might be and might not..
but cuz i can say 26x is too low..i think most value ram can handle..
when we talk about >300htt then yes, perhaps we need high performance ram..


take a look.. a KVR can do just fine..

this is nice.
DDR2 667 5-5-5-15 ram at DDR2 800 4-4-4-10 speed.
but how about the dram voltage for this?
and what is the software that show all the dram timing there?

800 4-4-4 is not a wow i guess bro..

btw, it is CPU tweaker.
u can use AOD also, i like AOD more cuz its richer (by few only ) but the only turn down is applying the setting takes some time..

dram voltage is per AOD.. mem vddq.. 2.75v (i believe i set 2.1v in bios.. not so sure, old SS )

haha, but for me, it is.
but DDR2 value ram can stand 2.1v? and without active cooling on it.
some overclocking guide state dram voltage is most sensitive voltage among them.
improper use of it will result in burning dram chips.
so i usually didn't touch dram voltage,
and don't know how is the safe way to play with dram voltage.

well.. depends on the ram chip itself..
u touch it, if not hot, then ok..if hot..then not ok..

in my case, 2.1v is very2 ok,but max i will go for daily usage.. not like our risk taker.good tweaker sir antonio.. set his ddr3 to 2.4v iinm

1 ram that i know is hot is tracer.. with d9s inside.. but some models have rated voltage 2.1v..so still i think even its hot,it can stand the heat and the vdimm..huu

if u afraid getting ur sticks killed, so better not.. make 2.0v max.. btw, ur KVR using what chip/ic?

i see.
hmm, i didn't really pay attention to the chips.
later when i clean up casing only see la.

Hello friends, sharing some results of my overclocking.. Not very impressive though, however I am very happy with it.

AMD Sempron 140@Unlocked | 3.6GHz | suhuann | MSI 785GTM-E45 : BIOS v8.6 | Crucial DDR2 | 1068MHz | 5-5-5-15 | Cocage MST-140





This post has been edited by suhuann: Feb 18 2011, 10:46 PM

nice overclock there.

would like to ask if I'm doing things right, a tiny oc, but somethings not right with the ram setting, it says I'm running 1465 speed. I've post some value can anyone check if things is right? tq



This post has been edited by moorish: Feb 20 2011, 11:15 PM

1st, use CPUZ cuz that is the software everyone trust..

and if the value there correct, yes..it runs at 1465mhz..
with 1333 divider..

so what does it mean?
I'm doing it right?
I'm doing it all wrong?

220MHz x 10/3 = 733MHz
equivalent to DDR3 1466.

Don't worry ur doing it right, its normal when u oc using a multiplier lock cpu, when u raise the bus speed/htt speed ur ram would be overclocked as well..

Now I upped the the frequency to 230 x 15 = 3450
But I lowered the ram to x5.33 = 1225

Will it be better?

If u just wanna oc ur cpu, sure that would be good, u won't put much stress on ur rams
Keep ur HTlink speed 2000mhz & below tho, u won't get any benefit from high htlink speed, in fact it can cause instabilities in ur oc if u went overboard with it

ok I'll try to find a way to do that

Just change ur HTlink multiplier to a lower multi

now the setting is

CPU 3450 - 15 x 230
FSB 230
memory 1225 - 5.33
HT link 2075 - X9

I heard AM3+ coming

Seriously bro? AM3+ mobo or the cpu?
Gip some preview if u got them in ur hands eh?