I just flashed 1.23ND version tomato from polarcloud ... works super great ... strong wifi signal .... the radio wave penertrated all the way third floor to ground floor .. i still get 4 bars of signal strength ... amazing ....its like my router was given a good dose of vigra ... very strong ... i recommend it .... but as for skin .... the interface presented looks ugly and discolored .. but i don't mind at all ... its goood ...

try Victek version. Interface looks great.


found out problem:

When login using IE7, QOS view detail load long time .. feel hang. but firefox don't have problem.

in qos setting there outbound is our upload speed right? and inbound is download speed right?

ya


no one can help guide me here?

why is it that when uploading at full speed or utilizing the bandwidth to the max speed the connection crashes (router is still running, still can browse website all)

but the pc i am uploading to cant be accessed, i tried it on few pc its the same thing happening

i tried with original 1.22 and 1.22 speedmod, the speedmod lasted half an hour longer before same thing happen
not enough ram?

haiz i also having prob of qos limiting xunlei

xunlei easy la not that hard for all p2p just block the bittorent protocol there inside qos and set the class to low
u can also add custom ports google for xunlei autentication ports and block generally all port above 4k to 65535

thats what i did

erm i juz wan limit somebody and not mine since i am paying and sometimes he took all my bandwidth. how i can do that? it seems doesnt work. can u show me how ur qos setting for this?

hmm also can be done set by ip range and assign static ip

u can also try to use mac address if u want to

tried but weird seems cant work.

wenhui100,

Always you have to execute "erase nvram" in Administration/configuration/restore defaults option ... then you will run w/o weird problems

I have been reading many comments about strange behavior in QoS, Basic Wan PPPoE defaults, .... please, do a erase nvram reset after you update your firmware, it will avoid almost of the complaints I'm reading in these posts.

Thanks

This post has been edited by Victek: Jan 2 2009, 10:49 PM

hi guys,

i'm new user to tomato, using tomato stock + vpn(i need openvpn), previously using dd-wrt. so far it is good except

1) i wonder if there's a feature to monitor bandwidth usage individually for each connected device (like dd-wrt), as i cant seem to find it? this feature so that i can find out who hogging the bandwidth at any time.

2) with QoS configured, running xunlei still causes other pcs cannot surf the net...anyone manage to QoS xunlei effectively? will using victek mod solve this?

my QoS setting as follows: (192.168.1.22 is my dedicated box for xunlei)

TCP/UDP
Dst Port: 53 Highest dns

From 192.168.1.22
TCP/UDP Lowest eeebox

TCP
Dst Port: 80,443 High www

TCP/UDP
L7: quake-halflife Highest cstrike

TCP/UDP
Dst Port: 21,20 Low ftp

TCP/UDP
Dst Port: 4000-65535 Lowest p2p

This post has been edited by unnamed: Jan 2 2009, 11:14 PM

victek version can solve this. lowest class for xunlei and limit outbound bandwidth (5% - 50%).
*suggest turn off DHT,Upnp.

but found out problem , PPPOE not stable and reconnect every 2-3hrs.
my last billion 7402gl modem connection active more than 90days.



question:
- If run 24/7 , does it use out all Free Memory ?? because memory keep decrease.

some tmnut iprange hardly get, don't want restart router.



wish tomato have this feature .... ~


today try Victek v1.23.8505 firmware. my wireless ipcam signal increase 9% -> 22% without increase tx power

This post has been edited by yangxi: Jan 2 2009, 11:35 PM

ok..i set Class A (default 1%-50%) for xunlei...now got no problem surfing...but xunlei dl like cannot reach max speed (half-speed nia)...need victek / tmnut / or what?

does ti support aztech dsl600EW?

Hi victek ....

I always did a (thorough) "erase nvram" i did everything ... even plugging and unpluging the router .... pressing the reset button behind the router ... .... b4 i do all the settings ... ...

After flash new ND version firmware and clear nvram. connection getting better.

but this router can't handle faster speed torrent?

get disconnect peak 400kb/s.




Jan 3 02:00:01 unknown syslog.info root: -- MARK --
Jan 3 03:00:01 unknown syslog.info root: -- MARK --
Jan 3 04:00:01 unknown syslog.info root: -- MARK --
Jan 3 04:17:18 unknown daemon.warn pppoe[116]: LCP appears to be disconnected (pending: 5).
Jan 3 04:17:18 unknown daemon.notice pppoe[116]: Disconnected.
Jan 3 04:17:18 unknown daemon.notice pppoe[116]: Connect time 624.6 minutes.
Jan 3 04:17:18 unknown daemon.notice pppoe[116]: Sent 1806241577 bytes, received 3496749250 bytes.
Jan 3 04:17:29 unknown daemon.notice pppoe[116]: Connected.
Jan 3 04:17:29 unknown daemon.notice pppoe[116]: IP Address: 60.53.x.x
Jan 3 04:17:29 unknown daemon.notice pppoe[116]: DNS Address: 202.188.0.133, 202.188.1.5
Jan 3 04:17:29 unknown daemon.info dnsmasq[396]: exiting on receipt of SIGTERM
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: started, version 2.46 cachesize 150
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: DHCP, IP range 192.168.1.100 -- 192.168.1.149, lease time 1d
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: reading /etc/resolv.dnsmasq
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: using nameserver 202.188.1.5#53
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: using nameserver 202.188.0.133#53
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: read /etc/hosts - 0 addresses
Jan 3 04:17:30 unknown daemon.info dnsmasq[1798]: read /etc/hosts.dnsmasq - 3 addresses
Jan 3 05:00:01 unknown syslog.info root: -- MARK --


Jan 5 03:59:16 unknown daemon.warn pppoe[826]: LCP appears to be disconnected (pending: 5).
Jan 5 03:59:16 unknown daemon.notice pppoe[826]: Disconnected.
Jan 5 03:59:16 unknown daemon.notice pppoe[826]: Connect time 625.1 minutes.
Jan 5 03:59:16 unknown daemon.notice pppoe[826]: Sent 1705174483 bytes, received 2354120756 bytes.
Jan 5 03:59:24 unknown user.info redial[825]: WAN down. Reconnecting...
Jan 5 03:59:24 unknown daemon.info dnsmasq[835]: exiting on receipt of SIGTERM
Jan 5 03:59:24 unknown daemon.info dnsmasq[1968]: started, version 2.46 cachesize 150
Jan 5 03:59:24 unknown daemon.info dnsmasq[1968]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
Jan 5 03:59:24 unknown daemon.info dnsmasq[1968]: DHCP, IP range 192.168.1.100 -- 192.168.1.149, lease time 1d
Jan 5 03:59:24 unknown daemon.warn dnsmasq[1968]: no servers found in /etc/resolv.dnsmasq, will retry
Jan 5 03:59:24 unknown daemon.info dnsmasq[1968]: read /etc/hosts - 0 addresses
Jan 5 03:59:24 unknown daemon.info dnsmasq[1968]: read /etc/hosts.dnsmasq - 3 addresses

This post has been edited by yangxi: Jan 5 2009, 08:13 AM

I don't know what's wrong with my router.

Qos and everything that shapes traffic is turned off, but I get graphs like this trying to surf the internet. When downloading, the graph is alright, but surfing gives such graphs.

I am on streamyx 1MB package

Click on WL tab or Br0 tab to know "who" is generating this traffic ...

I have recently upgraded from Tomato 1.21 to Victeks 1.23. Everything seems to be working fine but my CIFS client cannot mount the shared drive. All settings are the same but it wont connect. Any Ideas? Here is what the log is displaying:

Jan 9 16:09:01 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:09:01 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:10:03 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:10:03 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:11:05 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:11:05 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:12:07 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:12:07 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:13:09 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:13:09 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:14:11 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:14:11 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:15:13 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:15:13 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:16:15 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:16:15 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:17:17 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:17:17 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -148
Jan 9 16:18:07 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:18:07 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -512
Jan 9 16:18:07 unknown user.info mount-cifs[2237]: notice: Mounting...
Jan 9 16:18:35 unknown user.err kernel: CIFS VFS: Error connecting to IPv4 socket. Aborting operation
Jan 9 16:18:35 unknown user.err kernel: CIFS VFS: cifs_mount failed w/return code = -512

Thanks for the help if you can.

The CIFS share is a windows share and I use it for bandwidth stats.

This post has been edited by KsE: Jan 10 2009, 10:18 AM

i have been using hyperwrt + thibor firmware for more than 1 year on my wrt54g v2.2... its really stable... since been using the firmware for too long... my finger felt itchy to try another firmware... so 2 days ago i tried ddwrt v24 sp1... i even brick my router (power led keep blinking)... lucky can flash back...my 1st impression on ddwrt are the gui looks cool & have lotsa stuff but later i find it so heavy to load the webgui especially when i dc & connect few times on the row to find the best ip...

so today i try victek's Tomato_RAF_1.23.8505ND... so far so good... its a whole new gui for me... its simple & light...

thanks victek...