hehe...nice setup bro!!!
what brand of tubing u use??feser??looks like the tube is kink...
try change the orientation of the tube from mosfet to cpu wb to other side...just change the orientation with the tube from rad...
last time i use promoflex...less kink IMO ...

This post has been edited by selfdz87: Jun 15 2011, 02:22 PM

Oh man...you guys setup is beautiful!

ya bro.. got kink there u gonna have to use adapter or change the routing

jack, if the mobo block and the CPU block are on the same height, then can simply use the 90degree barbs, like the one in black color that's already on your mobo. Looks good too with a pair of parallel 45degree orientation tube.

maybe u should turn the pump around... so that the oulet face toward the mobo block... will be less kink and use less tube...

i notice 1 missing fan there .
that casing aint really for WC setup man .
really a pain in d arse .

dang my EK-D5 top just fail on me today...it leaked...i noticed it when the pump start making a buzzing noise and there's water all over the floor...lucky me no hardware failure...switch off my PC just in time....fuhhhh....

fuh lucky u bro... what went wrong..? is it the o ring..? or u didnt tighten it enough

its not the o ring...but its mybe bcoz i tighten the comp fitting to hard until it loose(the outlet hole)...
one of outlet(middle) cannot be use anymore...thats the end of it i think...if ill try to use another outlet...the other one will leak again IMO...

Water cooling can be quite a disastrous if not done properly and carefully. I once had a tubes disconnected from the barb when I was tilting the PC to bleed out the air, and the water sprayed all over on the mobo...and the worst, I forgot to unplug the 4-pin molex on the mobo...it was a stupid careless mistakes I made. The PC won't power up after everything was done, got pissed off, I went out yam cha with friends. Luckily when I came home after few hours, the PC started up without any issues. Lucky...

i think i read it somewhere u cannot over tighten it coz it will make the o ring thin and causing leakage

ya,i know,but dont know wat to do bro.

dont worry bro.. just get a pair of 45 or 90 degree adapter.. problem settled

owh,ic..

so i should buy 90dgree barb,and glass tube for connect the barb?

i also got leaking between tube and barb.so,ur suggestion?

wta,fitting is for what?

---

Added on June 16, 2011, 1:38 amcan u give me the picture?

---

Added on June 16, 2011, 1:43 amyup,the tube is kink.

i guess,i should buy 45/90 dgree adapter or change the tube.

This post has been edited by jack_ass69: Jun 16 2011, 01:43 AM

u already have barb. just buy adapter. what barb u using.? bitspower..? i believe the leakage is caused by the kink

jack, these are the examples:



By the way, that kink looks real bad. With the pump pushing the water, that kink is a big restriction for the flow. Pressure will build up, and leak will occur at weak connection point. At worst situation, it's possible that the tube will disconnect from the barb fitting and spraying water all over the place...

This post has been edited by hian: Jun 16 2011, 02:02 AM

leak often occur at rotation point of rotary connector .

quite impossible to occur at connection between barb + tube .
the kink doesnt look like its going to kill d system .

dun get rotary barb unless u have to .
just use normal one and reposition ur items .
better option .
i oso not using much rotary cause tendency for leakage quite big .

owh,ok bro.
thnks bro,i guess i hv to buy this item.

dont have to buy the ones with comp fittings. just get the adapter is enough. btw what barb u using..? is it bitspower..?

best to use maximum 2 90 degree... too much will be flow killer and a burden for ur pump... as in ur pic, already have 2 90...