when i was doing burn in the temps reached like nearly 70c based on ABIT EQ.

the thing is i'm not sure who to believe now. DFI board reports my A64 on slightly lower temps than my ABIT board.

i'm on ABIT board now, the DFI can OC a bit better BUT when run dual stick 512mb it sucks. i rather have 1GB @184 than 512mb @238mhz.

EDITED : damn i rebooted and it's now running 1GB @234mhz!!! w00t.

please don't tell me to get 1 stick 1GB cos this goes without saying and mind you i don't grow money on trees. thx

This post has been edited by goldfries: Jan 26 2006, 04:50 AM

The thing is, you need to set everything manually in DFI.

So, when you buy a DFI, don't blame the mobo if you're running things at AUTO...lol

Anyway... here's the result after burn-in.....

2800+ (1600MHz) @ 1.35V



This post has been edited by soulfly: Jan 26 2006, 11:41 AM

1600 @ 1.35 is default speed or wut ? sorry i duno much about A64

2800+ default speed is 1600mhz with 1.4Vcore

reduced 0.5Vcore already

1.35v at stock speed.. you're right...btw, soufly, why run stock speed? dun like the heat eh?

ya... just feeling like running at default, can turn fan quiet (even turn off also no problem....stupid noisy UFO!)

hehe...wat is your ufo spinning at? mine is spinning at 2k rpm and temps is bout 50 when doing folding work 39 when idle...Vcore at 1.575v

yesterday i juz done burn in 8 hours 30 minute for my barton sorry abit off topic here oledi but nvm la... nonid open new thread for this simple things eh ? i dun see any improvement vcore i set 1.85v burn at default speed

p/s : i dun think the temps are over 50c even i ran my delta at 5v it stays at 47-48c only i think gotta turn off da fan tonite

dunno what rpm.... after i take off the LED grill, the rpm seems to be not reading anymore.

but with SmartGuardian, fan speed control set at 84.... with the current setting, full load at 40'C, idle at 36'C with the system temp at around 44'C.

This post has been edited by soulfly: Jan 26 2006, 01:11 PM

soulfly, u use the lower vcore burn in method or higher vcore like cyclone87?

hell my sempron at 315fsb, i run pi 1mb, 8mb, 16mb, 32mb, then burn in 18hours, running 3dmark06, no crash at all, but it jus failed within second in sp2004....
should it be consider stable?

alamak, tak habis habis. i hope you're not referring to me cos.............

sooooooooo many times i've already stated for the past pages - I SET IT MANUALLY.

both DFI and ABIT i set manually, with same settings one works with dual-sticks and one doesn't. you know, i wouldn't be so dumb to accuse DFI of not working properly without actually trying manual settings.

U sure u already tweak the alpha memory settings in the bios? AFAIK... Abit mobos dun have these kind of thing.

Give me your full bios setting, the most stable and the highest speed. I help u tweak until DDR600 with 1T... lolz



This post has been edited by soulfly: Jan 26 2006, 05:59 PM

yes. i would appreciate it if someone could help me out with the DFI memory setting.

but see, that's the thing. if i have to fine-tweak the DFI's details to make it run like my ABIT - then forget it.

since the ABIT providing me what i wanted already - then i'll stick to it. save time. the DFI will run as 2nd righ with S64 2800+ 1 stick 512mb.

lol u r not a truly OCer arent u?
y dun giv it a try, maybe it wil run exceed ur expectation!

i couldn't care really.

2.5ghz@1.5vcore on Scythe Ninja fanless doing F@H is pretty nice to me.

This post has been edited by goldfries: Jan 26 2006, 09:49 PM

just got my nf8 and s64 2800. sadly, it's "Made in China" one, with LBBWE 0545. Now, the technical question, how do i change the multiplier? right now, i only using clockgen, and able to bump the htt to 310 at 1.52v. FSB:DRAM is CPU/10 at cpu-z. really noobie in this sc754 oc. . n my temp, it stay at 30c whether it's 1.6G or 2.4G. But will "JUMP" ( not increasing gradually ) to 37c during SuperPi ( 38.44sec ). After it finish calculating, it jump back to 30c. Is this normal?

S64 can't change multiplier la.

ehehhe.... dunno lah bro. i just now, baru pakai s64 ni. . so to oc, just increase the htt?

yup and no... bsides bumpin up d fsb, u cant care less foor d ram speed.. so, alway make sure wats d speed of ur ram...and of course d ram timing in order to get d most stability to ur system.. ermm.. u better see dpinned thread for newbies..

i recommend u not to use clockgen as u already can change d htt at bios... jus my 2 cents..