CPU-Z 1.57.1-updated 20.04.2011
http://dl.dropbox.com/u/4668167/cpuz_1.57.1.zip
Sandy Bridge Overclocking V1, 2500K/2600K/2700K | LGA1155 P67.Z68.Z77
|
|
 Apr 21 2011, 11:28 AM
|
 
All Stars
18,503 posts Joined: Oct 2007 From: P.Jaya 
|
|
Quote|
|
|
|
|
Apr 21 2011, 03:38 PM
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor 
|
All sifu, 78c full load count as safe? Under Hyper 212 Plus on 4.8 GHz...
|
|
|
Apr 21 2011, 03:55 PM
|
 
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan 
|
QUOTE(Liuteva @ Apr 21 2011, 03:38 PM) All sifu, 78c full load count as safe? Under Hyper 212 Plus on 4.8 GHz... Still acceptable u would start to worry only when it hits 90C   |
|
|
Apr 21 2011, 03:56 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
4.9 GHz with 1.35 V set in bios and 88c full load, anyway whats the safe temp for it? Below 90C?
Added on April 21, 2011, 3:58 pmLinX now, on 6/21... Reply via phone btw. This post has been edited by Liuteva: Apr 21 2011, 04:15 PM |
|
|
Apr 21 2011, 04:07 PM
|
|
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
Most mobos are set to shutdown automatically at 100C.
Ur proc is actually protected; unless u turn off in BIOS settings. |
|
|
Apr 21 2011, 04:08 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
Oh ok... 13/21 now, temp never exceed 88C still. I think I cant play with 5 GHz...
 This post has been edited by Liuteva: Apr 21 2011, 04:15 PM |
|
|
|
|
|
Apr 21 2011, 04:16 PM
|
|
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
QUOTE(Liuteva @ Apr 21 2011, 04:08 PM) Oh ok... 13/21 now, temp never exceed 88c still. I think I cant play with 5 GHz... Yes i'm absolutely sure that 5GHz is not possible on air cooling in non air conded room here eventhough u got a good chip.My new 2600K requires low vcore but releases heat worse than the previous one. |
|
|
Apr 21 2011, 04:23 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
From ur opinion, I own a good chip or not? It's MY one.
Added on April 21, 2011, 4:44 pmi7-2600K, forgot to mention. This post has been edited by Liuteva: Apr 21 2011, 04:44 PM |
|
|
Apr 21 2011, 04:47 PM
|
|
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
4.9GHz below 1.4v vcore during load is a good proc.
Just that it seems to produce a lot of heat. There are two types of chips in general: 1) low vcore, but high temp (hot) 2) high vcore, but low temp (cooler) Ive noticed these since Bloomfield. This post has been edited by owikh84: Apr 21 2011, 05:04 PM |
|
|
Apr 21 2011, 04:54 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
1.49 GHz?
Added on April 21, 2011, 5:08 pmWhat is "CPU I/O Voltage"? This post has been edited by Liuteva: Apr 21 2011, 05:08 PM |
|
|
Apr 21 2011, 05:10 PM
|
|
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
4.9GHz editted lol was confused with underclockings.
Added on April 21, 2011, 5:13 pm QUOTE(Liuteva @ Apr 21 2011, 04:54 PM) 1.49 GHz? Vccio = vttAdded on April 21, 2011, 5:08 pmWhat is "CPU I/O Voltage"? Pls refer to page1 glossary This post has been edited by owikh84: Apr 21 2011, 05:13 PM |
|
|
Apr 21 2011, 05:16 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
Ok. What should I put for that? Current set to "auto".
|
|
|
Apr 21 2011, 06:34 PM
|
|
Elite
8,711 posts Joined: Nov 2007 From: Butterworth, PG / Machang, Kelantan
|
QUOTE(owikh84 @ Apr 19 2011, 11:32 PM) as for VCCIO aka VTT, most of the time u wont need to adjust it at all @ 1.05v. U might need to increase it a lil bit when playing with higher RAM speed & tighten timings etc... Using over 1.2V should only be necessary if u're pushing the proc toward 5GHz +. Like one of my proc @ 5GHz needed at least 1.2v VTT to boot into windows. Using above 1.4v is not recommended at all - u have been warned! |
|
|
|
|
|
Apr 21 2011, 06:46 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
I tried 1.15 V, and my temp seems to increase like 4C to 5C. Now I set back to "Auto" with temp of around 90C.
Added on April 21, 2011, 9:19 pmWhy during full load the voltage will increase? This post has been edited by Liuteva: Apr 21 2011, 09:21 PM |
|
|
Apr 21 2011, 09:50 PM
|
Junior Member
404 posts Joined: Jan 2009
|
voltage increase due to you enable PLL function?
|
|
|
Apr 21 2011, 09:53 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
Internal PLL Overvoltage? I disabled it.
|
|
|
Apr 21 2011, 11:01 PM
|
Senior Member
2,295 posts Joined: Jan 2005 From: Penang 
|
QUOTE(owikh84 @ Apr 21 2011, 04:47 PM) 4.9GHz below 1.4v vcore during load is a good proc. original review says stock cooler can OC to 4.5ghz, I guess after Win7 SP1 + latest Linpack, its impossible anymore.Just that it seems to produce a lot of heat. There are two types of chips in general: 1) low vcore, but high temp (hot) 2) high vcore, but low temp (cooler) Ive noticed these since Bloomfield. I downgrade my cooling when go sandy bridge, now pawned  |
|
|
Apr 21 2011, 11:16 PM
|
|
Senior Member
2,991 posts Joined: Jun 2007 From: Johor
|
Daily usage impossible all cores 100% right? Just normal gaming...
|
|
|
Apr 22 2011, 01:23 AM
|
Senior Member
3,795 posts Joined: Nov 2008 From: Varies....
|
ok..done with eco
2133 cant even stable on loose.. this the best i can go 
any subtiming shud i consider changing? |
|
|
Apr 22 2011, 09:03 AM
|
Senior Member
2,265 posts Joined: Aug 2006 From: Damansara
|
I change multiplier from 31 to 34 so i dont have to worry anything am i right?
Mine is i5 2400 btw. |
|
Topic ClosedOptions
|
| Change to: |  0.0293sec
 0.47
 6 queries
 GZIP Disabled
Time is now: 4th December 2025 - 09:34 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.