fesick, using latest bios?
if not, try it. maybe can solve the 1:1 fsb/dram ratio problem.

oh ok..i`ll try flash new bios..

fesick, see ur ratio, 5:8 and ur mem speed show 515MHz already. Sure cannot get more than 2.6GHz lor. choose 1:1 divider.

ouhh yeah hor. didn't realize memset there states RAM speed. yeah, set to 1:1.

Hey guys,



check out more of my E2160 OC screenshots !!!

3.0Ghz

3.25Ghz

at first i manage to bump my E2160 to 3.0Ghz !!! Stable !!! but after than i tried to go 3.33Ghz (which is FSB 370 X 9)... but my RIG won't boot !!!! so i lower down to 3.25Ghz and everything works fine. i'm using Kingston value ram 667 and everything AUTO. I also never touch my Vcore... Everything AUTO !!!

Before overclock, my 3Dmark 2006 shows 6800Marks, after overclock to 3.25Ghz, over 10000Marks !!!

Lucky im not the only one with E2160 ! now im happy to have u guys here in forum to discuss with !
A few questions

1. My Vcore set to auto but it is around 1.4V when 3.25Ghz OC... is this ok ? Any danger?
2. My Stock FAN is running at 3100rpm, CPU temperature 51 degree C under LOAD, is this good?
3. Im using Kingston Value DDR2 667Mhz RAM 2 X 1GB, is it possible to run at 800Mhz ??? any problems?

have a nice day !

This post has been edited by cscheat: Sep 14 2007, 09:53 AM

Aya cakap la E2160...earlier u mentioned E2140

fesick, juz set to 1:1. 5-5-5-15. don play with memset juz yet.

guys..thanks..finally past 2.7ghz..i think i know the problem now..after i set all vcore,vdimm ++..to auto,problem solve..

mmm...auto on p35ds3 raises vcore to quite high levels leh =/

Hello, im using P5N-E SLI with E2160 here.
i tried to OC my E2160 to 3.25Ghz but now the problem is i cannot pass Super PI properly
Super PI not responding when i try to calculate !!!

im using Kingston Value Ram DDR2 667Mhz, i set my memory timing to AUTO, so is there any problem with my timings? please help !!!!!

http://img141.imageshack.us/img141/7430/325ghznm8.jpg

THANKS!

ya..so high..vcore at 1.37..but i change the vcore n now at 1.3..forgot to say that..

At that speed I think the vcore should be more than 1.4v.

the vcore already 1.4+ lo..the problem now is the ram timing..yu..ask tailo here..~i dunno oh..

The review from Tomshardware shown that 3.2GHz needs 1.5v already.

so all TAILO here, please help me !!! regarding the ram timing... im still hoping for the best

Usually for E2160 if 1:1 setting should be ok at 3.2(400x8) @ 44412/55515 (value ram). The ram also need at least 2.0vdimm.

E2160 is multiplier 8?

Haha, just want to let him lower down the multiplier. If his ram cant go further then (356x9) should be ok then.

Hey guys !!

yesterday i changed my KVR 667 to Kingston Hyper X 800Mhz Ram !!!

any recommendation for Ram timing, fsb or Ram Volts ????

Hi guys,
Just got a 2140 and a Gigabyte P35 DS3L yesterday.
Anyhow, the 2140 vcore is supposedly 1.35 volt is that correct?
But mobo show show normal vcore hovering at 1.18.....so is that normal or what (default setting)?
Do I have to manually set it to 1.35 volt?

Edit:
I'm not sure I'm doing this right, please comment on it.
1) I lowered the ram multiplier to 2, so that a 667 runs at 400 (read some guide that you need to reduce the speed, because it will be increased linearly with cpu frequency)
2) Lowered the CPU multiplier from 8 to 7 (read somewhere that it is more stable to do so)
3) Increase CPU Host frequency slowly from 200

Is it true that a higher FSB is better even though the end result is the same?
Example:
7x350 better than 8x306?

Thanks.


This post has been edited by Doggystyle: Sep 16 2007, 08:19 PM

mm..1.18? ..my mobo show normal vcore at 1.325v ..
but i dont think it will set exactly the same as what u set bios..
cuz when u get into bios try using cpu-z or any app. to read the vcore..
like mine..i set in bios to normal..but it show 1.28 using cpu-z