hey guys,im using e8400 EO,ep45-ud3r,crucial callistix tracer red800,i try to oc it but i get this spinning problem,i change the fsb to 420 vcore1.321 n it should go to sumtin like 3.7n then i save exit,open cpuz then,wtf it show 3.0@333.3@1333.3 just like i didnt do a thing to it,must be sumtin wrong i forgot to adjust sumtin maybe,before this 4yers ago i star to oc then i resign from it now trying to start back n forgot many things ady,can some1 explain this to me




Attached thumbnail(s)

Dual bios is in action..
re-enter the bios overclock setting page..
if the bios failed to OC the proc..the 2nd backup bios will kick in..thus u will get all default setting

can u be more spesific bro,im kinda noob here

read some here
http://www.gigabyte.com.tw/FileList/WebPag...26_dualbios.htm

which means ur OC setup is failing..instead unable to boot at all and need to reset bios..the system will boot on the 2nd bios(at failsafe setting) giving u a chance to re-enter the bios page and re-adjust ur setting

This post has been edited by serigala: Sep 25 2009, 10:47 PM

here is my setting can anybody tell me which setting should i adjust

Robust Graphics Booster ...............: [Auto
CPU Clock Ratio .......................: [ 9]
Fine CPU Clock Ratio...................: +0.0
CPU Frequency .........................: 4.05GHz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450Mhz
PCI Express Frequency (Mhz) ...........: 100

C.I.A.2 ...............................: [Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps

DRAM Performance Control
Performance Enhance....................: [STANDARD]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: Auto
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.......................: 4
tRCD ..................................: 4
tRP'...................................: 4
tRAS...................................: 12



Advanced Timing Control
tRRD...................................: 4
tWTR...................................: 6
tWR....................................: 6
tRFC...................................: 54
tRTP...................................: 4
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ......................: 900

Channel A
Static tRead Value.....................: 7
tRD Phase0 Adjustment..................: [Auto]
tRD Phase1 Adjustment..................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]

Trd2rd(Different Rank).................: [Auto]
Twr2wr(Different Rank).................: [Auto]
Twr2rd(Different Rank).................: [Auto]
Trd2wr(Same/Diff Rank).................: [Auto]

Dimm1 Clock Skew Control...............: [Auto]
Dimm2 Clock Skew Control...............: [Auto]
DDR Write Training.....................: [Auto]

Channel B
Static tRead Value.....................: 7
tRD Phase0 Adjustment..................: [Auto]
tRD Phase1 Adjustment..................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]

Trd2rd(Different Rank).................: [Auto]
Twr2wr(Different Rank).................: [Auto]
Twr2rd(Different Rank).................: [Auto]
Trd2wr(Same/Diff Rank).................: [Auto]

Dimm1 Clock Skew Control...............: [Auto]
Dimm2 Clock Skew Control...............: [Auto]
DDR Write Training.....................: [Auto]

Motherboard Voltage Control
Voltage Type...........................: [Manual]

CPU---------------------Normal-----------Current

Load Line Calibration..................: [Disabled]
CPU Vcore...............1.25000V.......: 1.38000V

CPU Termination.........1.200V.........: 1.22500V
CPU PLL.................1.500V.........: 1.5400V
CPU Reference...........0.760V.........: [Auto]

MCH/ICH
MCH Core................1.100V.........: 1.2400V
MCH Reference...........0.760V.........: [Auto]
MCH/DRAM Reference......0.900V.........: [Auto]
ICH I/O.................1.500V.........: 1.5500V
ICH Core................1.100V.........: 1.200V

DRAM
DRAM Voltage............1.800V.........: 2.000V
DRAM Termination........0.900V.........: [Auto]
Channel A Reference.....0.900V.........: [Auto]
Channel B Reference.....0.900V.........: [Auto]
__________________

some guide for u...

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.05


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 50
MCH Clock Skew (ps)...................: <<< 100-150


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [400]
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Advanced Timing Control
tRRD...........................................3-5
tWTR..........................................3-6 (May need 14 to boot first time)
tWR............................................4-6 (May need 14 to boot first time)
tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................1066-1200 (1200 may be best)

Channel A
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: << All up to your chip. If you know what voltage you need great, this board I think is about .6 or so less for actual vs what you set in the BIOS

CPU Termination…..... 1.200V*.......: <<< 1.25-1.35
CPU PLL…………………....1.500V*.......: <<< 1.5
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.3
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 2.1
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

ermmm do i really need to disable that legacy usb storage bro...........

nope..

anything that i need to change to achieve stable 4.0 ??


Robust Graphics Booster ...............: Fast
CPU Clock Ratio .......................: 8
Fine CPU Clock Ratio ..................: 0
CPU Frequency .........................: 3.76 GHz


--> Clock Chip Control <--

>>> Standard Clock Control
CPU Host Clock Control ................: [Enabled]
CPU Host Frequency (Mhz) ..............: 470
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]


>>> Advanced Clock Control
CPU Clock Drive .......................: 800
PCI Express Clock Drive ...............: 900
CPU Clock Skew (ps) ...................: 0ps
MCH Clock Skew (ps) ...................: 0ps


--> DRAM Performance Control <--

Performance Enhance ...................: [STANDARD]
(G)MCH Frequency Latch ................: [400]
System Memory Multiplier .......(SPD)..: 2.00D
Memory Frequency (Mhz) ..........800...: 940
DRAM Timing Selectable .........(SPD)..: [Manual]

>>> Standard Timing Control
CAS Latency Time .................5....: 5
tRCD .............................5....: 5
tRP ..............................5....: 5
tRAS .............................18...: 15

>>> Advanced Timing Control
tRRD .............................3....: 3
tWTR .............................3....: 3
tWR ..............................6....: 6
tRFC .............................42...: 42
tRTP .............................3....: 3
Command Rate (CMD) ...............0....: 2

--> Channel A <--

>>> Timings Settings
Static tRead Value ...............11...: 10
tRD Phase0 Adjustment ............0....: [Auto]
tRD Phase1 Adjustment ............0....: [Auto]
tRD Phase2 Adjustment ............0....: [Auto]
tRD Phase3 Adjustment ............0....: [Auto]
Trd2rd(Different Rank) ...........6....: [Auto]
Twr2wr(Different Rank) ...........6....: [Auto]
Twr2rd(Different Rank) ...........5....: [Auto]
Trd2wr(Same/Diff Rank) ...........8....: [Auto]
Dimm1 Clock Skew Control ..............: [Auto]
Dimm2 Clock Skew Control ..............: [Auto]

>>> Driving Settings
Driving Strength Profile...............: 800MHz

--> Channel B <---

>>> Timing Settings
Static tRead Value ...............11...: 10
tRD Phase0 Adjustment ............0....: [Auto]
tRD Phase1 Adjustment ............0....: [Auto]
tRD Phase2 Adjustment ............0....: [Auto]
tRD Phase3 Adjustment ............0....: [Auto]
Trd2rd(Different Rank) ...........6....: [Auto]
Twr2wr(Different Rank) ...........6....: [Auto]
Twr2rd(Different Rank) ...........5....: [Auto]
Trd2wr(Same/Diff Rank) ...........8....: [Auto]
Dimm1 Clock Skew Control ..............: [Auto]
Dimm2 Clock Skew Control ..............: [Auto]

>>> Driving Settings
Driving Strength Profile...............: 800MHz

--> Motherboard Voltage Control <--

>>> CPU
Load-Line Calibration .................: [Disabled]
CPU Vcore ...............1.27500V......: 1.31250V
CPU Termination ........ 1.200V........: 1.240V
CPU PLL .................1.500V........: 1.570V
CPU Referen .............0.760V........: [Auto]

>>> MCH/ICH
MCH Core ................1.100V........: 1.200V
MCH Reference ...........0.760V........: [Auto]
MCH/DRAM Ref ............0.900V........: [Auto]
ICH I/O .................1.500V........: 1.570V
ICH Core ................1.100V........: 1.200V

>>> DRAM
DRAM Voltage ............1.800V........: 1.800V
DRAM Termination ........0.900V........: [Auto]
Channel A Reference .....0.900V........: [Auto]
Channel B Reference .....0.900V........: [Auto]

--> Advanced Settings <--

Limit CPUID Max. to 3 .................: [Disabled]
No-Execute Memory Protect .............: [Enabled]
CPU Enhanced Halt (C1E) ...............: [Disabled]
C2/C2E State Support ..................: [Disabled]
x C4/C4E State Support ................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Enabled]
CPU EIST Function .....................: [Disabled]
Virtualization Technology .............: [Enabled]

what is mean "overclocked"

CPU : C2D E8200
CPU clockspeed : 3.2Ghz
Motherboard : GiGabyte GA-G31M-ES2L (rev. 1.x)F10 bios
RAM model : Kingston PC6400 800Mhz
RAM capacity : 2x2GB
RAM speed : 400MHz, 5-5-5-18
RAM mode : Dual channel
Cooler : DeeP Cool Killer Whale




Attached thumbnail(s)

go wikipedia ..hehe...btw u can search about this meh ...

Updated:

CPU : C2D E8200
CPU clockspeed : 3.6Ghz
Motherboard : GiGabyte GA-G31M-ES2L (rev. 1.x)F10 bios
RAM model : Kingston PC6400 800Mhz
RAM capacity : 2x2GB
RAM speed : 400MHz, 5-6-6-21
RAM mode : Dual channel
Cooler : DeeP Cool Killer Whale




Attached thumbnail(s)

Just a test using the pc of my office:

E6550@2.33Ghz (no overclocking)
2 Gig RAM
Stock heatsink..

I can see that with a stock heat sink, it can reach until 72 celcius maximum.. With no overclocking..

While my home PC, E7400, OC from 2.8 till 3.74Ghz, can reach until 72 celcius with a CM TX2 heat sink..


Attached thumbnail(s)

anyone here overclock E4500?? i checked on the first page ony e4400,i ony manage overclocked to 2995MZh which is 295x10 with 1.40vcore 2.10 ddr2 voltage & 1.35 mch voltage, more then that my pc wont stable anymore...im using a Abit ib9 mobo with 1gbx2 corsair twin xms2 with 4-5-5-15 latency & 600wat vantec psu my core temp when normal use is around 40-42c & when full load is 62c. last time i overclock to 3245 mzh which is 295x11 (my highest multiplier)stable but i need to encrease my vcore to 1.650...too much power i guess & my temp was around 75c when full load,im using a stock cooler but i use many fan & i opened my casing cover ( backside my mobo ) & blow it with my 3' table fan.....im trying to get atleast 3300mzh speed...maybe otai here can help me out...


This post has been edited by unichem: Oct 22 2009, 10:17 PM

My E2160 1.80GHZ @ 3.426
Mobo : Jetway Xblue-P45
Ram: Kingston Hyper-X 800MHZ 4-4-4-12
Cooler: Zalman 9500

OCCT Tested 10 Hours

Another Crazy Update
2160 1.8Ghz @ 3.51Ghz @ 1.70Vcore

OCCT Tested 11 Hours

This post has been edited by sky5191: Nov 7 2009, 10:50 PM


Attached thumbnail(s)

Is there anyone here who would do overclocking for a price? preferably in lyp.

PM Me and discuss your goal,i am sure we can work something out i guess

serigala,Sep 25 2009, 11:46 PM]
some guide for u...

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.05
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 50
MCH Clock Skew (ps)...................: <<< 100-150
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [400]
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Advanced Timing Control
tRRD...........................................3-5
tWTR..........................................3-6 (May need 14 to boot first time)
tWR............................................4-6 (May need 14 to boot first time)
tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................1066-1200 (1200 may be best)

Channel A
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: << All up to your chip.  If you know what voltage you need great, this board I think is about .6 or so less for actual vs what you set in the BIOS

CPU Termination…..... 1.200V*.......: <<< 1.25-1.35
CPU PLL…………………....1.500V*.......: <<< 1.5
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.3
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 2.1
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB



i have used this setting but fails...
anyone can help me oc e8400 C0 + dominator 1x2gb dominator 1066 + gay P45 UD3R?

This post has been edited by ahbun85: Oct 31 2009, 09:00 PM

This post has been edited by -tze-: Nov 17 2009, 03:54 AM