plug in floppy molex also does not solve the problem........have to try flash bios already now........

Edited: after few hours trying, manage to Flash Bios to the lastest version and fix everything again......but it seems not working too....... OMG.....

This post has been edited by LExus65: Jun 2 2007, 01:55 AM

pack everything and send it for rma. btw, what the relevant with plugging in floppy molex? it activate something? my friend has this board too. too bad he use it for normal daily use. totally overkill

sad.. this will make it failed to impress OCer.. NEED PENCIL MODS FOR VCORE >>>>>> DROOP IS TERRIBLE >>>>> BIOS SET 1.6V >> Windows Idle 1.55V >> Windows Load 1.48V
does all asus mobo have this pr0b?

how bout this dark infinity? plss advise

at least it still can be cure with a pencil. asus=vdroop

AFAIK, infinity has it too

check this one out. vdrop max of 0.02v
http://vr-zone.com/index.php?i=4966&s=9

Infinity vdroop is good, very little, mine is around 0.012v. Asus board has great vdroop all this while on every mobo.

ahh ic..but i dont like very very much on pencil mod upon my mobo

well, does infinity dark display almost correct vcore when browse with cpu-z??

nope,not accurated at all when read at cpu-z,i put 1.55vcore it shows only 1.2 something....
my dark vrop at 0.02v,around like that

so far i used only one mobo has no vdrop,the kapak jahat generasi kedua.

CPU-Z will only read vcore <1.4v real. Any value higher than that will shows you 1.2v++. You can use ASUS Probe for Asus mobo or Smart Guardian for DFI. Also, Speedfan is another choice for every mobo.

speedfan is not accurated,only certain sensor or mobo will do
what about everest?

IMO, nothing is accurate.
You want something accurate?

Use "Laser Temperature Sensor".

Just set up the rig, initially everything was good. Memtest a few hours @ stock vcore E6420 @ 3.2ghz, ddr800 everything auto. After that, I changed the dram timings to 4-4-3-auto in bios and 2.2v bios, supertalent t800ux2gc4, memtest was good and i rebooted. Upon rebooting, the mobo gives a error one long beep and nothing else happens. So I went clearing bios and boot up fine with default settings. Then i hot reboot again the same thing happened again, one long beep, nothing else. SO i turned off a while then turn on from cold boot, everything ok, then hot reboot same thing happened. And now, cleared bios, cold boot, the mobo gives a long beep, nothing happens, even clearing the bios doesnt do. Any advice? bios corrupted?

btw: soft reset doesnt seems to work for me (stock bios), hold insert+reboot, have to manually reset, so will this damage the bios chip?

This post has been edited by anangryorc: Jun 2 2007, 07:49 PM

i think i have manage to solve my little crisis after doin few hours of burn in with sandra sisoft and dun let the Smart Guardian to run automatically at startup....... weird problem.........

My Infinity P965 with E6600ES B0 revision 501fsb X7



Attached thumbnail(s)

my mobo bios doesn't have Channel 1 CLK delay something.... weird

eh..24/4 bios solve the B0 ES proc problem edi?

just got my board today trying to oc now

haha, overkill man. A near 1K gadget to measure temp, not for us to play with. Industrial will definitely invest in it.

Certain mobo will suit the speedfan, some others will suit the Everest, have to try various types.

so hard to hit 3.4ghz with 1.325v,my ds3 can do it easily =( now using 1.5v

Update your bios to 0424, and try again.

in computer enthusiast, there is no place for Expensive word

im quite sure among us, or atleast must got ppl who owned this laser temp sensor