This is one of my clients PC I've build... Short run overclocked to 3.6GHz stable could have gone further but not enough time to test everything out... Using Hyper TX2 cooler for testing..

SuperPi....


Orthos for over an hour...


EIST is active...


For some reason, both System Properties, EasyTune and others reports 3.75GHz instead... Running on GMA IGP which doesn't like anything above 280MHz system bus.

This post has been edited by lex: Jan 23 2009, 06:25 PM

count me in...

i'm using this proc oso...

OC it to 3.15 onli with stock cooler, hehe...

252 x 12.5 @ 1.200v mem divider 3.33 @ 840mhz @ 4-4-4-12

Idle temp about 40c & load nearly 60c

but i noticed that core 1 & core 2 temp isn't the same?

Normal meh?

I can get up to 3.2GHz on the stock HSF... Anyway, its was fully stable up to 3.75GHz (only the IGP held it back, a discrete GPU required) and I did managed to touch almost 4GHz unfortunately the DDR2-800 value RAM held me back from reaching that goal.... Going to send this PC to client soon...

i just bought the same mobo too coz my pc suddenly no post eventhough there's power running through..so i tried to pair my e5200 wit the giga g31 rev 1.1 but same prob occur tried wit one stick ram oso still the same..tried other gc oso same issue occur...the only things left are psu and proc...is there any possibility that my proc dead?

Ya, i managed to reach that level too, but sumting weirdo will happen if i set above 3.15Ghz

My P35 DS3 rev1.0 would power on for a 1-2sec than immediately self power off, than back on after 1-2sec later
with all overclock setting remain & happily continue loading as normal

It happen every time during cold boot...

I tried tweakin it to many different settings but it still happen

What's wrong eh? Anyone facing this issue b4?

I'm on 3.3ghz on Stock Cooler. Temp is okay but you need to play with vcore slowly. If increase too much, its won't pass 3dmark06...just "sedang-sedang"....

Have you tried resetting or clearing the CMOS settings?

Anyway, the PC already sent to client.. Here are some pictures with my cooler, was replaced with the original cooler before send off..


Overclocked at 3.75GHz stable with reduced voltage testing, passed Memtest easily..


This post has been edited by lex: Jan 25 2009, 08:32 AM

Now doing this settings...

CPU---> 3.3Ghz @ 264 x 12.5 @ 1.225v
MEM---> 880Mhz @ 264 x 3.33 @ 5-5-5-15 @ 1.9v
TEMP--> 42c Idle & 62 Load w Stock Cooled

Hehe, not bad eh for a newbie like me

Gonna push this baby summore & see how far it can go

TORTURING TIME!

p/s - any sifus pls enlightened me wif ur OC skills, make me ur padawan...

E5200 user reporting in


I managed to clock @ 3.9GHz on 1.65V, vdroop 1.55V

E5200 (312x12.5)
Asus P5B-E Plus
XMS2 2x1GB 800MHz @ 936MHz

Fail orthos on 34mins 7 secs. Will try higher vcore later

higher vcore?

Haha.. Wanna try what voltage enough to stable it.

Btw, safe vcore is? I no idea about this.

This post has been edited by Liuteva: Feb 2 2009, 10:53 PM

Wah! 1.6v! & u still wanna push higher?

I bet u use a decent cooler which made u dare to do that eh? Watercooled maybe?

Me no chance ler to do near 4Ghz with stock cooler

this baby really need quite a voltage bump in order to bump

For now, i guess i shud stick wif 3.3GHz until i get a decent cooler...

Was using Deepcool KillerWHALE

E5200 @ 3.6GHz (288x12.5)

vcore 1.45v, vdroop 1.384v

Mobo: P5B-E Plus
RAM: XMS2 2x1GB 800Mhz @ 960MHz (5-5-5-15) 2.25v

idle: 37c, load 67c



WTH, my mobo vdroop so high

Oh, no wonder la, kudos for that great cooler...

I was planning to buy it as well but unable to make decision coz
stuck in between Deepcool or Thermalright or Not-Yet-Released cooler from other brand
that can support socket 1366...

Want it to be future proof maa coz planning to upgrade to Core i7 in near future

Haha i see, now grab and enjoy first ma, future buy again

This post has been edited by Liuteva: Feb 5 2009, 02:42 PM

I also have the same Vdroop (down to 1.36V to 1.38V).. However I didn't need to pump that high Vcore to reach 3.6GHz full stability. Even with a crappy Hyper TX2 cooler the idle temperatures were below 30c and on load (using Prime) never even touched 60c.

Nice temp you got. Using what thermal grease?

I using the whale stock thermal grease, the performance didnt do well

Idle 34-35c, Load 67c

anyone using this proc with asus p5kpl-am ? wonder how far can it go gonna make a setup with this mobo soon

Just got this processor yesterday.

Pairing it with ASUS P5QL PRO.

Anyone else has tried pairing it with P5QL PRO ?

Ahha! Oledi got myself a 2nd hand TRUE cooler from a fellow forumer

This time gonna torture my E5200 kaw kaw...

& let the FUN begins!

---

Added on February 10, 2009, 10:49 amAiyaa...

Even with TRUE cooler my idle temp is quite high at 44c, about the same wif my stock cooler...
I was expecting it to be around 35~40c onli

Load temp imho is low however around 56c

My settings > 3.3GHz @ 264x12.5 @ 1.200v onli...

Reseated it thrice already & the third time with EXTRA careful using
AS5 thermal paste...

WHY? WHY? WHYYYY!!!! HELPPPP!!!



This post has been edited by vamfire: Feb 10 2009, 10:49 AM