you think that is high?

you havent seen goldfries oc on stock vcore

hehe..
bro kentang emas, mind to share some tips?

aww my 2180 cant stand orthos more then 4 hour...

GTG

Use OCCT, it detects errors faster then orthos

tips? no tips la. i just put the processor in, set 1:1 FSB:RAM ratio and FSB change to 400 and that's it.

i don't touch vcore
i don't touch vdimm
i don't touch ram timing

yup. just ratio and FSB only.

not necessary...

i've encounter many times OCCT pass for 1hr or two hour (costum set) but failed orthos after 7-8hour

and my E2160 at 3.2gig is fail me after 11hr of orthos!! so i think i have to bump the vcore until 1.475 if anything more than 1.475 i just happy to use 3.0gig only..

Not clean off the goop intel uses on thier hsf first and replace with Mx-2 ar?
Eh try oc higher, and go enter world record, current is 3.6/3.5 or so on air cooling



Hmm, duno wor...mine is the other way round, occt fails before orthos :S

whats the vcore of it when its 3.2ghz and orthos failed?

and orthos you select blend or other options? i selected mine as blend...

This post has been edited by bryanyeo87: Oct 19 2007, 03:35 AM

"i dont want to play with vcore cuzz i want my proc to live longer..."

this is my stand....izzit relevant..??

GTG

u ady know wat u doing right..

depends sometimes the temps kill the proce even before the volts do

hi bro can help hre..?...for 2140 is supposed to be 200X 8..I set fsb to 250 but cannot see the increase..Use cpuid cannot see or the mb not respond mb--BiostarP4M900

This post has been edited by ronho: Oct 20 2007, 07:00 PM

3.2gig @ 1.4625v orthos costum (up to 4096kb FTT lengt and 5min time.. costume from blend actually ) - failed after 11hrs++
and over 20hrs stable at 1.475vcore..

so i just happy to run it at 3.0gig @ 1.45

---

Added on October 20, 2007, 8:40 pmdont afraid ler to bump your vcore

This post has been edited by baok: Oct 20 2007, 08:45 PM

didnt dangerous eh?
wanna bump it to 1.5v and see what happen.
haha..

how about chipset overvoltage?

Normally via chipsets are not for ocing :S, you may try with clockgen to pump fsb
and turn off C1E and EIST in bios

Use 1024 fft and 64 fft, let the cpu burn in first
err...you sure you got the settings correct anot? abit high for a L2 stepping...maybe possible to lower the volts if some settings are changed



just make sure you up the correct one (NB) and not the (SB) and have active or good cooling on the NB

erm.. i run orthos cpu stress for 24 hrs first at stock before try any oc attempt..

i run 4096fft priority8 on purpose.. the proc is 3.0gig orthos and occt stable at 1.4375v but when play games, sometimes it hang.. sometimes it restart.. sometime bluescreen.. that's why i decided to increase the vcore until 1.45v and now everything stable.. not yet finish fine-tuning but priority now is to finish my assignments first and until my last paper final exam, i wont touch anything..

erm.. my own rule of thumb.. (my own ler.. not others..) if u use hi-end aircooling, then dont afraid to bump until 1.45v... if u use hi-end wc, then just go for 1.5-1.55.. anything higher i wont run it at 24/7.. of course, however, at your own risk

This post has been edited by baok: Oct 21 2007, 01:18 PM

not an excellent overclock but still a good one i think

E2140 @ 3GHz temperature readings . Anyone can tell me ?

Hi guys, I going to get an Intel Pentium Dual Core E2140 + P35 DS3 soon. Just want to know is there any stepping of E2140 will give a better OC result? I also going to buy a 2*1GB Value RAM. which RAM (what chipset?) you guys will recommend?

for value ram.. try to look at Kingston with either Hynix FP-Y5 or ELPIDA chipset.. but if you found Crucial Value Ram, grab that instead!!

Good grief, what're your specs ?