Anyone knows what is the safe minimal distance of the fan blade to the plaster board ceiling? Is 5" sufficient? Or must be more than 5"? Scared later if the fan wobbles a bit then the blade kena the plaster ceiling... coz planning to do flat plaster board, but leave a round/square hole in the middle just enough to fit the fan base through, so the fan blade will be quite close to the plaster ceiling.

My ceiling fan just stop responsing to remote control. Motor does not turn. any similar problem? Called SC and they say may be due to motor problem.

I nearly bought a few of it .. phew! Anyway saw ur post in ther earlier page, dated a few yrs back. I'm going for the Panasonic Yuragi fans.

Wise decision... Better go for the brand KDK or Panasonic to reduce all the unnecessary problem...

Really?!?!? Oh no..I have 5 units myself...so far...been running 2 months...fingers crossed!!

Then good luck to you and pray hard for you as well...
Hope your Deka fans serve you well....

how long is your hand?
i am 178cm tall and when i raise my hand slightly more than 7feet only

Hi all,

Recently, my ceiling fan is running slower and slower. As claimed by the technician, the IC board is malfunction. Thus, am planning to purchase another new fan.

I have some questions in my mind which need your advise:
i.) Is there any reliability issue of ceiling fan with remote control vs regular ceiling fan with same brand. or its based on luck?
ii.) Any significant differences between 3/4/5 blades ceiling fan (assuming same brand)?

Thanks in advance

Could be the remote sensor IC board spoilt, try change one from another similar fan and see it works.

---

Added on September 14, 2012, 12:08 amMine is all Euro Uno i bought 3 years ago. I read some say it is no good and i agree the sensor board is not very good.

Out of 10 sets i have, 3 or 4 sets the sensors already not well.One part spoil means 1 speed rosak. All spoilt fan cant turn at all. Put in a good sensor from another set it runs well again.

I have a few sets with speed 2 not working but can run speed 1 and speed 3, very irritating when usually i want speed 2.

Problem is this Euro Uno spare parts so difficult to get, if you can get it, your fan is back working again.

The motor no problem, only the speed sensors!

---

Added on September 14, 2012, 12:10 amanybody knows where to buy the sensor? The round IC board. I had 1 set repaired at RM40.

The fan i bought at RM185 in 2009 - 5 blades. I think it's worth just change sensor. Change new fan susah, have to call people, change sensor very easy, can do it yourself.

This post has been edited by guy3288: Sep 14 2012, 12:14 AM

I bought Alpha fan got 5 blades and remote control. Only cost 200+. And another type not sure wat the dfference but is only 100+.

Is it goot?

You already bought, too late to ask good or not. Just use and enjoy your new fan. Make sure find a good installer.

Ya just buy but wanna see if im a smart consumer or not lol.. see other ppl exp.

I just ask the elctrician install for me everything. Fan just ned to hook and join the cable not so complicated. All electricians shud be able to

How can u be smart when u buy only then ask... smart is ask 1st then buy....

I have the same doubt as well. Other forumers please enlighten.

Any sifu can recommend any shops in Penang which sells KDK fans?

Hi all, can any1 recommend which store in JB sell ceiling fans at a cheap price? Can any1 recommend me any model that is good with lights? needs the light to be very bright.... any1 have any comments on alpha wings? is alpha better or elmark? thanks a lot for ur help!!! =)

Hi All,

I'm the the market for the following ceiling fans :

Panasonic Bayu 4 (FM14C8)
Panasonic Bayu 5 (FM14D9-WT or FM14D9-CG)
KDK Baby fan (K11Z1-UD)

Anyone can recommend a place in the Klang Valley where I can get a good deal on these?

Actually, what is the difference between a 4 blade and a 5 blade fan?

Thanks in advance.

Please check with the hardware/electrical shop opposite The Shell Petrol Station at Jalan Jelutong. I was looking for the KDK fan K14XB-GY model, after checking with the KDK dealer, the best price i can get is RM250 but this shop can offer RM235.

Thanks for sharing. What the name of the shop?

Is this the model of fan that you purchased?

http://www.kdk.com.my/products-detail.asp?id=10

This post has been edited by CP88: Sep 20 2012, 01:59 PM

If you at Juru, u can get it from light studio.
Kdk K14X8 rm234 and regulator 3 blade white rm114