what is the best ram for intel range below rm500 for 8gb kit?? can any shifu help me

MAXIMUS-V-GENE-ASUS-0086

http://www.datafilehost.com/download-d9563a08.html

Added SPI Booster option, enable to see if can boost superpi times slightly

This post has been edited by stasio: May 30 2012, 09:10 PM

im testing the cpu from a few to run the benchmark..

i'm not sure what you mean power sucker for a 22nm cpu, partly it is due to the thermal interface and not a power sucker compared to AMD FX and LGA2011..

daily use 4.5g is enough for me within the temperature range in full loading..

running benchmark =/ daily use.. it is just for hobby

i am currently using corsair vengence 2x4gb 1600mhz
i just received g skill ripjawsx 2x4gb 1600.

which would be the better ram to use?

oh.. i means ivy need lot vcore to get higher ghz. if compare to sandy la.

4.5ghz is really enug for daily use .

Ivy Bridge goes over 7GHz mark

ASUS ROG CPU-Z 1.60.1

ftp://ftp.asus.com.tw/pub/ASUS/misc/utils...1601_XPWin7.zip

ASUS MemTweakIt_V1.0.1.7

ftp://ftp.asus.com.tw/pub/ASUS/misc/utils...1017_XPWin7.zip

I'm on subzero for the first time.

Quad TEC + 2x RX360 + 12x GT + EK X2 250 Adv + EK FC7970 + D5 + EK top + XSPC white tubing


Quad TEC + Dual controller:


3770K @ stock


idle:


load:


This post has been edited by owikh84: Jun 9 2012, 10:22 PM

Not worried on condensation?

No worries on condensation as both the mobo + TEC block are insulated properly with Kneaded Art Eraser.

Itching to buy this quad TEc
I think you need 2 psu when running trifire 7970'and i7?

the mobo heatsink is freezing?

This Quad TEC is works insanely great as per descriptions in the original OCN thread.
I still got an extra TEC, the single TEC but haven't tested the replacement top which was cracked previously.

My SB-E rig doesn't really need more than an AX1200 for stock trifire 7970 + OCed 3930K.
AX1200 can pull more than 1200w out of specs.
Quad CF needs 2 of these PSUs.

Want to sell the single TEc?
What if I don't feed power to TEc and just let it run passive. How much worst does the heat dissipation get for the block.

CPU socket + backplate + TEC block are the ones tend to condense when going extreme cooling like this.
Not the mosfet VRM part when it comes to CPU-only cooling.

---

Added on June 9, 2012, 10:51 pmI will sell the single TEC after testing ok. But you need a low room humidity to make it worked = airconded.
The TEC block without controller power performs badly for sure.



This post has been edited by owikh84: Jun 9 2012, 10:51 PM

My humidity is around 30 to 35 percent
You dont have the controller for this?

Good for you. yes i have the single controller in the first page of this thread.
I need to do a leak test first before putting this up for sale though & it won't be cheap.

Great. Drop me a mail when you do
TEc sounds really interesting

owikh84:- sweet!!! can i have a quote for the item price??

I've put it on sale in our GS pls check it out.

Update: there's a false reading on the RealTemp as posted above the lowest core temp should be 0C minimum because by default Realtemp reported 91C as TJmax as opposed to original spec which is 105C.