this is the best stable one that i can do with 3.5Vdimm
not dare to do more ...
http://valid.x86-secret.com/show_oc?id=19744

kinwee, yours one got any active ram cooler or not ?

This post has been edited by ray99mond: May 26 2005, 04:36 PM

Air cond room leh tai ko....



That was taken from my old 3200+ winnie everything at stock with KVR in the same room with my PC with VX gold.

Can you lower to 3.4vdimm for that 250fsb ? 3.5v seems to high for 250fsb.

What TREF are u using ? I suggest u to try 1168. It's best for my ram. Also set the Idle Cycle Limit to 016cycles. This is best for UTT and BH5 ram. You might be able to do with 3.4vdimm after setting these.

ok.
I'll try it later

kianwee, any other tccd setting that can do 300htt stable? i tried so far none of them stable.. and i dunno which one to tweak.. to many settings lol

300mhz fail memtest after a few secs

now i'm running at 285x9.5 = 2.7ghz

and what is the diff between 270x10 n 285x9.5? i mean why cpuz still detect my ram at 270mhz eventhough i set 1:1 285htt

This post has been edited by irenic: May 26 2005, 08:20 PM

now this is just ridiculous.. dfi ultra-d but not proc, gfx card or psu..


Attached thumbnail(s)

Lol, get venice from robyncom.

Try this:

In DRAM Configuration Section of Genie BIOS:

200
enable
2.5
04
07 or 8
03 or 4
07 or 8
16
03
03
02
03
4708, 3120, 0648, or 2560 (4708 works well at high overclocks)
auto
enabled
auto
0
level 6, 5 or 7 (6 is normal, 5 or 7 are weak drive strength)
auto or level 2
7.0
auto
256
disable
16
07
disable

In Genie Bios:

270
4
16 16
7
100
disable
1.500v
1.300v (This is about 1.57v, if you need more or less adjust, but do not go past 1.45v here, use more the 123% below, there is a reason )
above VID * 123%
1.30v
1.70v
2.8v (2.7v-3.0v may work for you)

Let me know how it goes.

getting 3700+ sandy from dinster already

can u guys help me choose either one of these?

OCZ PC4000 Gold VX CH5 chips 250mhz 2-2-2 at 3.3v (Rm890)

or

OCZ PC3200 Gold BH5 chips ~240mhz 2-2-2 at 3.2v (read most reviews hit this particular o/c) (RM680)

for me i will go for OCZ PC4000 Gold VX CH5 chips 250mhz 2-2-2 at 3.3v (Rm890)

thx .. i will try tonite.. hmm what's the reason for the vcore trick?

I mean get that venice from robycom while waitin for 3700+. you could use that venice is spare.

Get PC4000

thats a good idea.. then when the san diego arrive, sell to me the venice cheap2

hahaha unfortunately i dont have the moolah to get a spare proc at the mo

thanks for the suggestions guys, i made a typo earlier on, the pc4000 isnt rm890, its rm860.. so a bit more appealing now

got ur oledi
still waithing for mine to come

gavlim COD in penang mah....

coz multiplier 9.5 will run your memory on divider
* all .5 multi will run memory on divider

285x 9.5
memory speed = 190/200 x 285Mhz = 270.75MHz

wow very nice... congrats

i know le..hehe
hope mine come tomolo..got lots of thing to do

anyone try samsung tccd for cl1.5 ?
can it run ?
hwo about winbond bh5 ?

tictac
THX

This post has been edited by ray99mond: May 27 2005, 12:41 AM