You think 60 is bad.. I reached 76 on Orthos that was really scary but anyway 73+ is max TCase so by right temps should drop after that because it will be downclocking.

This post has been edited by wodenus: Nov 4 2007, 09:11 PM

i edy get my e2160..
btw,i manage to get 3.15G stable..highest i can get 3.4G..but can't finish 3dbenchmark due to pc restart..
to all sifu2 there,i edy increase my
vcore volt to 1.45v
vdimm to 1.90v
Mch/pcie to 1.65v

which one i need to increase for voltage?
scared mobo get blow!

Voltage for what ? Is that a 1:1 ratio ? If you use a 1:1 ratio and you have good fast RAM, you might be able to push the FSB up quite a bit.

This post has been edited by wodenus: Nov 5 2007, 03:21 AM

yup,1:1 ratio.is it need to adjust ram timing?

This post has been edited by PGV3910: Nov 5 2007, 07:12 AM

don't have to fiddle with RAM timing.

oo..i see.thanks kentang emas
3.4G not stable. is it voltage not enough?
or that processor itself?coz on 3.33G the benchmark on graphic test run ok,when on cpu test,pc auto restart
what should i do?

hah.. looking at your cpuz voltage, it suggest that u put at least 1.52vcore!! probably more than that are u sure u only put 1.45vcore in bios?? what is your ram and the timing?? ah.. dont mess with the timing,, either put it at 4-4-4-12 or 5-5-5-15.. kingston value ram with hynix FP-Y5 mostly can do DDR2-900 at 1.9-2.0v with no problem at all.. some of them can easily pass DDR2-1000 at only 2.0-2.1v..

what do you mean CPU test? CPU test during 3dmark06 or something?

PGV.. and one other thing.. have you passed the orthos blend at least 8-hr stable??

yup,cpu test during 3dmark05..not try on 3dmark06 yet

---

Added on November 5, 2007, 7:36 amorthos blend?like prime95 ka?haiya..im noobie ler bro baok.. jgn mare

---

Added on November 5, 2007, 7:38 am is it my ram so powerful???ok,i try taruk voltage banyak2 lagi.

This post has been edited by PGV3910: Nov 5 2007, 07:38 AM

erm.. jgn taruk voltage byk2... for some reason (my case ler) those hynix FP-Y5 do not like high voltages.. not like micron.. 2.1vdimm is max.. but most FP-Y5 can do DDR2-900 at no problem.. mine even can reach DDR2-1000 at +0.3v at 5-5-5-15.. and DDR2-900 4-4-4-12 at same vdimm...

betul ke hang taruk 1.45vcore kat bios,, psl kat cpuz nmpk cm tinggi semacam ajer..

yup.. orthos ngan prime 95 tuh lebey kurang same je..

This post has been edited by baok: Nov 5 2007, 07:49 AM

Haha, ok, so try setting it to Enabled and up the CPU Host Frequency(Mhz) to 220 as a tester
Timings are ram related
Set to 1:1 divider


Mind trying 8x multiplier instead of 9x?

betul..aku taruk 1.45..skrg aku taruk 1.52 kat bios,dlm cpuz 1.57..WTH!bahaya ka ni??

Abit AW9D-MAX doesnt vdroop, if anything at all, it ups the voltage

Wow... also he should have gotten the M0 stepping.. the Tcase is almost 10 degrees higher on that one

This post has been edited by wodenus: Nov 5 2007, 11:31 AM

Serious noob here.

May I know the minimum requirement hardware for E2140 to reach 3.0Ghz? I know a overclock needs a good PSU, ram and motherboard. I saw alot of people here using a so-called P35 motherboard, what is it? I am using a sucky Abit LG-95C, am I able to overclock the E2140 to 2.6GHz at least?

P.S: Sorry if I ask in the wrong thread.

ok.. i'm thinking of getting another board for this E2140. Gigabyte G31MX-S2. What do you guys think, need a matx board, along with 1gb 800mhz stick.

get gigabyte p31 ds3L its same like p35 ds3 with the exception of a older southbridge, its below rm 300 la

dont get a 1gb 800mhz its bullcrap


just get a 667mhz rated and ramp the divider higher or pump fsb

---

Added on November 5, 2007, 10:29 pmbenison

regarding waht you posted at #389, do you have eist or c1E enabled, if so then it was NOR underclocking its the power saving feature.

This post has been edited by bryanyeo87: Nov 5 2007, 10:29 PM

The P31 has serious issues. Look at http://www.giga-byte.com/Products/Motherbo...?ProductID=2615 and read all the words in red

ewwwwwww, for 1 time in my life i believe a review and i get screwed in my @ss

Source