You can't since the router is NAT and PAT is not implemented. Only two IP's can be opened, first through DMZ to one IP and the second using a Portforwarding from port 1 to 65535 for a second IP, that's all..

Tomato RAF 1.23.8010 and 8500ND are out, new features:

_ TCP_Vegas values preconfigured already and GUI built in.
_ P2P extended buffer.
_ and the other mods of the RAF version.

Enjoy it!

Sorry, I forgot it, in the source code file you have one manual "How to build your customized Tomato firmware", open source, open information...

This post has been edited by Victek: Dec 17 2008, 01:55 AM

just wandering

is the bandwidth limiter below access restriction already remove on 1.23?

Amigo

Thanks a lot for the heads up I'll be trying this new version. It seems to be great on P2P stuff and TCP Vegas (+ with GUI)

Thanks again

Will be losing my router's uptime (again)

Edit : Not bad , 32+ people from Malaysia. Seems that lot of folks here are using this firmware ;P

This post has been edited by prasys: Dec 17 2008, 11:04 PM

which one to use for?
Tomato RAF 1.23.8010 and 8500ND ? sorry newbie here

depend on yr router support non-ND or ND.

ND stand for? and one more question. how to flash correctly . i meant the step. reset the router and flash tomato and reset again? what does this concern with nvram?

is this all to be done to restore back to original linksys firmware?

ND i think it stands for Network Driver , new Wireless Driver. It uses the new improved wireless driver

As for flashing step by step , you can check out tomato flash guide here :-

http://en.wikibooks.org/wiki/Tomato_Firmware

I noticed that the LAN and wireless MAC address are same, is it normal? I try to edit it, but after reboot, it still the same.

hi how u guys setup wireless? what mode u guys use?

i am also wondering about the same question

i got one question. how to view each pc dling speed? all connected pc using wireless interface is eth1. and at bandwidth there i cant know who is dling or not.

Well, test version of Tomato RAF 1.23.8xxx are growing fast since I have spare time in these days, please look at http://victek.is-a-geek.com to see last status, new functions have been added, IP/MAC limiter have been restored.

*- CPU overclocking
*- PFIFO GUI
*- Capacity up to 100 ports in UPnP
*- and many other

This post has been edited by Victek: Dec 24 2008, 05:50 PM

where is the option for vegas? i couldnt find it

btw, I still cant find the IP/MAC limiter too...

This post has been edited by gsan: Dec 24 2008, 05:59 PM

in the QoS>Basic, bottom page

This post has been edited by kitsuna: Dec 24 2008, 06:41 PM

what about the IP/MAC limiter?

not official yet, only available on test ver
can get at victek's tomato site, bottom page
removed on official release because of stability issues i think

This post has been edited by kitsuna: Dec 24 2008, 07:21 PM

Was removed due to continuous upgrade of ebtables in the official version causing problems to IP/MAC limiter modification, once I checked the official version went to an stable ebtables then I built the IP/MAC limiter.. simple as this.

Just bought WRT54GL v1.1 .

Flash this file?
-Tomato_1_23.7z (WRT54G_WRT54GL.bin)


can i revert flash back linksys official firmware??

Thanks

---

Added on December 27, 2008, 9:35 pmsuccess flash to tomato firmware ^.^


do i need Erase all NVRAM?

This post has been edited by yangxi: Dec 27 2008, 09:35 PM

anyone can help me verify, is it your router wireless and lan mac address are the same?