as i said u nid a good ram to use lower pl value on high fsb

LOL...izit ka...i tot i wanna try 1st...ok2..

wah bro look at all ur answer & opinion u know well about oC ya...

nice2...

btw got any idea ka wut can i change without spending much money afta sell this ram..hehe...

no bro, i just started oc few month only,still new in oc. but when start to oc cannot stop already , like taking drug.
the thing i told is some review teach me too, just share with you.

btw, for 2x2gb good oc ability ram that is seen from review is Gskill super pi series, OCZ blade Low voltage series. 2 also hard to get in Malaysia

ya ka....then how lo...

waa atleast u know better & fast...

me so lembab la..hahaha....but still learning..ya like drug ma...

hahaha....hmm how eh i wanna find better ram...

if 1gbx4? any idea?

How high u wanna oc? u rly need 4gb ram?

yup run vista 64bit lo...btw i see karom got Gskill Pi series meh..

4x1GB will expensive than 2x2g, and required more voltage and more hard to oc compare to 2 stick ram.

then i better stick with this 1st....

bro, from wat i see this 2 ram quite good. 1 2

WOW OCZ...ok bro thx for da searching...

btw have to find seller here 1st...got or not lol..

bro kilowatt, before u wanna change ram, test first, or else will waste money.
usually , if ram running at same frequency , but use lower pl value will require a higher voltage to stable, u try to pump up your ram voltage and test first.

ok i'll try to push to 2.3v?...PL at 8?...

step by step pl9 try first, if stable thn pl8.

LOL...ok2...btw i look on review 1st...oredi forgot all of it...

wanna see it 1st..then try it..will update afta this..

-------------------------------

edited-

here PL-10..Timing 5-5-5-15..2.1v



and here PL-8..Timing 5-5-5-18..2.2v



nice!!

This post has been edited by kilowatt: Aug 18 2009, 01:17 AM

good start, bro killowatt. try stress it with some stability program as well,if can also try to lower the refresh cycle time as well, effect the ram performance too.

hehe...worait bro will try it later...

Hi, morning everyone..
I'm here to learn about overclock..Seems all having fun with overclock..
I'm new, so i'm afraid to do it..I need some advice from expert..
Here is the snap shot from my BIOS..Please guide me which to disable and which to change..
I'm using Intel E7400 2.8Ghz, i hope i can overclock to 3.2Ghz or 3.4Ghz..I'm using stock cooler..
And 1 thing i want to ask, why CPU sometimes will running on x6.0 multiplier and sometimes running on x10.5 multiplier? because of power saving? will it effect the speed?

[attachmentid=1150564]

This post has been edited by Lineage: Aug 21 2009, 11:58 AM

welcome to overclocking world
in this situation , u need go to bios , find cpu configuration , and disable EIST and C1E then you can run at full speed all the time.

This post has been edited by nncl: Aug 21 2009, 07:10 PM

@lineage, ur bios same with me. giga mobo?

1st, sys voltage control AUTO to detemine ur stock vcore

2nd,CPU host clock control ENABLE

3rd,sys memory multiplier 2X

4th,increase cpu Mhz little by little around 300-400 after each restart

the rest you will learn eventually

Yeah, I'm using Gigabyte G31M-ES2L rev.1.0
After i tried to overclock..my result is here..
Why my GPU's temp so high? or is it normal?
How do i know how fast my processor can go?

[attachmentid=1151706]

----------------------------------------------------------------------------------------------------------------------------------------------------------
new update :
now i overclocked to 3.2Ghz and i think i should stop..because the temp already over 50 'C and around 55-65 when normal usage..should i get a better CPU cooler? How can i know my mobo can support or not?
what cooler should i get?

[attachmentid=1151979]

This post has been edited by Lineage: Aug 22 2009, 11:25 AM