HTT yes..sure u have to tweak it to find the sweet spot..
HT link..u can leave at 2ghz +- abit.. will not increase performance.. it might increase if use IGP..
the volt.. sometimes when i OC..i give some extra volt to HT and NB..legend said that it will increase the stability..kekeke
after finalize, then will reduce back if stable.kekeke

HTT link speed n HTT is the same thing ryte? n i shud juz leave it at default 800MHz value eh? btw since im not touching or OCing the ram at all( BE proc ma), i dun have to blend in prime95, juz the normal in-place large fft onli ryte?

---

Added on June 20, 2010, 12:22 amor ur HTT u mean the FSB?

This post has been edited by selferino: Jun 20 2010, 12:22 AM

HTT and HT different thing bro
As shown in cpu-z
HTT = bus speed
HT = HT link

HT default should be 2000mhz

wait.. HTT (BUS SPEED) is the one that stock at 200mhz..HTT x multi = CPU freq
another 1 is HT link..both is different thing..
HTT x HT multi = HT link speed..

i wonder what board u use eh? y stock at 800mhz?
since both u and i donno what FFT used to stress the IMC alone, i suggest to blend.. so it will stress both CPU + IMC inside ( and ofkos ram included)
or wait tomorrow for sifu to come out ( i doubt they will..since most of them esp Ah_khoo and cloudwan only spam here during office hour )

check my siggy for wut mobo im using msi 770-c45

---

Added on June 20, 2010, 12:35 amowh yeah not 800Mhz, its 2000Mhz, same like cpu-nb freq, at 200MHz*10

This post has been edited by selferino: Jun 20 2010, 12:36 AM

perhaps some screenshot of cpuz will help clarify some things

owh typo up above, did not mean HTT link, but HT link multiplier and volt

---

Added on June 20, 2010, 12:38 amso repost question with correction, do i need to play around wif the HTT link speed and voltage? coz never saw anytin bout tat in the phenom II guides..(not talking bout HTT or cpu-nb)

This post has been edited by selferino: Jun 20 2010, 12:38 AM

kekeke..so the 800mhz is the idle C&Q state for ur CPU right?
newer mobo where got stock at 800mhz.. if my mobo ye la...stock at 1000mhz..kekeke
i usually alter the width only..16.i donno the benefit..but like the number instead of auto.. others seldom touch.. only sometimes the volt..
if u want to OC the HT link..go ahead..but just dont make it more than ur NB freq..if more, then u have to korek2 ur CMOS jumper lah..kekeke

edit:repost answered question

HT link..u can leave at 2ghz +- abit.. will not increase performance.. it might increase if use IGP..
the volt.. sometimes when i OC..i give some extra volt to HT and NB..legend said that it will increase the stability..kekeke
after finalize, then will reduce back if stable.kekeke

This post has been edited by kuntawakaw: Jun 20 2010, 12:42 AM

juz rebooted( now tryin to stable my 3.9Mhz on win7 64 bit), i rebooted coz my HT link on cpu-z was 800Mhz, so went tobios n see the multiplier was auto, so i change to x10 to 2000MHz, wish me luck, do giv me tips if any tq

---

Added on June 20, 2010, 12:47 amweird disable CnQ oso the HT link is drooping to 800Mhz, wat la u mobo MSI!

This post has been edited by selferino: Jun 20 2010, 12:47 AM

tips? mix HTT oc and multi even if u get BE chip..sometimes it will yield better result..
and also..the vcore? ganas betul pkai budget mobo for this task..kekekekek
cool ur mosfets bro.. or else ull be PCless..

takpe bkn nk OC 24/7, so far pakai 1.45 cpu volt max jer, skunk 3.8 dh boleh, 3.9 jer blue screen nie, tweaking2...

---

Added on June 20, 2010, 1:08 ambtw wuts the difference between CPU-NB VDD Voltage and CPU-NB Voltage?

This post has been edited by selferino: Jun 20 2010, 01:08 AM

VDD is default voltage.. normally leave it auto..
CPU also have one.. not only CPU-NB..

we normally play with CPU-NB Voltage which is an offset of CPU-NB VDD Voltage

for example.. 1.35v + 0.025v

because not all cpu are equal..
maybe 1.4v + 0.025v etc

or maybe we can underclock the cpu by using it..

kene kutuk pulak , i confess i'm a spammer thou...

small ff = cpu only, blend = cpu (8-512k) + imc & ram (>512k) from what i know, but i'm not sure coz i'm a lazy ass when it comes to researchin...

brisby g1 sure a tough nut to crack, could be user problem thou... age is catchin up...



This post has been edited by ah_khoo: Jun 20 2010, 11:02 AM

If Im lazy to change my mobo 770 c45 to crosshair 4 and change to 1090T.
Any issue I will faced with that pairing? Buying new phone, so now money now.

maybe need to update bios..

Yup maybe just need 2 update bios and ur set.. Tho are u going to oc kaw kaw later on?
If yes then i'm kinda worried with the 770-C45 pwm's longevity

for benchin still can take i think, but for primin (even short hour) it's too much to handle i reckon. 1090 on 770? i wanna see fried mosfets...

This post has been edited by ah_khoo: Jun 20 2010, 05:43 PM

Wahhh unker, im oso using ta690G + windsy 5600+ on second rig~

low clock speed and high at ram speed~

wow... windsy... nice chip w/ 2MB L2 cache there sis...

this is almost d max i can afford w/ my limited skill, d ram could go further under d hands of sis xixo...


very late submission for brisby g1, ts dun get angry yerr...



AMD Athlon X2 4400+ G1 | 2800MHz | ah_khoo | TA690G | OEM Crucial Value DDR2 667 | 933MHz | 4-4-4-12-16 | AMD stock cooler (w/ heatpipies)

This post has been edited by ah_khoo: Jun 20 2010, 04:54 PM

yes, succesfully burn my mobo(i think coz suddenly shut down during priming), haih tangan gatal sgt nk stablekn 4Ghz on my proc till kt bios Vcore set 1.55v ( thou everest n Hwmonitor shows 1.6v), tested my ram, gc at my fren comp still working, tried his psu at my comp, same case not booting( yes already did clear CMOS), now not sure yet whether my proc, my mobo, and my psu is still ok. Mobo confirm dh out dh, tp proc ngan psu xtau lagi, xde tempat nk test, haih....dh stable 3.9Ghz gatal nk kejar 4Ghz, haih....::