Haven't try 1.9V with it
But 800mhz 4-4-4-12 rated at 2.0v

Anyway, I've ditch it off and put back my OCZ Reapers, 1066Mhz with 2.1v no problems. Just warm to the touch

i think i was just bein lucky bro... couldn't believe i sold it for a mere RM150 only... should have kept it instead...

had a short spell w/ reaper 800 too, quite ok to my book...

http://forum.lowyat.net/index.php?act=Atta...post&id=1059693

Yeah the reapers are ok and its quite cool~~

Me running the Tracers at 2.1v 1066Mhz, around 30 minutes then Windows freezes (definitely due to the RAMs),its too hot to the touch seriously. If drop to 2.0v, it can't boot into Windows, hangs at the loading part ~_~

OCZ Reapers 24/7 also no problems at 1066Mhz 2.1v

guys, having troble here! im using windows 7 64 bit, my rig as in the siggy below, OCing my proc, this is the max i can go
http://s.lowyat.net/uploads//attach-14/pos...-1278896517.jpg
http://forum.lowyat.net/topic/1003744/+240#entry34907871
http://valid.canardpc.com/show_oc.php?id=1290656
but i still cant stabilize 4GHz of OC, tried CPU-NB voltage of 1.45v, cpu voltage at 1.52, even NB volt i pump to 1.20v, still cant get it stabilize during priming, tried every combo at a very high voltage(all combo except HT link speed n voltage and also the HTT coz im using BE proc). im using c3 revision proc, so i dun think my proc just can go an more higher, izzit because of the windows im using(64-bit) ?

btw my mobo bios setting has a very weird HT link setting, it only offer me to tweak the speed(400MHz - 2.6 GHZ), no option to tweak the 200Mhz default HT link, and also no option to increase of decrease the HT link voltage.



This post has been edited by selferino: Jul 14 2010, 08:58 AM

u forgot one thing, temperature. what's d load temp @ 4GHz? what's ya nb freq? u don't need 1.45v for < 2.6k, especially for c3 chips. bear in mind that higher imc volt will contribute to higher cpu temp. nb volt @ 1.2v is fine thou. sometimes, in order to be prime stable at certain clock, u need lower temp in order for d setup to be able to pass prime test.

correct me if i'm wrong, for ya bios, ht link @ 400MHz = ht link multi @ 2x, 600MHz @ 3x... and so on...

so ka?
when my tracer was used, it was active cooled.. so running 1066mhz all the time so never have issue of freeze because of heat. (and im pretty sure it was with 1.9v only..)
at that time.. i was noober then now..so my SS all sucks.. some SS just show CPUZ main tab only.. some memory only..so donno which one tracers SS..only have SS with 4sticks prime fail.. kekeke

---

Added on July 14, 2010, 11:09 am+ heatspreader also right?kkekekeke

This post has been edited by kuntawakaw: Jul 14 2010, 11:09 AM

With active cooling sure ler no problems~~
Mine was passive~~

The thing is it was too hot being passive~~
The reapers had no problem running 2.1v on passive, just warm to the touch

this is what i managed on a 4gb pair tracer, they weren't actively cooled but kinda warm during stress. gotten this pair for less than a week iirc so doesn't have much time to test... mileage wise reaper is definitely better...

http://forum.lowyat.net/index.php?act=Atta...=post&id=780215

This post has been edited by ah_khoo: Jul 14 2010, 01:24 PM

Tracer definitely still can go higher

yup, but voltage is a concern there bro, epsecially if they're not actively cooled.

Hmmm still not sure if the newer DDR3 tracers are also like that

The non LED ones are okay
Just the LED 1s are the 1s to look out for
Definitely need active cooling

ah_khoo, that time you run it at 2V or 2.1V?

dunno bro, but i think not as hot as newer manufacturing process will lead to less heat & volt required. u can actually direct order from d states if u have some connections there.

as per ss, 510 @ cas5 w/ 1.87v.

This post has been edited by ah_khoo: Jul 14 2010, 05:12 PM

Oh....1.9V is still okay~~

This post has been edited by shinjite: Jul 14 2010, 05:02 PM

gila u guys ram oc up to 2.1v, whats wrong with 1.65v?

what is the safe ram v for Malaysias warm temperature?

Hahahaha, they were talking about DDR2 lah bro, its different from DDR3
For DDR2 1.8~1.9v is normal.. Beside AMD chippies have no prob in high ram volt like inhell i series

so whats the max with ddr 3..... especially 1600 ?

if the ram is for intel core i3, i5, i7 series cpu, usually is 1.65v one.
for amd system, i see got 1.8v one.

This post has been edited by saturn85: Jul 15 2010, 02:31 AM

4ghz temps max load is like around 65 C, izzit not stable bcoz of the temps?

depends on chippies used on d module, d9 luvs juices while elpida/qimonda don't respond well to volts... max i reckon is ~2.0v for microns & 1.8v for d latters.

very unlikely to stabilize ya chip @ 4ghz w/ that kinda load temp, i'd say max is 55'c. d lower d better...

This post has been edited by ah_khoo: Jul 15 2010, 08:28 AM