Primming for it bro!!!!!

So what is the mhz I should get my ram to be at? under 800?

puff....ssssst....disusuli bau hangit


u need to determine ur max ram speed la. no one knows..ur ram + ur system
and just use the 400mhz divider in order to seek for max core speed

@-pWs-
dare to prime? hehehe...
that good enough.. the last i can boot is at 3.9..4.0ghz is not achievable for me.. mebbe have luck on the ddr3 mobo after this..

how to determine my max ram speed?

here's another window.....




Attached thumbnail(s)

Prime failed even vCore over 1.5v.

Will rest a while. Continue later.

@chewchew
What you want?

-pWs-

prime 10min no fail (small FTT).... at 3.05ghz.. but in OCCT failed within seconds..... trying CPU:LINPACK now...

p/s : how come OCCT shows my Code Name is : Deneb and in CPUZ shows Heka?

This post has been edited by yvliew: Jul 29 2009, 03:33 AM

seek for guides.. 1st page have plenty of them..
lots of things to be learned ya.. me also tired edi learning.

erk.. u have guts to do prime at 1.5vcore?
its nice to see u play with AMD sir.. play hard clock high..wakakka

@chewchew

---

Added on July 29, 2009, 3:34 amit means ur ram is not stable.. either to loosen the timing, or increase vdimm or just choose lower divider..thats all..
i suggest u to choose 400mhz 1st..later after max cpu obtained then tweak RAM...

This post has been edited by kuntawakaw: Jul 29 2009, 03:34 AM

400 where it shows on CPUZ?

The same place.
But the figure should be 200MHz.

-pWs-

X4 B50 Priming initiating....Time to live : 5 Hours

Program: Orthos
CPU: AMD X4 B50 7.5Mb Cache
Motherboard : Asus M4A78-E
BIOS : Official Asus 1208

Voltage CPU: 1.350v
Temp CPU: 45c (approx)

Status: Priming

Still failed even in 1.53v.
Guess 3.6GHz is the sweetpoint for 24/7.

-pWs-

4ghz is too tough unless getting some golden/diamond chip

i can go 3.8 24/7. haha. but the vcore abit high T.t

Yeah bro.
Only manage to finish Test 2. Running Test 3 then BSOD.

-pWs-

if 3.750 Ghz will need 1.440V if its my board.
give it a try. play with HTT help reduce vcore abit.

as long as d load temp is within d comfort zone it's acceptable, but this is very subjective matter for sure.

ok, i still can swallow this...

but this is too just too much...

seriously bro, < 1.4v for a 3.8GHz quad core, that's simply awesome...

do try out diff acc value, u mite able to push it a'lil bit higher... well done, u've made me proud...

woot, can use ah? i remember tryin it on 790gx a2+, a no go iianm...

aod never stress system as much as p95/occt. it's way too lightweight imo.

i'd be dead happy if my chip can do 3.8GHz w/ < 1.4v.

can do me a favor ah bro? try to play w/ htt oc around 270~280ish, see whether u manage to get it prime stable. u got a gud pair of ram there which mite help. my sucky el cheapo kvr can't do > 710MHz @ when htt around 26x...

This post has been edited by ah_khoo: Jul 29 2009, 09:27 AM

nais bro.. wat bios u use??

lol..hard to get stable at 4GHz..even my chip too..
all i can get is 3.7GHz stable 1 hour..that is on 1.5v..
AMD is very2 hard...

wow.. these chip so good 1 and nice temp
i only can get x4 3.4Ghz at 1.35vcore
both use ddr3 and mod bios? hmm...

This post has been edited by under18: Jul 29 2009, 09:56 AM

if u think BE chip is hard, what's more playin w/ high htt oc?

more like d wall is hit usin air coolin, there's not much we can do bout it unless d chip is put under cold.

same as yas (0922cpmw), ddr3 platform does require less volt in gettin high clock. check bro -pWs- oc vs sir antonio's oc. board mite be a factor too...