He is avoiding your questions.....

Hi All,

Can i ask for advise please. I have a contractor quoting me below :-

1) Motor for Autogate - swing type - Mid duty. Cant remember brand - 3 years warranty
2) New Gate - Metal ( about 5" x 10")
3) Build 1 concrete pillar (just one side cos another side got pillar)
4) 6 remote controls
5) All wirings including wiring for Door Bell and Light on the pillar
6) Autogate comes with Alarm function (in case any suspicious ppl, u can sound the gate alarm)

Total Price : RM5k

Is that ok ? thx

This post has been edited by coconutzz: May 4 2011, 01:52 PM

Sound reasonable, since it incluced concreate pillar...hope the wiring are Armout cable...

http://www.facebook.com/home.php#!/pag...134001629948605

try this.

New Contact: Mr. Tan 010-221 9496; Mr. Soon (Wei) 010-225 9496; Mr.Lim (Xiao Di) 010-226 9496

Lawrence here~!

My house installed with the GFM-905 DC MOTO autogate, but currently the controller got some problem. SO i would like to buy the controller to replace the old controller, can you help me on this.

You may contact me at 016-4110722.

Thank you!

Just installed DC MOTO GFM-905 from Spectra Alarm and Autogate System. You may contact Mr. Lim at 019-6237781. Fast and efficient service.

which brand is good for sliding autogate,my gate is stainless steel and quite heavy...do we need more powerful system for heavier gates,pls help ,thx

Hi all,
Could any sifu assist me on my swing-type autogate which running weird - during closing 1 side of the door started its soft-close way too early while the other side closed quickly and fully. The slower side stopped before it is fully closed, alarm sounded a short moment then it started its soft-closing again until it is fully closed.

Contacted the technician and what he did was logical to me:
(1) He tested and set the timing of 1 side of the gate, both opening and closing, it worked well.
(2) Then he tested and set the timing of another side of the gate, both opening and closing, it work well too.
(3) Then the tested a few times opening and closing with either single gate or both gates. The autogate work just fine in front of my eyes - i was totally satisfied and no complaint.

The problem is after around 1/2 an hour when i tested the autogate again it has gone back to the same weird closing condition. I dunno I should laugh or cry.

The control panel is like attached picture, setting part got one 1-digit digital display and two push-buttons.

Wish to seek sifu advice so that I can try to set the timing on my own.

Thank you & regards.





Attached thumbnail(s)

my panel is the old type using DIP switches to control timing for both sides making it easy to DIY

you should have spied on the technician to see how its done

Dear all

my house is under reno, i intend to install arma cable first, my contractor charge me rm17 per feet.

it is included arma cable for 2 light points on both pillars + change ori normal door bell cable to arma cable.

he say use 12 cores cables inside and use part of 5 for gate's both motors, 2 pillar lights & 1 door bell cable, the rest 7 can for future usage.

total lenrth abt 43 feet and he quote me rm800 inlcuded hacking and conceling, is it ok?

This post has been edited by papaya2: May 17 2011, 08:57 PM

apa itu arma cable???

i think you mentioned armoured cable..

what the cost like?

Anyone try this CASA Asia S-320 H? Which using new type of Arm (square instead of like ARM), any good?

http://autogatemalaysia.blogspot.com/2009/...320-h-easy.html

This post has been edited by Jo_da48: May 18 2011, 01:15 AM

yup, armoured cable, sry for make confusing... my price is ok?

ic....can enlighten a bit what armoured cable advantages over the normal? is it just normal cable with more line???

anyone have any good web site to see What design of gate could select either MS or WI?

I am very happy with my autogat contractor.

I got conned by someone, who supplied me a 16 fet swing gate tht is painted to look like wrought iron even though I said want galvansed. Thank God, not even 1 mth, the thing start to rust so I sent it back.

Then I got this guy to quote me. Then I ask to see what he has done, and after seeing his work sample, I had confidenc to engage him. With hot dip galvanise and powder coating, with the autogte motor, all in csot me RM4,800 for the 16 ft folding gate + RM1900 for the motor.

TOTAL COST = RM6,758.

Now my gate is the nicest on my street!!

This post has been edited by lizziewong: May 31 2011, 04:49 PM

16 feet... wow.. Metal price is high, better guard your gate

16 feet, very easy to park 2 cars!!

Guys,

Would like to ask, if I have a budget RM 2K for auto gate system (the gate + the arm motor)

What can I get? I have already laid and installed the armour cable. Now sakit kepala choosing what kind of gate and motor to use with the limited budget =.='''

Max I can go I think is RM 3K... but I want to know what brand and choice is being preferred normally... It's going to be 14 feet gate....

Please help ......