kalaw saya... nk oc htt lbeh2, nb kene usik. tp saya pakai proc lame...
kalaw htt nk atas 290, kene nek nb 1.3..nk 305, kene 1.4v..lebh dari tu,xle..310htt boley boot...tp xstable..
..er...
http://forum.lowyat.net/topic/1040419
tmpt da dekat..ade sape2 nk suro aku cod kan? huhuh..bayaran,bg aku pakai 2hr.

Athlon II X2 new die or what? wonder which part they improve.. look at benchmark, it just a little bit better than previous athlon at same clock speed

@kunta
nk test Deepcool ka?
need to OC NB in order to get more BUS speed or multiplier?

nk test je...xmaw beli... mcm2 lg nk pikir slain dr kooler

ok..this is what ive been told...if my memory serves me well,
u oc htt,means oc mobo also right? nb is part of mobo...so, to increase the tolerance of mobo to higher htt, need to increase the volt..
if use multi, mobo is not involve in the oc.. so no need to increase nbvolt... <---------------correct me if im wrong.but this is what i learned here

hey ya guys....wat is da best tools to overclock GC? off topic

kuntawakaw u did this test using ur TA790GX mobo ker??

---

Added on June 5, 2009, 11:05 am

I like to use rivatuner or ATI tools..

Whenever one is talking about the North Bridge (NB) of a Phenom II, it is safe to assume that they are talking about the CPU-NB. The CPU-NB is a section of the CPU that controls the L3, Memory Controller and the Hyper-Transport (HTT). As mentioned before the CPU-NB and the HTT have different multipliers, please remember this.

When you overclock your CPU, the higher you go the more likely you will need to stabilize the CPU-NB. What do I mean by this? As the CPU increases its speed to calculate data, so must the speed of which the CPU communicates with other components on the Motherboard: chipset, memory, etc. Let me take the classic example of a 4.0 GHz 940BE and its CPU-NB. If you were to leave the CPU-NB at 1.8 GHz stock then the data calculated by the CPU would create a bottleneck and thus resulting in errata errors or CPU errors. So in order to balance these speeds a CPU-NB clock of 3.0 GHz would be needed. In most cases of high OC’s that result in crashes; the CPU-NB is usually the culprit.

I have constructed a table at which your CPU-NB should be at with ‘Y’ CPU Speed. Please note that there is a +/- 200 MHz difference for each step. In order to find your speed without my table, you can use my formula: CPU-NB Frequency (+/-200) = (CPU-Frequency * 2 ) / 3.15.

can it save da setting permanently?

this is wat i mean..

Yes u can just save the setting in the profile so that everytime the pc start it would auto o/c it back according to ur profile..

---

Added on June 5, 2009, 11:13 am

Hmmmm this could be the culprit of me not having a good o/c..

kuntawakaw u did this test using ur TA790GX mobo ker??

---

Added on June 5, 2009, 11:05 am

I like to use rivatuner or ATI tools..

this is wat i mean..

yup2.on my ta790gx 128
i fail to place my nb8 cooler,so use the stock hs and place a 80mm fan on it.. so even 1.4,it hardly get 40c...
80mm is stick to the nb hs, and another cm90cfm at the side panel,also helps the cooling.

y just dont use ccc? and last time i use rivatuner,i cant set the profile.and atitools nvr work for me.. if i want to clock higher then ccc limit,just use rbe...bios flash it...easier for me..
huuu..i donno this..im using old chip.. u do reseach then u teach me a ventri...but for old chip, i guess my statement is right

wow... it's my lucky day...
thx for the reply, cdlim..

so i think it's better i jz stick to my 6000+ now, and play2 with 9150e then... coz oc the proc to max seems kinda hard for me...hehe..

:/D
ive run a lot of program behind..b4 this use X2 3600+..still no prob..lol..

@gathering
who gonna go?
there is 12 ppl only go so far i know..need more ppl..coz to cut down the LN2 price.. :/P

but sometimes when i wana switch/open the programme at the background, it will delay a lil bit.. mayb there's something wrong with my tweaking.. :/sweat:

for the gathering, too bad i cant go as im now at kedah.. if not i also wana go learn from u guys... :/D