mc make me feel boring

2 core sweet spot for now.. 1.136V @ X2 @ 3.1Ghz
[attachmentid=1118142]

HyperPi
[attachmentid=1118143]

x aci mah... 4830 vs 4870...

btw, stop playin games n get ya @ss on ya chair & start oc ya ram bro...

i need to know how far our ram can go...

Miahahahaha, right now baru main2 skit with the timing, i'm surprised too see that these KVR's can set good timings 7-7-7 at 1.62v

aiyo... vsync sure off.
benchimark of SF4 can get average 70fps (but the jungle arena one...the FPS drop...)
i pretty amazed by 4830... no one will recommend this GC to use on 1920reso...but it doing well for me...

tu la... double the performance double the price..wakakak

and i havnt get my ram yet..impatient edi... ask the seller no respond..

oi oi...maju nmpk...
70FPS on 1920 reso?nice..

with heavyly OCed GC... if no OC at all, the game sure hampeh semacam je...

@ah_kho...ya..did bencmarking with 3.6ghz (fully stable setting) vs 3.1ghz...no significant FPS gain..
ure right...then i think it will be better to revert back to stock speed with lower volt...

gaming, can't really see... unless u do image editing, rendering.. ;0

Overclocking Session.
Here, 3.2Ghz @ X2 @ 1.136V
Temp : load - 50 degree celcius

[attachmentid=1118808]

HyperPI
[attachmentid=1118810]

Test
[attachmentid=1118813]

CineBench
[attachmentid=1118837]

This post has been edited by xixo_12: Aug 4 2009, 08:12 PM

Perghhh melampau tuh nak test stability smpi pkai cinebench
Nice volt there

My proc gives out after 90 passes of LinX. Heat is under 60C, and upping the vcore doesn't solve the problem. What else can be done to make it stable?

post ur ss here main and memory tab
let others help u..

nice there xixo...
fuhh....
my LCD s*** even vsyc on..tearing FX still there...
anyone had push crzy valu of NB freq on PII? just like TS did...

My humble OC...



In the middle of another LinX run, increased the NB to 2400MHz for testing.

Update:

Changes:
1. Boost NB Speed to 2600MHz.
2. Switch to Ganged mode.



P/S:
1. 3900MHz (1.5v vCore) -- Stable for 30 mins. BSOD.
CPU Temperature reach 62degree.

2. 1600MHz CL7 ram -- Failed.
vDimm pumped to 1.8v

3. 2800MHz & 3000MHz NB Speed -- Failed
vNB pumped to 1.3v

-pWs-

can tell me what are these 3 temperature are??




Attached thumbnail(s)

bored...
so want to play x4..
change HT to 1.6ghz and ACC -2%
boot like usual....
prime...but 2 thread only...

paiseh..the bios...i reverted back to official bios after playin with x4

so then i get this setting with +12% ACC
huuu...almost same as xixo..but the HT lower cuz want to unlock at 1st..but fogot to change back..


this ACC really works...at -2%..it will fail within seconds...

-pWs- seems u have fun playing...

This post has been edited by kuntawakaw: Aug 5 2009, 02:29 AM

@colinwong..
that vcore is massive edi...cut it..
im no pro to give advice but i obtaind the same speed with lower vcore


@yvliew
i guess tmpin1 is ur proc (since i quite close to core stemp)
and tmpin3 is mobo NB temp... said to be safe at 60c (Depend on mobo mebbe...-my stock/idle at 60.. but mod some fan..drop abit)

i guess la...

and till now i donno what is the other temp..tmpin1..anyone?

edited...i tot the tmpin# numbering same like HWmonitor one..0,1,2....AOD starts at 1....

This post has been edited by kuntawakaw: Aug 5 2009, 02:35 AM

If I'm not mistaken, that usually states the mobo temp probes...

what is TMPIN3 ? its pretty high on 42C ... anyone??

No probs kuntawakaw, any advice is appreciated

So far that's my setting to get Prime stable, haven't tested going lower yet. I also heard that Phenom IIs don't really like high temperatures, so I plan on cutting the voltage down right after I get my overclocks certain. Or maybe you're just more lucky than I am

So far, done 56 LinX passes at the toughest settings possible, and I'm aiming for at least 100 passes. Sounds excessive no doubt, but I'm the kind of person which stability has no compromise

I want at least an X3 as well, I'm sure that my PC can use the third core but the BIOS shuts off the good one instead of the defective. Searched the whole day for info but nothing at all

edit: Why doesn't CPU-Z detect your processor model correctly?

This post has been edited by colinwong89: Aug 5 2009, 03:03 AM

coz CPU-z detect 550BE as 2 cores only..when u unlock to 4 core..it will not recognize the proc model..

to be exact it depend on bios version... if have update on the bios, it will have a name....