how ur mitsubishi fan?
i just install at my living and found out that speed 1 not much wind can feel ,except goes to speed 2.
but with the design ,n above speed 3-5. that good for me.

installed on my new place havent really get to try due to mco , plan to move in before april but shit happens so delay delay here expenses there expenses , now kitchen extension will be ready in 2 weeks hopefully i can start cleaning afterthat and move in asap, haha , so far when i go see the progress i alwasy turn on speed 3 ok la, never try speed 1 or 2 lol maybe when the temp is low with aircon on then can use it to circulate your place

I think so, as their packaging say that natural air ..
speed 1 very slow .. hehe

but then im ok with this la , 4++ with 5 blades.

Anyone here used NSB Veera or Xtreme? mind to share your experience here?

anyone know how to install KDK Baby Fan K11Z1?

https://www.kdk.com.my/wp-content/uploads/2...11Z1-Part-1.pdf

https://www.kdk.com.my/wp-content/uploads/2...11Z1-Part-2.pdf

Hi guys. Comparing

Living room
Econavi - 5 blades (RM719) Vs Sensa 5 (unknown price)

Bayu 4 FM14CZ - needed for dining (Quoted RM315) any alternative?

Study room and guest room regulator
FM12A0 Panasonic 48" regulator or KDK K12V0 48" (around RM150)

Please give some comments on the above.. are they same? Welcome to give alternative.


Tangan gatal looking at Moshon KDK. 1.5K alamak. Isit worth to spend X2?

This post has been edited by hahakat88: Jul 19 2020, 03:10 PM

Bought a cheap Faber 60 inch regulator fan to replace the squealing KDK RC ceiling fan. See how it goes.

Guys, based on the comments here, it seems like pana and kdk are the reliable brands. So is bayu OK? Cos not many ppl talking bout this model here.

And how should I choose the number of blades and the length? Currently incline to 4 blades, and its in the middle. Thanks.

yeap, Pana and KDK quality has dropped
hv u tested Alph fan, not bad i heard

Anyone can give their comments on Fanco fans? Are they worth it to buy?

Alph didn’t heard before. Is it reliable? Looking for reliable fan, not really into those fancy functions.

"A" was missing in his reply. Alpha, not Alph

sorry Typo
Alpha

I purchased few Panasonic fans recently and got it installed by the electrician.

Can I know is it common for the fan to wobble abit when operating and more when it's at the max speed? Or to what extent then we can consider the fan is wobbling? Is it as long as the case move abit even when operating is considered as wobbling?

I contacted the Customer Service and they mentioned that they will charge me if the fan wobble due to wrong installation so I was planning maybe to try tighten up the screws here and there first before proceeding to ask the technician to come over.

I'm a little OCD so even slight movement is bugging me quite a while.

Basically fan wouldn't wobbling when operating if installation and balancing is good skilled by the technician

long time ago, yes is good quality fan in Malaysia
Now i dun think so, most of my relatives install it recently complaining low quality.

Did the electrician do any sort of balancing of the blade during installation? Nowadays lot of electrician just install without any balancing done as presumably they believe the fan should be perfectly balance out of the box. But unfortunately there is other factor that influence this. As such there is such a case your fan can wobble if there is unbalance situation.

The technician would come and if due to balancing issue, its not consider wrong installation.

As such, you got 2 choice, ask your electrician to come balance the fan if he did not or ask the technician to do it for you but you get charged accordingly.

During the installation new Fan, Technician should do all the necessary technical checking n testing in term of balancing if not the technician taking for granted

Its normal if its the bayoo 4 series. The way the blades are mounted to the center hub is poorly designed. Its like you just hold the end of a long ruler using your thumb and a finger and try to keep it stable. If you use whole hand (4 fingers and one thumb) to hold that long ruler it will be much more stable. The former situation is the mounting of bayoo 4 using something like a clothes peg wire to hold the fan blade. The better one (latter situation) using hard mounting (failsafe and won't fly off) is the midrange (and higher) KDK series such as Vtouch Junior, Sensa 4.

You can try to pop off the fan blade "dinner plate" cover and tighten the 2 mounting screws (whilst pressing hard into the screw so it won't jump out/cam out and botak the + sign of the screws) for each blade to see if it helps .

To be honest, I installed 3 other KDKs and no issue. I have remounted that particular model bayoo 4 a total of three times from living hall, middle bedroom, and small bedroom and it still give windless feel + krek krek sounds of the blade scraping on the center hub.

The technician only ensure to mount the center hub and fix all 4 blades. It is not the job of the technician to balance fan blades. That is factory responsibility to deliver a working product. This is not like car tyre mounting.

The fan blades are balanced at factory level not at installation/end user side.
All have same weights as per the factory balancing stickers (they give a set of 4x 78.0 or 4x 79.5 for example), the factory wont give 3x78 and 1x 79.5.

This post has been edited by ceo684: Jul 22 2020, 01:46 PM