hmm...you need to change the ldt multiplier as well

ram bandwidth is not important in K8 processors.

higher speed may give you wonders in memory bandwidth benchmarks.... but in overall system performance it does not give any much advantage at all. the most important is clockspeed. in this case, lower latency ram will help better.

only Sempron 3000+ and above can change multiplier.... 2800+ and below cannot.

yaa... i used 3x, divider 166, htt 310. full speed is 2480. It's my ram limiting me, since the vdimm onli 2.8v. Mine run best at 2.9v. . But, when i used divider 133, my system wont boot, just beep. why ah?? timing is manually set at 3-4-4-8

on certain dividers, you need to change the Tref value in order for the divider to work

plan to run sempron 3100+....erm....any 1 try it b4?how high can 3100+ go.wohahahaha....i know the multi is 9X.should can go over 2.7ghz lor...

try 2x.

RAM divider you may need to try 150 also. btw what RAM are you using?

EDITED : the one on your siggy?

This post has been edited by goldfries: Jan 27 2006, 12:34 PM

Yea... the one inmy siggy. 150? i dun think nf8 has it. just 100 133 166 200 and ldt 1x to 5x.

no, i mean the RAM
[MWTS] 1gb 1 Stick BT-D43 DDR400 ( 2.5-2-2-2-2T@258 and 3-2-2-8-1T@253 )

my BT-D43 can do like 230++ if needed.

mine can do as my siggy but onli wif 2.9v. now, at 2.8v its 248 max. over that, bsod.

suggest u dun use 150 divider(hehe wtm tel me one), i tried it, it wil limit ur OC even though ur ram stable
sempron mem controller r quite picky

nf8 din have 150. btw, i tried 133 divider, but when boot to windows, check wif cpu-z, its back to default speed; 200 x 8.0 ? y?

on my case last time 150 divider doesnt work stable for me will i dunno, maybe different people different case

lol last time i hav this prob, when fsb exceed 327, dun hav method to solve except OC using clockgen

never try never know. there were a few times where i had to use 150 but normally my memory works fine with 166.

maybe u r rite, but if u hav choice dun use tat, strange divider wil giv prob, in my case
anyway soulfly u run ur proc at 1.63V all the time?

yerp.... previously running my cpu 2.7ghz at 1.638V on 24/7

but currently running everything at default speed only with 1.35V for the cpu

Guys, need some help here. Just finished playing, tuning, finding the best for my s64. Quite satisfied wif 315 HTT. Using divider 166 3-4-4-8-2T, i cant get 3d to stable. Not even 3dmark. testing wif 248 3-3-3-5-2T, i can play any games. Increasing the vAGP oso didnt help. Increasing the agp latency to 67, oso no good. Is there any thing i miss-out to change? My temp, quite suspicious la. at 2.5G oso 30c idle 41c prime load. Using 1.58v on vcore. wat ur guys temp? Is it s64 low on temp?

yea s64 low on temp.
try use lower divider see if ur proc can go higher
maybe ur ram hit the wall\
btw 315 stable prime/sp2004?play game dun indicate stable, in som case it wil fail instantly in prime.
1.58V is quite high...too high may oso limit OC, coz too hot, 41C i think not accurate la, mine use TT beetle 1.55V oso full load 44C

This post has been edited by superpc: Jan 30 2006, 06:26 PM

i can sp2004 for 3 hours, superpi oso can finish. dunno y in 3d cannot use divider. well, back to 1:1 onli choice.