I just ask foreman to check my car. He cleaned the fuel injection head. And he said that fuel filter below the seat is old and kind of stuck. So that cause the car to shake when I am trying to push him to higher rev. Anyway, the early start of the car that the car will rev high then drop to 0 still exist. The foreman said after the head cleaned, it should be no problem. But this morning this problem occur again...Argggggghhhh... What to do? Any suggestion? Tuning??

fuel pump?

hi all, just find a place for my waja after 6 mth. please add me. 2004(2nd) waja 1.6 4g18 Thank you

Just sold my Waja today.
'Twas a good 4 yrs + that it had serve me

start from the source " the Battery" (+).

---

Added on January 18, 2009, 10:56 amcongratulation.


This post has been edited by zenwarlord: Jan 18 2009, 10:56 AM

Have u done MUT check??Any error detected??


Haha..Now using what car??
Ur K&N filter does serve me well..
But i miss my HKS slurping sound

This post has been edited by aliftaufiq: Jan 18 2009, 11:13 AM

the weird thing is that the alarm + central locking works fine. in fact, anything that uses the battery, but w/o the ignition key turned on, works

the batt was replaced less than a year ago.

the 100Amp fuse on the batt + lead is fine. so is the 80A batt fuse in the fuse compartment. all fuses are ok, except for the 30A fuse marked with "key and switch" logo. it keeps burning out even if replaced with a new fuse

anyone got the electrical wiring / circuit diagram for waja? mebbe need to trace and check the key ignition switch line

Glad that you like that K&N filter..hehe!
Bought the new Honda City.. waiting for it to be delivered. Hopefully they can get it to me before CNY.

That new city looks elegance
Spotted 1 nearby Restoran Hakim Seksyen 7 Shah Alam n the owner ask me where did i paint my car..Baru use 1 week thinking to repaint to crystal white

Oh, I haven't spotted any on the road yet (except those test drive units).
What color was that guy's City? The problem is Honda Malaysia didn't launch the Taffeta White color in Malaysia or else I would have taken that color too. It's sweet!

Guys , when i arm my alarm... sometimes the alarm will went off and sometimes not. i suspect is the boot or the door doesnt closed tight enough... but i test it by shutting the door tight and try to pull a bit when the alarm is armed... the alarm doesnt went off...

asked my fren , he said maybe is the battery low... but i checked, the battery water enough...

i wanna confirm from u guys , is the alarm try to tell me something wrong with the car or the alarm reached the time to change?

the alarm went off immediately or after few hours? some waja got this problem where the cold temp at night warp the metal and the alarm go off. when is the last time you change ur battery?

Battery water level does not indicate battery power level. I also think the battery level is low.

cant say when it will went off...sometimes immediately, sometimes few minutes, sometimes hours...

not only at night it will went off but also morning times and afternoon times ...

i remember i just change the battery half year ago...


hmm... is there a way to check the battery level?


anyway thanxxx guys for replying...

Ok guys! i will update you on my latest DIY project.

Lately i noticed considerable road noise. I checked under the rear wheel wells and found that the black stuff have stripped away leaving the metal exposed.

Went to ACE hardware (again) and bought myself 2 cans of Mar Hyde (you can use other brands too) RUBBERIZED UNDERCOATING.

i used newspaper and masking tape to cover the area surrounding the wheel wheel and wrapped up the suspension with newspaper.The tires need to be wrapped too.

i jacked up my car, wrapped a cloth over my nose and mouth, and sprayed the whole wheel well. 1/2 can per wheel well. I did it yesterday morning and it took 24 hours to dry.

Today i checked but still not satisfied with the thickness so i decided to spray 1 more layer. Should dry just in time for me to get to work. i will do the front wells next week because its tiring and the stuff takes forever to dry.

Will update you guys on the results tomorrow!

Tips: That undercoating stuff is nasty. Don't breathe it in. Even with the face mask i felt dizzy and had to stop after doing 1 wheel well. Also, don't be a hero and empty the entire can on 1 wheel well because it will take 4 to 5 days just to dry if you do that. even a 1/2 can coating took 24 hours to dry lol.

Also, use another jack to support your car as backup or use a car stand. Sometimes car jacks can fail. Safety first.

"key and switch" fuse burn bcos that is the very 1st on/off circuit, if that fuse don't burn then it will damage ither device even ur ECU. Did you install anything lately? Worst to the worst u need to remove all the deivce such as HU, Aircon panel, meter, hazard module, heater, wiper, power window and see whether the fuse still burn.

---

Added on January 18, 2009, 2:46 pmdouble confirm your front bonnet and rear boot switch.

---

Added on January 18, 2009, 2:47 pmuse multimeter.

---

Added on January 18, 2009, 2:52 pmany photo to share?


This post has been edited by zenwarlord: Jan 18 2009, 02:52 PM

zenwarlord , please enlighten me wheres the switch by showing me pictures... thanxxx

I don't have pic for the rear boot, u need to open up the boot and look around the latch area.

this is very true. most waja have this problem. the solution? adjust the plastic bracket higher that is marked in the circle

my waja oso got this problem for the 1st few months after buying. adjust itu balang problem ilang

Installed my Eclipse CD1000 HU at howie's place today. Sadly his boschman component set all sold out, any recommendation for component set and woofer?