so many error,how about if you turn off and turn on back the modem??
is still have so many error, that is tm side problem

Of course not my fault. 2 possibilities, either the area copper line old or equipment (DSLam/Exchange) problem.

can anyone tell me is this the problem cause my internet keep disconnect?
sometime connection has no problem for 1 or 2 hours, sometime just few minutes will get disconnect....then i have to turn off my router modem and on it back..

Due to low US SNR Margin. Everytime you restart/resync modem you get US SNR Margin that low?

[offtopic]
I saw TM's kancil passing by in front of my house while typing this reply. Almost wanted to shout at them
[/offtopic]

This post has been edited by Friz: Apr 16 2007, 04:47 PM

How about this? Is my line bad? Am thinking to upgrade to 1024.... not sure if I need to


Attached thumbnail(s)

i think that your line is ok..

i have my line problem also in many request time out when i ping for sample web site like 'www.google.com'.
Usually is like in 10~15min, it will have 1min request time out like that.
i possible confirm that is disconnected already. But i check my SNR margin....it is above 30 which is normal and won't get line disconnect problem~
maybe the router/modem setting will cause the disconnection happen??

I got one question ask.. Does the noise level in the copper cable affects my download speed?

your download speed??maybe not but it will effect on stability of connection,
you may have face a lot of dc if the snr margin is bad

This is mine. I was wondering about my Downstream Margin, is it normal, as I read that above 10 is better ?

DSL Status: Up
DSL Modulation Mode: GLITE
DSL Path Mode: INTERLEAVED
Downstream Rate: 3168 Kbps
Upstream Rate: 832 Kbps
Downstream Margin: 4 db (Is was 1 with splitter)
Upstream Margin: 4 db
Downstream Line Attenuation: 45
Upstream Line Attenuation: 28
Downstream Transmit Power: 0
Upstream Transmit Power: 0

Refer below, is my line very bad?
i just bought this modem, it quite good at first place but after using for few day it become sux....dissapointed...
___________

DSL Status: Connected
DSL Modulation Mode: MultiMode
DSL Path Mode: Interleaved
Downstream Rate: 1024 kbps
Upstream Rate: 512 kbps
Downstream Margin: 6 db
Upstream Margin: 18 db
Downstream Line Attenuation: 41 db
Upstream Line Attenuation: 11 db
Downstream Transmit Power: 12 db
Upstream Transmit Power: 15 db

I've got terrible connection since i use streamyx...always dc..can u guyz n gurlz analyse my detail...btw this is based on direct line(modem line direct to the phone line..no splitter etc)if use splitter more terrible

Modem Status

Connection Status Connected
Us Rate (Kbps) 512
Ds Rate (Kbps) 1536
US Margin 19
DS Margin 10
Trained Modulation GDMT
LOS Errors 0
DS Line Attenuation 56
US Line Attenuation 31
Peak Cell Rate 1207 cells per sec
CRC Rx Fast 6707
CRC Tx Fast 26
CRC Rx Interleaved 0
CRC Tx Interleaved 0
Path Mode Fast Path
DSL Statistics

Near End F4 Loop Back Count 0
Near End F5 Loop Back Count 0

This post has been edited by aliftaufiq: Apr 22 2007, 09:50 PM

Do you face a lot of disconnections? - It seems pretty bad for me with your SNR margin value..

How bout mine huh??

How do you see the margin value? Is it this?
Downstream Margin: 6 db
Upstream Margin: 18 db

And what do you think or mine?
Downstream Margin: 4 db
Upstream Margin: 4 db

Yes, and your Margin also appears to be very bad. The clear sign is you face frequent disconnection.. Correct me if I'm wrong, but that's from what I know.. - If you refer to the first page of this thread then you will be able to find out whether your line is good or bad. Refer to this link

That why I was asking around here. It seem very low but I do not face disconnection problems Surfing and Bting is fine. Can it be because of Glite?

What is Glite may I ask.


And by the way, the technician came to my house just now and fixed the micro filter or something, he then said everything is fine but he didn't fix the phone cable from the DP Box to my house.


And now I'm getting frequent DC again.


This is getting very annoying...

always remember our uncle google..don't wait for spoon feeding...

GLITE

Lol, seems pretty odd there but heck since you have such 'pro' SNR margins then why you bother to ask?

It could be the hardware fault I supposed.. Just guessing..

This post has been edited by BlueWind: Apr 25 2007, 04:37 PM