Nice... finally the Marvell88E6393X switch chip supply both 10g/2.5g/1g ports altogether... unlike 4011 that has to go through CPU...

the CPU bound also increased from 2.5+2.5 -> single 10G lane... nice upgrade!

Still waiting for wifi version..

This post has been edited by ahlong: Oct 5 2021, 06:37 PM

thats nice dude, how its perform?

So far so good, 800mbps with below 10% CPU usage.
But currently cant connect to Unifi IPv6,still try to figure out the problem...

either Unifi not giving me the IPv6 address or ROS7 is having problem, no matter what i try it does not get prefix from unifi...

Edit:
In the end,it is a mikrotik bugs on ROS7...

This post has been edited by go626201: Oct 6 2021, 11:24 AM

Hi Guys,

Just want to ask. I have RB3011UiAS but last few weeks, lightning strict and few ethernet port is out of service ( plug in but NG). It anyone here know either my router can send for repair?

Thanks

I have same problem, eth1 - 5 out of service.
now my RB3011 collecting dust~

MikroTik RB5009UG+S+IN Gigabit Router with 2.5G Ethernet and 10G SFP+ ports RouterBOARD RB

Now available at Shopee.
The block diagram disappoint me though, therefore will not plan to buy it.

I had plan to replace my recent ER12 since it has 2.5G for my home server and 10G SFP for GPON ONU SFP Stick.

What's make you disappointed with new RB5009? the 10G SFP didn't have dedicated lane?

This post has been edited by Anime4000: Oct 21 2021, 10:30 PM

If the SFP+ cage or the 2.5G Ethernet port are directly connected to the CPU (the CPU supports them), then I would have bought it.

Therefore, my plan is to just upgrade RB4011iGS to routerOS 7 when it become final.

I see,
if doing home server should be enough, since switch chip run at 10Gb and GPON ONU SFP Stick run at 1Gb.

I been trying EdgeRouter 12 and RB3011UiAS, I prefer Mikrotik way to setting networking,

also, when set PPPoE MTU to 1500 bytes, IPv6 on ER12 quite broken,

currently my ER12 1500 bytes on IPv4 & 1492 bytes on IPv6,

for Mikrotik, 1500 bytes on both IPv4 and IPv6.

what is the advantages of having the higher speed port connected to the cpu itself? I have seen the comparison in the video it says the performance is doubled compared to rb4011?

So that WAN network doesn't have to waste CPU-switch 10Gbps link capacity. With RB4011, I put WAN interface on the SFP+ cage, and all Internet traffic has its own dedicated lane to the CPU (for routing et. al), before going to the two port-multipliers through their own dedicated 2.5Gb links. For RB5009, no matter if you use 2.5Gb port or the SFP+ for WAN interface, all raw Internet traffic will go through the 10Gbps link first for routing or other things before going through the 10Gbps link again to the switches.

I think they make the cpu to utilize the container package as v7 can have containers run on it. Otherwise why would the did not put any load on the cpu?

Just bought the GPON on your link haha. Sebelum ni tak sempat beli, nanti nak follow guide flashing kat github.

Migrated from ASUS to MikroTik. This is my second time purchasing the same model, RB750Gr3. Well, since I am using 100Mbps package, I start with the cheapest gear first. Happy with my purchase.



As for the WAP, I settled down with Ubiquiti's UAP-AC-Lite, and currently waiting the unit to arrive. Both units purchased from subtlc, and the product page of both units are as follows: UAP-AC-Lite & RB750Gr3

I just bought a used gr3...
for beginners, it quite hard to do all the settings... so many functions available..

anyway... i tried to use vpn client in one of my pc... the downloading speed is horrible... is there a way to improve the performance of vpn...

I saw in the vpn connection details... it stated IKEv2 protocol...
my internet is 300mbps D/50mbps U and is getting 1-5MB download speed...

what enterprise feature for this device that is important for SME?

recheck your configuration. I have been using L2TP/IPsec over 100Mbps unifi plan so far I got full speed.

Most of it you can set VLAN, VPN server and clients, some scripting for remote or monitoring. You can do eveything in Mikrotik, even the latest beta version 7 you can run docker container.

kindly advise that to check...