using cooler master hyper tx?
how the temp when load and idle?

Yup, cm hyper tx oni Idle at 58c and load at 66c

This post has been edited by za_az: Feb 24 2008, 11:46 PM

guys... got few nooob question here... what's a HT link? and is it imposible to get 1:1 ram fsb ratio ... cos i only used to OC intel...wan2 to try fiddle in amd OC as well... hehe

Actually in AMD we seldom call it 1:1 or whatsoever like overclock in Intel.
The correct term to use in AMD is ram divider.

But FYI, Intel's 1:1 is AMD's 400MHz divider.

-pWs-

thanks for the info there... cos when i look at cpu-z it only show me " cpu/11" for the ratio... btw...what about HT link? cos i read some guide says must reduce the HT link multi to x3... n i cant really get it there on y must reduce as i dont know the HT link affects what... hope u can enlighten me on that

EDIT: shud be HTT not HT link.... sorry for the mistake

This post has been edited by tkh_1001: Feb 25 2008, 12:34 AM

Ermmm
What mobo you use??

For starter, it is recommended to have HT Link below 1000Mhz.
HT Link = HTT x HT Multiplier.

HT Link is similar to Intel's FSB Strap IIANM.

-pWs-

oh..ok ok.... gosh... is there any place to understand amd OC jargons? looked at newbie thread for amd but din see any on the 1st page.. btw... i am using asus m2n-e OCing 4200 X2.... so that means HTT = proc fsb , HT link = resultant from proc fsb x proc multi right?

To clear your doubt.

HTT = Intel's FSB

HT Link = HTT x HT Multiplier
Clock Speed = HTT x CPU Multiplier

Ram Divider: 400, 533, 667 and 800 MHz

You can refer to the table which provided in the 1st page according to your processor multiplier.

For your mobo, it has very limited Vdimm. Dun expect high ram speed in this mobo.

-pWs-

ok... thanks alot bro... really appreciated ur help will give it a hit when i am free cos the rig doesnt belongs to me... but i am permitted to OC ....

wow.. what spec your friend having? mind to share?

Bro where u read those information?coz currently wif my setup HTT is running at 1114Mhz mean it is too high or?when i was playing Hellgate London there are a lot of artifacts..could it be the HTT porblem?

how muc ur vdimm bro?

most of d b.e walled @ 3.2GHz, so in ya case it's pretty normal.

timin of ram?

how's ya new b.e doin bro? mind to share? intel is just to fast to get bored with, rite?

3GHz I can reach, but yet, cannot pass orthos. If I want to OC above 3GHz with this brisby, need to add more vcore A burden for my proc that using only stock cooler

Overkilled~~ On air you could get ThermalRight IFX-14 is enough for you to cool down your processor enough

Here's come my new OC result...



And below are the error message when I try to OC it beyond 290Mhz even thou the HT Link alraedy set at 16bit



Any solution??

command rate change to 2T

Changed, yet still shows something like that, but if I insist to continue to windows even the message appear, it act normally, only everything will go back to default... means that the FSB = 200, etc etc...

wat bios d board is loaded with currently? try to flash to 0605, latest one are quite buggy to me. everything back to default becoz d system is unstable.

put htt to 200 and crank up d cpu multi. if not playin w multi buy b.e for wat...

This post has been edited by ah_khoo: Feb 25 2008, 09:06 AM

Drop your HT multiplier to 4X
Drop your ram divider.
change trfc to 195ns
it's either ram, HT Link or sub timings stop you
why don't you just remain everything, then push up the cpu multiplier only
since you're using 5000 BE, it has unlocked multiplier.
you can use this method to figure out what's the limit of your proc 1st without worrying your ram and your HT link

p/s: it's not FSB, it's HTT. No such thing as FSB in am2 platform
bro pws already explained it in earlier post

I had the error before also.
Continued and it reset everything.
Then went into Cmos again, changed again and showed same message, then i continued again and this time it booted my custom settings.
Anyway, mine was on the Cpu Speed.