then u should lower ur OC lor..

my mobo is Abit KN9s..
i dunno how to overclock perfectly..
can u all help me how to overclock safely?

Post up some cpu-z SS,maybe we can help.

Or u can ask bro tapirus,cuz he's using the same mobo like yours.

This post has been edited by ocz: Dec 14 2007, 11:07 PM

oh..i put my cpu-z spec here

http://valid.x86-secret.com/show_oc.php?id=281478

Bro,change the multiplier to x10 and set the cpu freq to 200.

ooppsss..i enabled the cool n quiet...

Oic,try to disable it 1st then u can do OC.
Whats the cpu speed r u running now?

http://valid.x86-secret.com/show_oc.php?id=281826

Now can see d.
Well,have u tried to increased the cpu freq? such as 220mhz x 10? 240mhz x 10?

220x10=can`t boot xp--say something file in xp was missing...
240x10=even can`t start up pc

This post has been edited by User_Xp: Dec 14 2007, 11:44 PM

Allrite,in that case.have u push the vcore?

Put some ss of your ram timings and speed.

i just know the basic only-disable cool n quiet..

em..pushing vcore..ram timing n speed??neva touch that...
dunno the safe limits...

But before you push the vcore,make sure u use a good HSF.its just in case.
As like for ram voltage,you also need a ram cooler or other cooling before you increased the voltage.

But,if u are doing 2.45ghz i dont think there will be a problem.I tried before with only usint stock HSF.

the everest ultimate beta shows that vcore can reach till 1.3V
but i dunno the safe voltage of vcore n ram voltage,timing and speed..

This post has been edited by User_Xp: Dec 14 2007, 11:59 PM

1.4v is enough to pump 2.4ghz d.As for the vdimm leave it 1st.

make sure you loose all the ram timing 1st.It will be more easy to halp if u have those SS.

make sure you loose all the ram timing 1st.It will be more easy to halp if u have those SS.

-can`t understand..

I hope u can provide a ss in detail in cpu-z for the ram speed.
So easy to tell the timings to you.
And also can help you on what to.

http://valid.x86-secret.com/show_oc.php?id=281826

check it out n tell me what to do

Hi All
I have a question (strange one) . I tried to OC the proc staring from 1.34v until 1.61V, most of the time the CPU temp just ideal at 47 degrees on smartguardian. Here is the tread

- 1.34V (temp at 44 degrees)
- 1.37V (temp at 47 degrees)
- 1.42V (temp at 47 degrees)
- 1.47v (temp at 47 degrees)
- 1.50V (temp at 47 degrees)
- 1.56v (temp at 47 degrees)
- 1.61v (temp at 47 degrees)

Using Smartguardian - most of the time temp will be around 46~ 47 degrees ideal, using Speed fan 4.33 will be 40 ~ 43 degrees ideal.

I already confused which one is the correct temp for my proc? I scared I might burn my proc cause my Vcore already at 1.64V.

Mobo: DFI Lanparty UT NF4 Ultra-D
Proc: AMD X2 4200+
Headsink: Thermalright XP90 with 8.5mm fan on top spinning 3000rpm

Any comment from the expert or sifu?

This post has been edited by hellwaker: Dec 15 2007, 12:21 AM

The rest ok d.Just try to increase your cpu frequency.
Increase a bit vcore.it wont harm your rig.

There you will notice your ram speed will increased.

The HT link set to lowest 1st.then later u can increased it.