Any design office is in vacant right now?Mustang?Foster Wheeler?MMC?

Haha. Don't be surprised. I'm actually aiming for another Red. Not sure if it's even Red. Haha. Going to miri next Tuesday for that one. That's why I'm asking if anyone here knows any good reading material for drilling. The basic one for a newbie like me.

Wft apac early next month. U in Singapore?

This post has been edited by preakzz: Oct 24 2013, 06:14 PM

Internship placement nowadays maybe bersepah tapi kalau course geoscience macam still tak bersepah lagi..hahaha..kalau ikut our seniors kadang2 lecturer yang tolong dapatkan placement.

BTW, Baker Hughes looking for engineering-based or geosscience? Sebab selalunya O&G companies advertise vacancy for engineering je..

I have some reading materials but somehow cannot attached it here. Some of it too large.

this is some basic info,

http://www.rigzone.com/training/howitworks.asp

2014 Opportunities - Engineering Internship - Malaysia

Quote "...currently studying for a qualification in Engineering or Sciences." "For our intership opportunities we are seeking penultimate year students who: are currently enrolled in a minimum 4-year Bachelor's or Master's at the time of their intership, in a relevant technical discipline...."

more info in their website.

This post has been edited by meonkutu11: Oct 25 2013, 12:06 AM

They are starting to receive applications for Graduate Field Engineer Malaysia for 2014 also

meonkutu worked rig long time...he is master of drilling...he can set up one on one session telling from spud can to crown block

This post has been edited by orangminyak2013: Oct 25 2013, 11:31 AM

13.3/8”, K55, 68 lb/ft casing is to be landed and cemented to surface inside 17.1/2” hole.
The planned casing shoe is at 5,000 ft TVD below the cementing head.
The shoe track is 80 ft long.
On bumping the plug at the top of the shoetrack, the casing is to be pressure tested.
Take the nominal wall thickness of 68 lb/ft casing as 0.480”.
Following the test, pressure inside the casing is bled off at the cement unit.
Assuming the casing has been cemented with 16 ppg cement and displaced with 10.0 ppg mud,
What collapse pressure is applied to the casing 80 ft above the casing shoe?
Assume cementing head elevation is equal to the top of cement (TOC) in the 13.3/8” x 17.1/2” annulus. (1,535 psi)

Macam soalan exam Uni jer nie..

haha saja cut n paste sbb takda kerja

I've PM'd u if you dont mind sharing some reading materials via dropbox.

if you are still holding your OSP card then it should be fine. Client can always check the status using just that. (referring to Petronas OSP).

just go to 4shared.com and type "drilling"
anyway you need to have a specific goal what you are trying to understand
reading alone would not help
you need physically see, observe, question and make mistake to understand what you reading.
dont waste your time if you just reading aimlessly because you would not understand and would not remember after a week

This post has been edited by orangminyak2013: Oct 25 2013, 12:38 PM

Thanks!

I didn't get it pun? :-/

Alright. So no need to have my bosiet certs with me then.
Is it legal? I mean, that card is supposed to read which company i come from, right? And switching company but using same smartcard under previous company..? Or smartcard just to verify bosiet n medical status?

Alright. Already planned meeting a friend who is a drilling engineer. Thanks!

Yes I do agree that the best way to learn is to see observe and question. however thats not possible as I dont plan to jump to drilling, (but im already in the O&G sector).
however I am just reading up as additional knowledge, so if there ever was a time where I need to question things, at least I know what to question esp when it comes to planning, reading (drilling) reports, etc.
Its more like read/skim through to get a general idea.


I dont have. I'm requesting from meonkutu11 if he could share via dropbox


Shouldnt be a problem. I mobilize hundreds of workers and although I'm not in the manpower department I believe PCSB just has to check their system on the validity of the OSP (that it is not a fake and certs are still valid). After all, we do handle alot of freelance or temporary contract workers who have been working for different companies.

This post has been edited by echobrainproject: Oct 25 2013, 06:55 PM

Sure but mainly in Support Management role.

I'm myself from IT but ended up doing HR job for O & G.

they still don't have a strong engineering arm. they always form a JV with AKER for engineering. Technip is already tied up with MMHE.

This post has been edited by Stamp: Oct 25 2013, 07:36 PM

i suggest you put a source instead of....
Drilling Ahead

Basic Design:
For API Casing Design, Collapse Pressure is using design factor 1.125.

Pc= 0.052 x mud weight x depth x design factor.

This post has been edited by ch_teo: Oct 25 2013, 10:51 PM

Not really boss...I'm just a roughneck..

Future director of drilling.

Boss,
want to ask whether you have used electrically driven drilling?