yes 2.3v IS high considered that stock vdimm is 1.84v ... It will shorten ur RAM life more if u pump it even higher...

Cheapo value chips usually don't respond well to voltage increment, like your RAM. It will shorten the life faster. It's different with chips which overclocks well with additional voltage.

How much did u pay for that Patriot? My cheapo no-heatspreader plain looking Crucial value DDR2-667 overclocks way better than that, at 2.2V only.

TT RM235 ....but in CPU-Z shown could run at 400Mhz 4 4 4 12 at 2.2V and 500Mhz 5 5 5 15 2.3V. Dunno wad SLI enable.

It's either your RAM is crappy, or there's something very wrong with your setting...

Nobody could help you unless you post a screenshot or something.

And I bet you're running with 1T command rate which is holding back your RAM a lot

This post has been edited by soulfly: Dec 30 2007, 12:21 AM

Hope there is something wrong with setting.I will go back and make a SS.

Currently i'm running a pair of Crucial Ballistix Tracer PC2-5300. If i were to add a pair of Crucial Ballistix PC2-8500, all the rams will run at the lower speed of the Tracer PC2-5300 right?

I know there would be difficulty overclocking if different rams were used but will i encounter difficulty overclocking these 2 pair of rams from same line-up but of different batch and designated to run at different speed at stock?

This post has been edited by nvidia: Dec 31 2007, 03:18 AM

Definitely. 4 sticks of rams are more difficult to overclocked compared to 2 sticks. In addition, your PC2-5300 will hold back the overclock.

4GB DDR2 ram fever is in town.
Later you'll see many will post their results of overclocking their newly purchased 4GB DDR2 rams.

Not sure but prefer Crucial. I'm running my Kingston Value RAM DDR2 667Mhz at 800Mhz 4-4-4-12 also

---

Added on December 31, 2007, 10:56 amMy maximum was to go to 850Mhz with 5-5-5-15 timings, if go all the way to 900Mhz get errors from Orthos within 2 seconds already.

---

Added on December 31, 2007, 10:57 amNice, coz you're sellin' all those 4GB kits

This post has been edited by skymyxe: Dec 31 2007, 10:57 AM

can i used 4 X 1gb crucial ballistix DDR-800 with Gigabyte P35 DS3 mainboard?

Should be able to run perfectly without any problems at stock clocks...... I have 1gb x 4 sticks but haven't tried on my DS3 yet....

Wondering why is that. You do have a lot of superb performance RAM's I'd say. If only I can get my hands on Crucial

dude,according ur model num,show at the ddr2 list website

PDC21G6400+LLK / PDC22G6400+LLK 4.0-4-4-12 @ 2.1 ~ 2.2V

Elpida AG-6E-E
Micron D9GMH (B6-3)
Micron D9DQW (BT-37E)
Micron D9DQT (BT-3)

so if u r bad luck.....
get the elpida chipset thn god bless u......

it's between 6E-E or D9GMH

Lazy to try 4 sticks. So far, 2Gb is enough for me......

True2, 2GB is enough already.

Just my RAM's can't go further, so have to wait for high performance or buy ddr2 800Mhz

someone using kingston based on epilda chipset??

2x 2GB sticks?...

Anything wrong with that?

Ya, was asking the same thing too?

What's wrong with 2 x 2GB