cyclone87, u use icute450 twin fan to OC? will it stable?

u make me wanna keep my icute

btw there is nf8 n nf8-v, nf8v seems cheaper n support raid, will it hv a big difference in OC?

my epox 8rda+ kong edi, if cant repair hv to switch to s64 to suit my budget n OC needs

btw izzit s64 3000+ & above got cool n quiet tech oni?

This post has been edited by wtm0325: Aug 30 2005, 03:31 AM

btw when will s939 sempron come out? will it better than s754 a lot?

i think it's about amd64 3600+ oni, using amd universal tools to calculate...

sempron is 10-15% slower than amd64

This post has been edited by wtm0325: Aug 31 2005, 04:33 PM

want to ask kucingfight n cyclone, u both set ht transport volt n ram ref to max?

i encounter a problem, when running 265fsb with 166mhz ratio, i found my agp change to 99 even though i set it to 66, any setting i missed?

btw the ldt should set to 8 bit or auto? pls help, i cant OC my rig stable now, eventhough i get 0528upmw, i doubt mine is bad chip

lastest news, i did this before i read u all reply...

i set ram, ram ref, chip n ht volt to max, n i already flash to the latest bios when i first start play with it

at ram divider 100mhz, i able to hit 331ht (below ht 1k), it's only benchable but but not prime stable...

at 133 divider, max ht only 295, no matter how hard to push or play with multiplier, it'll nvr over 298...

at 166 divider, max ht is the same 295ht, n cant push to higher oso

i nvr adjust vcore as i think more on mobo fault, the proc seems fine running very well, still nvr over 40 so far...

guys lets say 2650 @ 166mhz vs 2360 @ 230++ mhz, which 1 will be faster?

i'll try cyclone way to oc it again, btw cyclone ur htt multiplier is 3? n how to adjust ram ref volt? dun understand wat it means...

ha yup agree with it, maybe can buy a cheaper nf3 mobo if no OC n buy a gc, i'm sure ur sis wan to play games much

cyclone, i'm now only able to do at 2340 (292httx8) @ ram 234mhz stable from cpuz, but when i run memtest it showed 242mhz in stead of 234mhz?

i cant go higher as i think my d43 max out at 242mhz 3-4-4-10 @ 2.8v at memtest, i'm using 166 divider, i tried run 133 divider but also the max htt will be 295htt dunno y, then better swith to 166 divider

cyclone, i found my system restart slower after OC, when restart hv to wait for a while, if shut down n turn on no pro, did u face the same thing? now my volt is like urs, only vdimm n vdimm ref is adjusted to max...

i now enable system bios cacheable, i heard it'll lead to system unstable but faster, how should i test it? use memtest or cpu test?

wah then ur agp/pci is how many mhz now?

yalor, even nf8 also when restart it my liteon combo always running for bout 10-20s before start, is the lock cant be trusted?

thts the ram problem rite? try to lower down ur htt lo...

btw anyone know how to calculate divider? my cpuz showed my ram was 234mhz, but memtest showed 242, izzit somethin wrong?

n i found my nf8 less 4 capasitors, how bout urs cyclone n kusingfight? i doubt tht might limit the OC capability

This post has been edited by wtm0325: Sep 5 2005, 01:51 AM


Attached thumbnail(s)

curious bout mobo, how high htt can go? coz msi mobo seems cool, last few when choosing mobo it's in my list oso

n i did calculation on my mobo divider 200:166, 292htt/200x166 should be 242mhz on my ram, but my cpuz & other software like sisoftsandra n everest shown 234mhz, izzit the mobo pro?

This post has been edited by wtm0325: Sep 6 2005, 02:47 AM

o.... thts y i oc till 2.34ghz n my ram shows 234mhz

btw y i run memtest for the stability, the memory show 242mhz? so which 1 to follow?

ha now oni i know the stepping meaning, if know earlier might go to get the A in LYP anyone using A/B one?

btw so far only had tried my proc, max squeeze out is 330htt on 2:1 divider at default vcore

malaysian, i doubt the memtest give the wrong result

mine is M, purposely find the same code as cyclone, think tht tht code is the best

0528 UPMW

ahahahaha dun spam la...

yup

but sometimes not, 3-4-4-8 vs 3-4-4-10, maybe the later will end up faster, thts when i run benchmark last time, correct me if i'm wrong

dunno le, hv to benchmark n c, almost the same i think, not much difference

sure it'll run faster for lower timing, but u must had a good ram oso

hehe maybe abit mix up their picture, btw mine is nf8, not v2

cyclone, i'll do tht after my exam next week, the rig is at hometown, thank for ur advice, hope tht will let me push up to ur result

u set put ur ram setting to auto? thts my case last time, i only able to push my proc to 250fsb when set ram to auto, after tht when i set it to manual setting, i can push it to 292htt now stable, will push it again next week

try to set the ram timing to default speed using manual setting

wait for soulfly, he owns the same mobo, he might help

kucingfight did u tried using 1 stick of ram 1st? maybe 2 stick limit it le... u r running 166mhz divider rite?

hehe can share ur experience when u used p4 2.4c last time with sempron here ar? feeling after OC n default speed very curious le, hvnt tried out p4 C ht before n after OC