my mobo got voltdrop problem...not sure abt the vdimm...i see at the pc health in bios...is around 2.3 but i set at the oc menu is 2.4 or 2.5..not sure..forgotten

no...2.2Vdim..cannot used stock vdim..cannot boot at all...

of cause... even u dun up the ram timing... and keep the mhz low...
the high speed cpu will torture da ram too =)
that's why overclocking need everything... pure power .. good ram... good board....]

but me use value @@"

This post has been edited by cyberloner: Dec 11 2007, 09:29 PM

my micron chipsets ddr2 need 2.1V to do 1ghz.
>1GHz Vdimm >2.2V

can suggest me micro atx mobo with good oc ability...biostar 690 ok or not?...

Not ok. The board is very very good in overclockability.

-pWs-

ok thanx..wanna change my asus m2npv-mx...is it worth or not

Go for it. I think TA690G is better than the board you using now.
I might be wrong too.

-pWs-

The only bad thing bout TA690G is cannot drop voltage. Th rest are absolutely hot! Especially fo a m-ATX board.



This post has been edited by nadeng1987: Dec 12 2007, 02:44 AM

Received ST56F today hooray. Pushing and pushing, but still got the same speed at same vcore , 2.92ghz @ 1.44v. Will do another diagno later.....

---

Added on December 12, 2007, 2:59 amAnd yeah, TA690G rocks, best bang for bucks ! Im using it and the functions are almost perfect =D

This post has been edited by mizivincible: Dec 12 2007, 02:59 AM

u're using what proc? i'm gonna do iced watercooling soon

This post has been edited by dj.eRicZzz: Dec 12 2007, 04:58 AM

G1 4000 Miss Brisby. Was hoping to get beyond 3ghz. U guys with F3 say bye bye to me lorrr, cannot catch up with u guys u guys too far ahaha.

Seems thats F3 makes OCer really2 mad.

Bro,what cooler r u using now? is your F3 too hot to be handle by air cooling?

i am making a site for overclocker...
hope u guys join in next time.... =)
playground for all ocmania ....

This post has been edited by cyberloner: Dec 12 2007, 07:28 AM

cannot drop voltage?
i seriously doubt that
if it cannot do so, how come i'm using 0.8v 1GHz now?

sorry to say , but low end asus mobo is just piece of s**t
ugly PCB colour , use all chaplang components most of the time and unocable bios on most of their low end mobo

and about TA690G , so far there are few cons that i know

1) voltage drop for the vcore and vdimm (max vdimm can set is 2.65v, but after dropping left 2.6v only )
2) vdimm set to 2.3v , real vdimm go back to 1.9v
3) clockgen can only be supported when u do some changes in PLL setup (is it one of the cons? )

but to me, they are just some minor bugs. In overall this mobo still damn solid for overclocking

stock....with other fan...the stock fan 3krpm only...now i'm using 5krpm but same size and all...

not say too hot but always average 40 at idle and load 46-50

i totally agree with you, any Asus board which is below RM500 are pure garbage. Not to say they suck, but the only good boards they carry are mostly the high end board. Their value boards are one of the worst.

this board poison me already,,i want to get it also

Thats not a poison,its like OCer helping OCer.

Does lapping both chipset heasink have any effect in cooling?