serigala,Sep 25 2009, 11:46 PM]
some guide for u...

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.05
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 50
MCH Clock Skew (ps)...................: <<< 100-150
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [400]
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Advanced Timing Control
tRRD...........................................3-5
tWTR..........................................3-6 (May need 14 to boot first time)
tWR............................................4-6 (May need 14 to boot first time)
tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................1066-1200 (1200 may be best)

Channel A
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:8-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: << All up to your chip.  If you know what voltage you need great, this board I think is about .6 or so less for actual vs what you set in the BIOS

CPU Termination…..... 1.200V*.......: <<< 1.25-1.35
CPU PLL…………………....1.500V*.......: <<< 1.5
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.3
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 2.1
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB



i have used this setting but fails...
anyone can help me oc e8400 C0 + dominator 1x2gb dominator 1066 + gay P45 UD3R?

This post has been edited by ahbun85: Oct 31 2009, 09:00 PM