@tkh_1001

pm me msn lai

haha...well...my PC got BSOD...luckily its gigabyte with dual bios...so it didnt loop reboot (not like my older MSI board) and i was away when that happens

guess that 1.4v is the sweet spot...but heck..i think one of my ram just died

edit:

ohhhh u mean 4GHz ram???

This post has been edited by cdlim87: Jan 7 2009, 02:07 AM

nah...it is @4ghz...see properly..his CPU load is @6% multiplier is 6X(in C1E halt/idle)

guess he took the screenie after the stress test

lol.. i saw that late also..

pie_86/Sunbeam CCF/Tuniq TX2/ Intel Core 2 Quad Q6600 @ 3.2ghz (35% Overclock)/1.33v/ Stock Fan/ 35c/ 65c/ Non-Airconditioned/ Prime95

mayb going to change my cooler.. what the best currntly? between ttbt vx n ccf?

if you want something cheap....you can try xigmatek S1283 (should be RM145 and below)

dont really like the PWM fan mount on the CCF...its slides around

---

Added on January 7, 2009, 9:14 amwhy not try fsb:ram 1:1 (set ram multiplier to X2) can go higher ...but temps beware

This post has been edited by Bonchi: Jan 7 2009, 09:14 AM

its my bad... sry bout that...


depend on u which 1 u like... CCF really working quite good... and worth for its price/performance ratio..

ccf arrr bro...dont want to poison ice blade ke?

its c1e and EIST at work at la bro.................

but not bad huh for an old and oudated cooler.
later i want to try with dual fan setup.

not i dun1 promo IceBlade, cos he no asking bout IceBlade maa...
he only gv 2 option, TT BT VX / CCF

lol... push-pull shold get beter result..

aiyak bro... PSU not support ma... will be resetting back if set FSB over 380Mhz..

set ram multiplier to X2 mean bus width for ram gettin higher n ratio gettin higer than FSB too.. rite or not bro?

how bout the temp bro.. hav try it b4?

correct if me wrong... TQ

This post has been edited by pie_86: Jan 7 2009, 01:48 PM

PSU not support? not RAM?

for temp,

google Core temp or HWMonitor.

use 4 stick HP ram bro... not support?huhh..

PSU use CM extreme power 600W

p/s: not find where button to setting multiplier ram bro at BIOS..huuu

This post has been edited by pie_86: Jan 7 2009, 02:38 PM

most of the time...when i didnt do 1:1..sometimes the RAM mhz quite high....coz its following the FSB...lets say if 1:1, FSB is 380, ram also 380...so multiplier X2 makes your ram 760mhz...so that means you got more head room to increase your FSB higher without reaching the RAM mhz limit ^^

ive tried OC Q6600 be4...not sure whats the TjMax..so i set to mobo to beep when core temp is more than 60C in bios.....when running orthos is stable at 3.5...temps showing around 68C...and the mobo is obviously beeping like mad

owh..like that ka?.. when i use Prime95... temp reach around 66-68`C... is that ok bro?

honestly..i will try to avoid going beyond 65...if possible...below 60...and 40-50++ at normal utilization

i dont want my processor life to get reduced lol...i think you know about it....heh...thats why i didnt push this baby (e4300) more...though it reach ed 3.6 before (70C beb)

owh.. 3.6 @70`C? wah..so cold ma...heee..

my normal usage temp around 40++ but when stress out it will reach around 60++..huuuuu

e4300 to 3.6 ler....70C is consider damn hot already...15 more C then system crash...lol 60++ ok la..best try not to exceed 65...then you wont harm the processor's life already