threads merged. seems logical it belongs here

@zeustronic
nice ram u have there
oledi switch frm 478 to C2D?

I up before 1090Mhz but not stable.... u can try A-Data DDR2 800Mhz...COOOLL

alo bung, bila lagi mau kasi show-off itu tuniq?

wanna c the performance is killing or not

u directly b0ot from bios or u overclock in windows environment using uguru?

finally i can run my pc on e6600 @ 3.6Ghz (400fsb) but at 1.6875vcpu!!! it passed SuperPI n orthos (less than 1 hour n lazy wanna wait) with stock HSF but open side panel n got 6 units of 80mm fans blowing (powered by another PSU)... using kingston hyper-x 6400 (spd 1:1, 4-4-4-12 @ 2.0vdimm)... but i lowered it back 333fsb with stock vcpu, vmch n vichio but vdimm at 2.0v spd 4:5 (ram clock at 832.5MHz)... OC at bios... how to clock to over 400fsb with lower vcpu??? can be done??? my oc skill very limited only...

^ic ic.. coz lastime im using the AW9D-Max, highest FSB i can b0ot via bi0s less than 350
if urs can do 400FSB, its should be nice, IMO

if u can get stable at 3.4Ghz at lower vcore, that already nice

hey beastx,

the 69'C temp is at full load? or idle temp?
cause for my setup, at 2.1Ghz only...and idle, the temp is around 60'C already...

and I'm using TAT...so when i start to push the CPU at full load, the temp will go up till about 79 or 80'C...

current setting is 266FSB @ 8x multiplier... if i push my FSB to 333, i'll get 2.6Ghz...but my idle temp is up to 75'C around there...

what could be possibly wrong? or is it the ambient temp at Japan is way much cooler than Malaysia, thus you're getting better temp reading?

i'm using Zalman CNPS9500 heatsink fan btw....

Ambient temperature was around mid teens (12 to 17 C).. now 7 to 12C.. can see your own breath...

It is the load temperature, never exceed 75C...even when room is at mid 20C. Getting all 4 cores passing orthos is a challange... core no3 would give up in minutes... while othe 3 can go to 3.8GHz and above without much fuss. Heatsink Scynthe Infinity.

how did you apply your thermal paste?

what thermal paste are you using?

at 2.66Ghz, my CPU is already at around 75'C for idle...
so it's gonna be a big challenge for me...

then better to change better CPU cooler

i dunno...maybe it's something wrong with my setup...i'll try setup again....

beastx,

when you say load temperature...means u are running prime? or TAT 100% load?

i thk is prime or orthos 100%

all 4 cores orthos 100% load for 8 hours or so..

ok...that's pretty good already...my idle temp is already 75'C @ 333FSB and 2.66GHz speed...

maybe it's chinese new year and hot season in malaysia la...hahaha...
motherboard got fried recently...so will have to wait for warranty return before i can verify further what's wrong with my setup ...

wah lan eh...75ºc u have to be carefull fren...coz its just 333fsb @ 2.66ghz

ur rig can fried anytime... if full load can boil eggs d...

wow, that hot.
I think zalman is ok.

This post has been edited by SEP910: Feb 19 2007, 09:29 AM

helps n comments needed

proc: e6600es
mobo: abit ab9
ram: kingston hyper-x 6400 ddr2 (512mb x 2)
hdd: hitachi 160gb sata2
gc: msi 7900gto (flashed gtx)

setting 1
oc: 370mhz fsb (3.33ghz)
ram: 370mhz (1:1)
timing: 4-4-4-12
vcpu: 1.5125v
vdimm: 2.00v
vmch: 1.25v
vichio: 1.50v





it idle at 41c (table fan + air cond) but 45c (air cond) without table fan.

i tried lowered the vcpu the but the system became unstable n couldn't run orthos. any idea? i'm using running this in my room now with aircond n room temp is 24c. using stock hsf but open side panel n with a table fan blowing directly to cpu. waiting for new cpu cooler!


setting 2
oc: 400mhz fsb (3.60ghz)
ram: 400mhz (1:1)
timing: 4-4-4-12
vcpu: 1.6875v
vdimm: 2.00v
vmch: 1.45v
vichio: 1.70v



at 400mhz fsb (3.60ghz) @ 1.6875 things became nasty. it idle at 50c (very low aircond, room temp is 28c + 6 low rpm 80mm fan blowing direcly) in my ofis. i have'nt try to lower vmch n vichio. this setting passed orthos for 1+ hour but lazy to continue. i wanna know if anyway can lower the vcpu? it's a bit crazy at nearly 1.7v. will better hsf help lowering vcpu?

both setting passed memtest.

to all sifu out ther...! is it normal to go above 1.5vcpu..?

thank u...

IMO i thk ur vcore is a bit high