Does the Smart Map feature work with Malaysia region? Already ran the full cleanup a few times but still not seeing any map under Map Management.

no lldar on 1c i believe so no mapping feature available

Work for me

mine after update firmware, dun look good,
jerking, spin wheel pushing wall, can't find home ...


already try reset map .. and already try factory reset ..
no luck, now cannot create map, due to cannot home and map not can't save.

regret habis .

Basically around 3 times of full run. It will store the map and split by zone. From that time onwards, I'll pick whichever the zone that I want to clean. Can select multi zone to clean up. Make sure updates your firmware to latest version..

Second screenshot show it clean 3 zone those I've selected.. cause some time you might close certain door and if you just run full cleanup, and bot can't access to that zone and it will trigger you that particular zone route get blocked based on last clean. So I'll prefer to get bot clean by zone

This post has been edited by ChuanHong: Mar 8 2021, 01:55 AM


Attached thumbnail(s)

My robot does not dispense water anymore.. Haihzz.. Few days of mopping, water level is the same

Anyone got solution for this?

Air inlet blocked by water probably, tiny hole located at the rubber cap

I tried to use something to poke it.. but still the same
The cloth only have 3 water spot, at the water outlet hole.. and it's not wet at all..

Don't need to poke it, just make sure no water inside the hole, use cloth or tissue. Don't care about water outlet hole, wet the mop cloth before install. If can't fix maybe have to ask your supplier for support.

i also just got it... i dont know how to use.. does it scan when 1st clean or scan first then clean?? its seems confusing...

Bro,

how to draw virtual wall? i scare to put the robot upstairs scare it sweep the hall then come to stairs fall down tai wok liao...

hi all, anyone can help? this is my 1st time using the robot... i have questions to ask...
1. when i share the app with family member, how come they can't add the room for scanning?

Don't worry it's smart enuff not to fall off stairs

it will clean & mop while scanning for first few times.. no confusion here..

after 2~3 times, the map will shown accordingly.. refer few posts above and you could see my screenshot..

To be safe if you put upstairs

1. Buy Xiaomi robot magnetic wall barrier (A brown magnetic tape)
2. use the app go to the 3 dot upper right -> Turn on "Experimental feature" (Map saving mode)
3. Let the robot MOP upstairs with your supervision and with Temporary barrier
4. The robot will start building the map, will take 2-3 runs before MAP is build
5. once MAP is ready under "MAP MANAGEMENT"
6. Start adding software virtual wall

For up stairs where the chance of suicide is there I will put virtual and magnetic virtual wall to be safe... dont want the robot start suiciding

although xiaomi robot has build in drop sensors and stuff sometime I notice it will overshot the ledge

This post has been edited by calvin_ng: Apr 22 2021, 11:00 AM

I have build the map for my living hall downstairs... then for upstairs do i need to press the + button and scan the device again????

Hahaha.. Bro, are u sure?
I don't dare to use upstairs.. cause it drop into my kitchen area.. my kitchen is 3 inch lower than my living room...

Ahh? I thought need to poke it. LOL.. i try to dry the hole, and see again if it works..
It's been 1 week i never topup water into the tank

Yup been letting it run freely for 1yr upstairs, never falls off,since it has drop off sensors

This post has been edited by DM3: Apr 23 2021, 06:07 PM

idk why people need lidar maybe for complex home

but for normal simple condo/apartment, my xiaomi works fine, many dust collected and hairs. run 3x per week. it practically outperforms me. only qualms are i have to mop the corners

not bad paid rm700 during shopee sale cw a electronically controlled water tank, 1 sweep type