no la..just for benchmark..and want to know how far this proc can go..will only use 3.1@3.3 for 24/7...

@tachlio
once u at campus pm me...want u oc my rig and teach me how to play with ram timing...

I only manage to get this.
But the ram is not tighten yet.So many error here and there.

y everybody super pi so fast one

oh ya...dblooi bro..cant use ur rma tweak la...whole comp hang =(
and 690g ram voltage high or no?


Attached thumbnail(s)

ur faster la bro..change the divider to 533 lor..put vdimm to 2.3(cas4)sure can boost up 3600/7=514..ur super pi should improve wayy better

He's right......
Tweak your ram,your gonna be way faster than 25secs.
I dont think i cant get 3.6Ghz.

bro OCZ, what vcore r u using?ur temp?

Im using 1.52V
My idle temp is 43C
Load is around 53C.

Everyone seems bragging about their Windsy F3

Here's my latest results -




AMD Athlon X2 4000+ Brisbane | mizivincible | Biostar TA690G | KVR DDR2 667 x2 | Cooler Master GeminII

Will prime longer Orthos later. Anyway, wanna ask sifus here, can this setup be my 24/7 system ? Just abit worry on the vcore side 1.5v. If yes it can be run 24/7 safely then I have no worries running this system.

This post has been edited by mizivincible: Dec 14 2007, 02:48 AM

Im not sure about it.
But some says windsor runs hotter than brisby.

But im using 1.52V for 24/7.So,i guess thats should be no problem for you.
Correct me if im wrong.

your pwm not hot ar using that vcore... 1.5xx u on water?
mine will auto shut down =(
bad cooling i guess ..

your OS not clean enough.
From the screenshot can see you are still using msn messenger

teach u a method, can instantly make ur OS clean and fresh for benching

start > run > type ' msconfig' > general > tick 'dianogstic setup' > ok > restart pc

after restart , open task manager , try to notice the ram usage

edited: TA690G max vdimm is 2.6v

you cannot use use that settings? Issit u try to change cas latency in the memset?
there are some sub timings cannot be changed tru the memset 1, else ur pc hang
those that i tell u , shoudn't be a problem, unless your MAL is way too tight adi
you can try MAL 7 or 8 ... should be usable most of the time

This post has been edited by dblooi: Dec 14 2007, 06:47 AM

No the errata will not cause problems. Actually its been fixed, but using a long workaround that sacrifices performance. With the next upcoming version of AMD Overdrive (or is it out already) it will allow you to turn off this workaround for full performance, but will result in occasional random hangs when at full load. The real reason why AMD did not want to release the 2.4Ghz proc is because its supposed to be a relatively high end proc, but because of the performance penalty of the workaround, it will not give the expected performance, plus if you turn off the workaround,

It affects all Agena/Barcelona processors revision B2 and earlier regardless of speed. It will be fixed in revision B3. Thing should get interesting after that, since the main impact of the workaround is that it slows down cache. Cache speed, and to a smaller extent size, is the main reason why the Stars arcitecture is losing out to C2D.

Any mobo can be voltmodded, its just a matter of understanding and manipulating the voltage regulation circuit. Google up the datasheet of the voltage regulator IC for a start. Btw, make sure you know what you're doing, most voltmods will void warranty, and a small mistake can fry a lot of stuff. Always check with a digital multimeter and take things one tiny step at a time.

Dunno why you're PWM so hot..even at 1.5v and full load mine is only roughly the processor's temp, which is around 60-65C.

this is my result at 3.6G
for you as reference

Thanks bro, and anybody else can still clear up my doubt ?

X2 4000+ @3.0ghz at 1.5v*

Idle 33-42 , full load at 50-58 (depends on wheather too =) )

Safe for 24/7 rig ?

*Refer to post 1989

This post has been edited by mizivincible: Dec 14 2007, 06:43 AM

what's your cooler?
the vcore is too high for 24/7 usage, as well as the temp

offtopic


bro -pws- , is time to go V4

I think you have check first.
My Brisby 36 @ 3GHz only need 1.45v.

Wait until 125 pages 1st

-pWs-

This post has been edited by -pWs-: Dec 14 2007, 06:50 AM

Using CM GeminII. Too high for 24/7 system ? Ala, have to lower down la then ? Anyway envy u guys that with lower vcore can achieve higher value.

And bro -pWs- please update mine ya ! Post 1989 =D

Going to enter V4 weehoo !

This post has been edited by mizivincible: Dec 14 2007, 06:55 AM

Nope,im using lapped xigmatek.ATM,not going for WC because its way too expensive for me.

Wah bro,u really make me......
Teach us 1 by 1 and step by step la bro.

Thanks for the info... maybe my board bios not doing well with this cpu...
will email abit about this

by the way...
i update a lot in ocmania.com ...
hope u guys join in and post ya result at there too =)
any good suggestion will be appreciated
thanks