i dont know about prime, but based on my experience , linx will fail at 6.xx hours also.

Can anyone explain to me whats wrong with the gflops, how can it fly so high with HT on

because you using linx with new library, but look at your clock speed, i using 2500k at 4.5ghz can hit 124 GFlops, I think you should hit around 130GFlops,some time it gone down to 10x/11x but linx will stop at error.

nice. new linpack really improve the gflops a lot from 80 to 110ish
will try it out later

---

Added on April 5, 2011, 9:51 amUpdate: ran 5GHz @ 1.58v load with the latest linX, instant BSOD 124.

This post has been edited by owikh84: Apr 5 2011, 09:51 AM

500 times will bring up my electric bills

rather than running 500 times

try 50 with 3500mb
lol
1800mb??
eh

yeah, 3500mb.

Oh ya, did the priority made difference in LinX ?

long run no
but i normally run it above normal since real temp default is above normal also

just dont want real temp to superseed the stress test

Modded BIOS for B3 flashed to Giga B2 board:

http://www.xtremesystems.org/forums/showpo...&postcount=1672





This post has been edited by stasio: Apr 6 2011, 07:52 PM

Lol owikh ur chip need 1.58 for 5ghz? Same as my chip vcore hungry

i done it lol

for searching extremely stable setting, so far after 1 week using , still no face crash / BSOD

may i ask how to set 3500mb? only able to make it 3300, cause bro owikh claim more stress in normal mode compare to stress in diagnostics mode

---

Added on April 5, 2011, 6:38 pmalso wanna ask about the power saving feature.

when e8400 era, i oc after that i set EIST and C1E , when idle will drop multiplier and voltage.
sandy bridge i oc after that i set EIST , C1E and other power saving feature on. but only manage to drop multiplier. voltage keep constant.

is that i use offset to + my processor voltage instead of set a exact value then it will lower voltage when i idle? if not , what the use of offset?

This post has been edited by nncl: Apr 5 2011, 06:38 PM

hmm actually duno whether degraded or B3, but was lower on B2, UD7 1.52- Maximus 1.54v. those were with older linpack.
this time new linpack not sure how it will behave huhu.. will test out tonite.
will swap back to Maximus B3 once i got it within these few days. Wanna grab some new procs from shops.

For most of you, where you put the rad?
inside or outside case

i didn't say normal mode more stressful just that i play linX with background apps/services running.

---

Added on April 5, 2011, 7:04 pmif my case is able to hold 2 rads inside, it will put both internally.
easier to carry and less dust.

This post has been edited by owikh84: Apr 5 2011, 07:04 PM

oo... sry , overlooked

this is the real linpack for SB HT as it stresses CPU more than ever before.
Hit 100C within 2runs only. lol don't think I can run LinX @ 5GHz HT with the current setup+ambient temp.
Cooling limit.

This post has been edited by owikh84: Apr 5 2011, 09:08 PM

That's great It's time for us to swap CPU's so you can then try to make mine stable.

Hi there, can I know is asrock p67 extreme 4 is a good mobo for oc? I'm planning to grab i7 2600k and a good oc mobo to pair with it, tq

hi, can any1 teach me how to adjust ram or oc it? So far my i5 2500k oc to 4.5GHz stable, but my ram settings leave default.

How come ur gflop so high 120+? mine only 50+

This post has been edited by FiragaZ: Apr 6 2011, 12:06 PM