Intel Pentium Dual Core E2140/E2160/E2180 Thread, Discussion & Compilation
|
|
 Oct 23 2007, 04:41 PM
Return to original view | Post
#1
|
 
All Stars
14,990 posts Joined: Jan 2003 
|
QUOTE(goldfries @ Oct 18 2007, 01:49 AM) tips? no tips la. i just put the processor in, set 1:1 FSB:RAM ratio and FSB change to 400 and that's it. Good grief, what're your specs ? i don't touch vcore i don't touch vdimm i don't touch ram timing  yup. just ratio and FSB only.  |
|
|
|
|
|
Oct 30 2007, 05:04 AM
Return to original view | Post
#2
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(Are_keem @ Oct 15 2007, 12:43 AM) today's try.. Orthos is the best for stress testing, I can only really max out both cores with that. Also if you really want to test it properly you should maybe run orthos for a few hours.look at the vcore, is it dangerous? |
|
|
Nov 4 2007, 08:48 PM
Return to original view | Post
#3
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(PGV3910 @ Oct 30 2007, 12:00 PM) mine idle 32 load 45.. You think 60 is bad.. I reached 76 on Orthos even o/c idle is same but load reach 60.  that was really scary but anyway 73+ is max TCase so by right temps should drop after that because it will be downclocking.This post has been edited by wodenus: Nov 4 2007, 09:11 PM |
|
|
Nov 5 2007, 03:19 AM
Return to original view | Post
#4
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(PGV3910 @ Nov 5 2007, 01:25 AM) i edy get my e2160.. Voltage for what ? Is that a 1:1 ratio ? If you use a 1:1 ratio and you have good fast RAM, you might be able to push the FSB up quite a bit.btw,i manage to get 3.15G stable..highest i can get 3.4G..but can't finish 3dbenchmark due to pc restart.. to all sifu2 there,i edy increase my vcore volt to 1.45v vdimm to 1.90v Mch/pcie to 1.65v  which one i need to increase for voltage? scared mobo get blow! This post has been edited by wodenus: Nov 5 2007, 03:21 AM |
|
|
Nov 5 2007, 11:31 AM
Return to original view | Post
#5
|
|
All Stars
14,990 posts Joined: Jan 2003
|
Wow... also he should have gotten the M0 stepping.. the Tcase is almost 10 degrees higher on that one
This post has been edited by wodenus: Nov 5 2007, 11:31 AM |
|
|
Nov 5 2007, 10:42 PM
Return to original view | Post
#6
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(bryanyeo87 @ Nov 5 2007, 10:27 PM) get gigabyte p31 ds3L its same like p35 ds3 with the exception of a older southbridge, its below rm 300 la The P31 has serious issues. Look at http://www.giga-byte.com/Products/Motherbo...?ProductID=2615 and read all the words in red dont get a 1gb 800mhz its bullcrap just get a 667mhz rated and ramp the divider higher or pump fsb Added on November 5, 2007, 10:29 pmbenison regarding waht you posted at #389, do you have eist or c1E enabled, if so then it was NOR underclocking its the power saving feature. |
|
|
|
|
|
Nov 5 2007, 10:57 PM
Return to original view | Post
#7
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(Are_keem @ Oct 15 2007, 12:43 AM) today's try.. Sure you can't do that on stock Vcore ? Vcore here is 1.378 and it runs at 390 fsb, temps never go past 63. I'm not using one of those expensive coolers either, just a Rm45 CM Silence I installed only because the stock cooler was flexing the board.look at the vcore, is it dangerous? This post has been edited by wodenus: Nov 5 2007, 11:01 PM |
|
|
Nov 6 2007, 04:19 PM
Return to original view | Post
#8
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(likito @ Nov 6 2007, 04:14 PM) see this 2140 achieve 4.3gnz Have to see his ambient temps... and that's a pot. 4.3 Ghz on a pot is lame. Is that frost on the pot ? if it melts you're in trouble. It may be 4.3 Ghz but it's not feasible for daily use. cllick ME so impressive , wanna try 2140 , the batch is Q732A202 , can find similiar batch in malaysia ? Added on November 6, 2007, 4:21 pm QUOTE(benison @ Nov 6 2007, 12:26 AM) I look into it the board.. thanks for the advice. wanted to sell it off and buy the 6550. I was wondering why am I overclocking.. hehehe. Why mini ATX ?All your talk about NOR and C1E makes me feel like a noob. Whats that? Its not in the board.. probably the 945 gigabyte not good enough or does not have any of those feature. I just read the review. it looks like a ATX board, was looking for a mini atx to clock Added on November 6, 2007, 4:27 pm QUOTE(alfa99 @ Jul 29 2007, 05:31 PM) Hi all, Am running at 3.12 Ghz (390 MHz FSB) -- that's DDR790 at 4-4-4-12. CPU-Z reports voltage at 1.344V. Can go up to 420 but it gets unstable unless I turn the VCore up, but then it overheats really fast. Kmarc has gone up to 480 on the P35-S3L (which will be eternally out of stock now I guess.) People have gone up to 500 MHz on the Biostar P35 (which will also be eternally out of stock now.)I am joining the family, just bought e2140 + Gigabyte p35-ds3 today. But no ideal to overclock the new system. Decided to buy e2140 after kuchingfight able to OC it to 3.0Ghz, pretty impressed. This post has been edited by wodenus: Nov 6 2007, 05:00 PM |
|
|
Nov 6 2007, 04:59 PM
Return to original view | Post
#9
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(benison @ Nov 6 2007, 04:54 PM) coz.. i have a dell casing i would like to use. heh. picky fellow i am. Why not run naked ? I don't even have a case now |
|
|
Nov 7 2007, 12:17 AM
Return to original view | Post
#10
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(benison @ Nov 7 2007, 12:15 AM) I think I was able to overclocked it.. finally. I change the processor to e6550 and run it still having problem, updated the bios and voila. Silly me.. should have done that eons ago. Now to try back the e2140.. Yipeee Yay... what's the max fsb on yours ? |
|
|
Nov 7 2007, 11:44 AM
Return to original view | Post
#11
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(benison @ Nov 7 2007, 01:30 AM) 350. not too good. not sure if i have to do any tweaking. like lower voltage and such.. thats for e6550, have not tried on e2140 yet. I was wondering why did bryanyeo87 say its not necessary to go for 800 Mhz. I was thinking of getting it, but is it a waste of money. coz the price difference is 18 ringgit. It really depends on your RAM and cooling. In general to get higher speeds you increase voltage to the chipset, the processor and RAM. But doing that really heats up the parts, so you need a good cooler to go with that. You already have a 1:1 ratio right ? if you can push the fsb up to 400 MHz, then you won't need 800 MHz RAM because if you can run the FSB at 800 Mhz at a 1:1 ratio, you already have 800 MHz RAM it's also true that you might be able to push 800 Mhz RAM above 800 MHz though.This post has been edited by wodenus: Nov 7 2007, 11:55 AM |
|
|
Nov 7 2007, 01:15 PM
Return to original view | Post
#12
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(ah_khoo @ Nov 7 2007, 01:00 PM) guys, just a quick check, any M0 user here? if there is, how far can it fetch? M0-stepping E2140 here, I've reached 420fsb but I have to raise the vCore to 1.475  still new to intel, many thing to be learnt...   I turned that one off after temps hit 76C it's on a cheap cooler now while I wait for extremeocer to make me a phase-change cooler. If he doesn't run away with the money (LOLOL just kidding !! ) I should be able to run at least 420 fsb when I get it. Now running at 390fsb, Orthos stable for 7 hours 45 minutes, OCCT 1 hour was stable. Got to try for longer.This post has been edited by wodenus: Nov 7 2007, 01:16 PM |
|
|
Nov 7 2007, 02:31 PM
Return to original view | Post
#13
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(ah_khoo @ Nov 7 2007, 01:30 PM) yup, mine is mo e2140 too... what's ya highest clock with stock voltage (1.325v)? i'm currently burnin d chip, not doin so well (2.8GHz) but just a fore play as i'm still nuts in intel oc... Currently at 3120 MHz (390x8) at 1.376v. Am using a CM silence on it (Rm45 ! ) but I have fans everywhere on the board. Idle is 37c. OCCT/Orthos load pushes it up to about 67c. The nice thing about M0 is that the max Tcase is 73c, so you can push it up a bit higher before the protection kicks in and lowers everything. I have two fans blowing on the RAM (just removed them from old processor HSFs), one fan on the processor MOSFETs, and one 8cm case fan above the NB. Also I have EIST, C1E and TM2 on so the divider drops when I'm not gaming. QUOTE(ah_khoo @ Nov 7 2007, 01:30 PM) ic, thanks bro. one thing i notice bout this 2140 is regardless voltage, be it stock or way up to 1.375, d load temp is alot diff then idle temp (usin coretemp 0.95.4). on load it can go as high as 60'C, while on idle d temp read is just only 30 (+-3)'C. is this normal? Load is 67c here... but then max Tcase on the M0 stepping is 73c, so I still have room. Can't do much higher w/o pushing voltage though. btw, i'm runnin d chip on old skool 965p ds3 (rev 3.3) board with a pair of d9dcl, d chip cooled by katana2 used on my old rig b4, kinda outdated...  |
|
|
|
|
|
Nov 7 2007, 07:28 PM
Return to original view | Post
#14
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(ah_khoo @ Nov 7 2007, 06:48 PM) yeah d feelin is nice when figures are involved, but still i wun swear myself to intel... Gigabyte does seem to undervolt quite a bit. gigabyte 965p ds3 undervolt alot ar? [attachmentid=325921] |
|
|
Nov 9 2007, 01:49 PM
Return to original view | Post
#15
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(ah_khoo @ Nov 8 2007, 12:58 PM) stock voltage is reported as 1.325v. d stock cooler is still untouched, infact, i never use any stock cooler for my own rig... Gigabyte hides the RAM timings for some reason. If you press Ctrl-F1 at the main BIOS menu you will see the options after you select the MIT any 965p ds3 user here? wat bios should i load in order to adjust ram timings manually? i'm on f12 currently & there's no such feature at all...  one more thing, when u guys mentioned certain clock at certain voltage, is d voltage referring to d load voltage shown by cpu-z, or d one set in bios? there's a big diff in my case... |
|
|
Nov 27 2007, 07:04 PM
Return to original view | Post
#16
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(Shoot@M3 @ Nov 27 2007, 06:54 PM) Newcomer here Hm... what HSF do you have on ? Long time no OC edi Pentium Dual Core e2160, 1.8GHz Now at 3.33GHz (stock voltage, stock cooling) Paired with GA-P35-DS3L Lousy pair of RAMs, KVR667 Lousy 7300GT PCI-E VGA  |
|
|
Nov 27 2007, 07:18 PM
Return to original view | Post
#17
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(kucingfight @ Nov 27 2007, 07:12 PM) as he mentioned stock cooling already? Oh right didn't see that  |
|
|
Nov 28 2007, 10:13 PM
Return to original view | Post
#18
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(Snyy @ Nov 28 2007, 07:39 PM) aiks. my previous post gone. oh ya, I did try these timing. but still no luck. cant pass 360 FSB. Updating BIOS in Windows is not really a good idea cos it's slow, and if something interrupts the transfer, you'll get write errors. Try updating via DOS, it's much faster and safer as well.I faced an issue when I try to update my BIOS using @BIOS in windows. Below are the screenshot. anyone can help? This post has been edited by wodenus: Nov 28 2007, 10:17 PM |
|
|
Dec 3 2007, 11:09 AM
Return to original view | Post
#19
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(huh? @ Dec 3 2007, 11:01 AM) i was pretty bored and too many assignment to do till ive freak out last night..!! hahaha.... VCore is fine... yes you gotta get a better HSF... and better TIM. And then maybe. You might get air-conditioning while you're at it lol lowered the multiplier to 8 and up the 1.2 NB volt to 1.4 in the bios, vcore at 1.36 and i hit 330 fsb.. didnt try any lower multiplier than that cause i was too hungry.. with the same volts, tried fsb 300 with multi 10 and it booted up! what a suprise.. run orthos but failed after 1 minute..i then set the vcore to 1.38 and run orthos again and now my temp is hitting 71 C.. what the fisH? i stop the test and revert back to 2.9 ghz setting.... going to get a better HSF soon and post the OC result.. the vcore is too high for a M0 stepping processor right? im pretty sure i got a poor batch of 2180...nevermind, maybe better luck next time This post has been edited by wodenus: Dec 3 2007, 11:11 AM |
|
|
Dec 4 2007, 03:08 AM
Return to original view | Post
#20
|
|
All Stars
14,990 posts Joined: Jan 2003
|
QUOTE(andx517 @ Dec 3 2007, 11:08 PM) omg finally i finish reading these 35 pages sorry im new here i need some suggestion, im low on budget, ima going to get following items 1. Intel E2160 M0 Get the 2140 instead.. cheaper. QUOTE(andx517 @ Dec 3 2007, 11:08 PM) 2. Gigabyte P35-DS3 works QUOTE(andx517 @ Dec 3 2007, 11:08 PM) 3. KVR667 1GBX2 (Hynix FP-Y5) works well QUOTE(andx517 @ Dec 3 2007, 11:08 PM) currently using Enermax Noisetaker 320 True Power, not enough rite? Not sure ... Enlight 350W here running 2140 at 3.2GHz, 8600GTS at 700/2100, 80GB HD and DVD-RW drive. This post has been edited by wodenus: Dec 4 2007, 03:12 AM |
|
Topic ClosedOptions
|
| Change to: |  0.0369sec
 0.60
 7 queries
 GZIP Disabled
Time is now: 8th December 2025 - 04:42 PM |
Quote