RB250GS is not router, is a simple manageable Switch. I have not try using 2 same VLAN and separate into two more ports. Not sure you can do that. Hopefully can.

In Cisco, you can do private VLAN that may solve your problem.

Alternative if 250GS can't do what you need, you will have to get 2 250GS

I know. Tat's y i find it very strange. Wat looks like a 'routing table' is a port comm table. Weird.

Yes, i tot of getting 2 x rb250, for fault tolerant as well.

Hi guys,

http://www.cisco.com/en/US/products/ps10026/index.html

Currently my office has this for a foreign number. But when we connect it to the DIR615, the phone has the tone but when we try to dial out it just doesn't go through. Keeps getting constant Du Du Du Du Du sounds back.

So I was wondering is this issue due to the VLAN for UniFi?

We have no problems using this device connecting it directly to the Streamyx router nor P1. So I'm suspecting it's the VLAN issue.

well guess you solve your own problem,

when you login to the ATA adaptor, is it logged in to your voip provider ?

im guessing some network problem , open a new thread to address your problem this thread is for mikrotik only

This post has been edited by JinXXX: Feb 3 2012, 05:48 PM

Hi, RB750GL noob here. I tried the "RB750G setup file for UniFi" from KLSEET.COM available at this URL http://klseet.com/index.php?option=com_con...id=51&Itemid=49

but it's not working. The log shows that the PPPOE keeps dialing and terminating. Username and password are correct.

What's the best guide out these?

I'm trying on BIZ20 fixed IP and will try again tonight on VIP5 at home.

Any help appreciated.

can't comment about using the setup file, why dont you reset and configure it manually.. 1 by 1 following the screenshot ?

The Username is case sensitive. Make sure is same as per the Dlink router.

Was short on time at the office today so I thought I'd take the easy way out first. Will try the manual way tonight. Is the klseet.com guide a good place to start? Or is there another one?

EDIT: It's working! For some reason, possibly the KLSEET config file, the ethernet ports were reversed. Physical port 5 is Ether1 (where my vlan500 is attached). Earlier today I was connecting my BTU to physical port 1 which was actually Ether5-local-slave. I only noticed it just now in the logs (link up/link down messages) when I was plugging in the cables.

Going to do a reset and start everything from scratch. This time doing it manually.

---

Added on February 3, 2012, 11:12 pmGot it. I think I have the case correct. Will double check tonight.

btw, where in winbox do I change the IP address of the RB750GL?

---

Added on February 4, 2012, 5:18 amAll's well now. Haven't had so much fun configuring a router.

One question, for BIZ20 fixed IP, do I just use normal PPPOE as I would for VIP5 dynamic IP? Or is there a proper way to configure fixed IP (with PPPOE authentication)?

One more, can I delete the DHCP Client that's running on ether1 (the WAN port)?

This post has been edited by soonwai: Feb 4 2012, 05:18 AM

just use normal pppoe, the biz20 username is oledi linked to a fixed ip.

no matter how many times u reconnect.. it will be the same ip.

anybody using RB751U-2HnD

and have some weird problems ?

like this ?

Thanks. Next is to figure out how to utilize the 2nd static IP that I have.

You got disconnection issue?

You using build in antenna?

Wow, this thread suddenly got lots of active users.

Good to know there are many other Mikrotik users out there.

I was wondering, I have seen a few users using "RB751U-2HnD". Where do you guys buy it from?

does it happen on the 750GL?

not disconnection.. just packet drop.. just now i notice on my RB751U-2HnD

cpu hitting 100%,super slow logging to it using winbox, and im sure that is causing my earlier high tx drop rates..

fyi im using wired, got a feeling something is wrong with the firmware or the 5.12 os

nope

Can you disconnect all connection and wait few mins and see if happen?

---

Added on February 5, 2012, 8:17 amI mean wait sometime and check log if its still happen.

This post has been edited by weikee: Feb 5 2012, 08:17 AM

yeah doing that currently...

---

Added on February 5, 2012, 11:46 pmanybody know how the heck to read the supout.rif file ?

This post has been edited by JinXXX: Feb 5 2012, 11:46 PM

There's a sales thread in Garage Sales for this but I"m holding out for the RB751G-2HnD. Prefer to have GB ports.

hi all, im having problem with firewall filter setting

im planning to restriction users for access several IPs (public IP) so im implement this:



but its no effect at all, all users still can access the IP, is there any wrong in my settings?

go check the wiki regarding chain..

input (refers to router itself)
forward (pass through router)
output (well the opposite of input)