RAM multiplier =3] but my pc cant reboot... why this happen??
Even i tried [FSB =300]; [RAM multiplier = 2.5] still cant reboot..



*using intel stock HSF only.
*using Intel TAT to monitor temp.
*using 965P-S3 mobo

THanks

This post has been edited by yehlai: Oct 24 2006, 03:06 PM